Having problems with your Vacuums ?

Take apart wet head of a vax 6151t to replace tubeing

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Take apart wet head of a vax 6151t to replace tubeing

... Vacuums

I need to find a way to replace the attachment hose on this unit. the tube to spray the detergent snakes into the base next to the wheel and i'm unsure of how to take it apart without breaking it. is there a simple way to remove the wheel? do i need to do something special to replace that tube?

The best thing for that situation is to look on the side of the road and you will find a Bissel, I see one or two a week. Take one home and experiment on that one not yours. I have brought many and never have I bought one. I never see a Hoover by ... Bissell 9200 Upright Vacuum

Oreck XL21 just will not work at all any more. Beater is clean - belt is fine. Fresh bag - inflates. Took the thing apart - checked for blockages at intake, bag entry, and the tube. It just doesn't vacuum anything. No suction at all for anything stronger than air. I'd say it doesn't ****, but that would be ironic. Are these known for just "quitting" after a while? We take it in for maintenance as recommended to replace filters, etc. Is there some miracle trick to make it work or sho

Did you make sure the brush turns freely? Even though it is clean, if it does not turn freely with the belt, it will not beat the carpet and pull debris up into the unit.\015\012\015\012Another (drastic?) thing to try would be to take the unit ... Vacuums

My powerhead on my EXL Tri-Star goes on then shuts off. When youturn it upside downit runs, then back on the floor it stops. Is it the belt inside the powerhead and if so to I take the head apart and replace this belt. Can any vacuum repair place fix this if I have the part. Vacuum was purchased in March 2000 Thank you, Dianne Miller [email protected]

A vac shop is probably going to require you to use their parts for warranty purposes. but its pretty simple. most shops should be capable to do it. ... Vacuums

Vax 6131 water pump had stopped working on taking apart it had over heated and plastic casing had melted in one place,obtained new pump from buy spares which matched old part fitted and reasembled but pump does not run ,is there any internal fuses ? Or any thing else to replace

... VAX Appliances Vacuums

How to take apart a vax

... Vacuums

How do you take apart a vax mach2?

... VAX Appliances 2000 Canister Vacuum

I have a Kenmore Progressive model 116.22812204 purchased 2003. The swivel (part nuumber 8195133) that attaches the extension wand to the power mate attachment snapped, so I can't keep the parts connected. I can order a replacement part on-line, but I don't know how to replace it - is it difficult to take apart the power-mate and replace this part? Do you have instructions on how to do it? Thanks!

... Kenmore Vacuums

My mother purchased a replacement hose assembly for a Bissell ProHeat 2X and the part was shipped without any instructions... While I am pretty handy, my issue is with the supply tube, and I cant figure out how to accomplish the replacement, and as its not MY vacuum, Im hesitant to start taking things apart.I just need instructions to replace the entire hose assembly.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Manual for taking apart vacuum head for model 1163493592C

... Kenmore Vacuums

How to take apart Dyson DC 24 cleaner head assembly

... Dyson DC24 Animal Bagless Upright Vacuum

How do i take apart a nutone central vac power head?

... Broan-NuTone CV353 Central Vacuum

How do you take the Dyson turbine head apart?

... Dyson Vacuums

The power head keeps shorting out during use. one of the connecting prongs from the handle to the power head is black instead of silver and is smaller in diameter like it has been arcing inside the connection. could this be the problem and if so can I replace it or will I have to take it to a repair facility. Thank you for your help, Jim Carey [email protected]

This is a problem with the connection in the wands and the powerhead. Because they are shorting out you may have to replace the neck on the power nozzle. (Leave that to a pro). But you will definatly have to purchase a new wand as replacement wires a ... Electrolux Lux 7000 Bagged Canister Vacuum

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I

You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

Can you take the Swivel Sweeper battery pack apart to replace the batteries with new rechargeable batteries? Batteries look like AA or AAA, but it appears that the battery pack is sealed. Is there any way to get it apart:?

Yes you can if you have a way to cut through the plastic outer case,(I used a Dremel rotary tool). Inside you will find six double A Ni-mh batteries. I found eight of these for sale on ebay for around ten bucks,then all you do is solder some wire to ... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum

I have a Kirby Heritage II which normally works amazingly well, but it's not playing at all nicely today - and of course we have apartment inspections tomorrow. *dies* The belt broke today (as did the replacement belt, which I'd bought at the same time, so apparently the rubber was old), so I went over to Stark's to get some new ones - but it still won't cooperate. I've taken the head apart and put it back together several times, to be sure that everything is properly seated, but it's just not

... Kirby Heritage II Vacuum

Have a Kirby Heritage II vacuum. Need to replace a split fill tube. How do I remove the outer cloth bag from the mini-emptor, and then how do I take off the old/attach a new fill tube?

This repair guide should answer all of your questions...http://reviews.ebay.com/HOW-TO-REPLACE-REPAIR-KIRBY-VACUUM-H ... Kirby Heritage II Vacuum

Wondering if the head is plugged up because it makes a sound like air is escaping somewhere. I've replaced the original cloth bag with a comparable "O" paper bag from Sears. I tried to see if there was a clog in the hose by placing a broom handle in the hose to see if something would loosen. I also cleaned the filter and the air filter. If the head is plugged, how can I fix it? We can't get the vacuum apart. Thanks.

I had this problem, but suction improved when the attachments were properly secured in their holders. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

How to take apart shop-vac tubes

Twist and pull? Beat it like it owes you money? Heat the outer part? ... Shop Vac Vacuums

How do I take apart my Bissell Cleanview Helix to replace the power cord?

... Bissell Cleanview Helix Vacuum

I need to take apart a vax cylinder hoover to service it

... VAX Appliances 2000 Canister Vacuum

How to take apart wand of kenmore vacuum 116.24614400 to replace COVER #8191782 on Sears part

... Kenmore Vacuums

I broke my kirby generation 3 vacuum cloth bag latch i found where to get the part but how do take it apart to replace it

... Kirby Generation 3 Bagged Upright Vacuum

How to take apart Nilfisk Action Plus to replace spring loaded cord retriever

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0803 seconds