Having problems with your Vacuums ?

I have a George vacuum and it's died. I have

Answers :

Of course, you should double check the plug-in recepticle - just to be sure you have not thrown a house breaker. The easiest way is to simply plug something else into the same recepticle. If you simply move the vac plug, you may choose another recepticle oparating on the same breaker.

How did you check the fuse? Fuses can fool you. As a general repair tech, I learned long ago not to rely on my eyes. I have a multimeter and do an ohm check - because sometimes a fuse can look ok, but actually be burned in-two where its not easy to see.

All that ruled out, the most common thing that stops functioning when a vac dies is the switch.
That ruled out, when vacs die it usually the switch.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a George vacuum and it's died. I have

Of course, you should double check the plug-in recepticle - just to be sure you have not thrown a house breaker. The easiest way is to simply plug something else into the same recepticle. If you simply move the vac plug, you may choose another rece ... Vacuums

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall

That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

I was vacuuming and my hoover vacuum died

They have a thermal shut off on the motor so if it gets too hot it shuts downcan take up o 30 min to reset check all filters make sure nothing is blocking ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Bosch Vacuum Cleaner: I changed bag. Cleaned out all suction hose and hepa filters, however, my 1450 w 12 amp upright vacuum cleaner will die after five minute run - overheating. Please advise.

Greetings from GoVacuum.com,It sounds like you may have a bad thermal switch inside the machine. Most vacuum cleaners have a switch connected to the motor, so if the vacuum cleaner is running hot, it will shut off to prevent any damage ... Bosch Vacuums

My vacuum died. It won't turn on. It is not the outlet. Is it a blown fuse? How do I replace the fuse? Where does it go? This vacuum is a little over 2 years old. My older Hoover WindTunnel STILL works and has never had this problem.

It's probably the power switch. My switch was dicey for a couple years, finally gave out. Easy to replace.\015\012\015\012Remove the two screws just above the WARNING on the rear of the upper handle assembly, then slide the whole assemb ... Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum

Hello, I didn't notice that the bag on my miele was full and kept vacuuming until the vacuum turned itself off (died). Have I done irreparable damage to the motor, or will it work again once it has cooled off? Thanks.

Permanent damage is extremely unlikely. It should work just fine when it has cooled off. ... Miele S318 Bagged Canister Vacuum

On an old upright prolux plus, I just replaced the belt and cleaned out the brush motor, ran the vacuum for a bit, then the vacuum motor died...it's always run great. any suggestions of what to check?

... Electrolux Vacuums

I have a kenmore canister vacuum model 116 nose 360, i was running it ( just the vacuum no beater bar ) and it just died.

... Kenmore Vacuums

My vacuum died

It might have blown a fuse. ?Check if this model has a fuse ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

My vacuum is loud and dies

Your impeller is broken that make motor work harder and shut off ... Eureka 4700A Maxima Bagless Upright Vacuum

Hoover power drive vacuum cleaner simply shut off and died

My hoover vacuum is very hard to push forward but easier coming back.Any help will do. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

Dirt Devil vacuums for about 3 min,than dies out.Help

... Dirt Devil Vacuums

My Panasonic vacuum cleaner MC-E461K has died.

... Panasonic Vacuums

Hoover Vacuum My Hoover cannister model s3614 "runabout powermax" suddenly lost power to the agitator roller in the rug brush. Where the wire cord enters the power brush, the covering has rubbed off exposing the wires which are not bare but still have their own covering. For a while the power came and went as I manipulated the wires but finally died. Is this something I can fix myself or is it going to be an expensive professional repair? (Warrantee has elapsed.) Thanks.

Our Hoover upright vacuum cleaner makes a very loud noise when it is running. What causes this? ... Hoover S3614 Vacuum

Need manual for george gve370-2 - Numatic GVE370 Canister Wet/Dry Vacuum

... Numatic GVE370 Canister Wet/Dry Vacuum

It sparked and died! the filters were clean and there were no clogs the machine is about 6 years old! I love this vacuum is there any fix?

Most likely the motor has failed, or possibly the switch.Replacement motors and switches are avaible on eBay for about £25 / £5, however replacing either requires good DIY skills and tools.Have a look at ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Need a manual for G100 George Foreman Grill - Vacuums

... Vacuums

Problem with an LG Vacuum Cleaner Model # V-CA504CEU. Has No Power,Just Died. Any Ideas Anyone???? Thanks, Derek

Did you ever find a solution? i am having the exact same problem with the same model. ... LG Vacuums

Kenmore special edition canister vacuum 360 help filter dies after a little while

... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have a dyson dc05 absolute turbobrush vacuum. turned it on and it slowly died in seconds. then tried to turn on again and only came on sporatically for a moment. Is it the on/off switch or motor?

Hi there VacuumGuru for vacuumspot.com.au here. It is likely to be the motor for that model but it is easy to test. I will answer this with the assumption that a person wouldn't try to repair something they are not qualified to do. All you have to do ... Dyson DC05 Bagless Canister Cyclonic Vacuum

My hoover power drive vacuum simply died. It just shut off. I checked the plug, etc...I just can't get any power...Can you help?

If no light or motor sound cord is probably bad. Look near AC plug or just replace the plug end. Check with ohmmeter for continuity with switch ON. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

Usermanual hi im trying to find a downloadable user manual for my numatic george GVE370 3 in 1 canister vacuum cleaner please can you help

Contact Numatic, they will send you a user manual for free ... Vacuums

Dies after a few minutes of vacuuming

The thermal cut-off in your machine is activating - this indicates that you have a blockage or a clog in the machine. The machine will turn itself off so that the motor doesn't overheat - the machine will cool off and you'll be able to turn it on aft ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My roomba 560 works perfectly for a year. Now works ok, vacuum but the dust stays at the bruches and at the bin. i replace the filter but nothing. Thanks George

You need to decide if the vacuum and brushes are runing or not. For me its easy to determine after its run. If the brushed turn then I have debris in the open part of the collection bin when I pull it off the back, but none if the brushes don't turn. ... iRobot Roomba 560 Robotic Vacuum

Vacuum shuts off after short run time . it will turn back on after about 5 minutes but then dies again

Hi,\015\012 This is overheating and tripping the thermal cut-out on the motor.\015\012 You need to strip off all filters, clean or replace them (if caked solid). Very often panel filters can be cleaned by knocking them on an outside wall, ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0816 seconds