Having problems with your Vacuums ?

Kirby vacuum cleaner G4 fitting new fan order of assy of washer and seal ...which way does the soft seal face and assy order of soft washer, I assume the steel washer is next to the retaining nut/pulley. Ozzie

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kirby vacuum cleaner G4 fitting new fan order of assy of washer and seal ...which way does the soft seal face and assy order of soft washer, I assume the steel washer is next to the retaining nut/pulley. Ozzie

... Vacuums

The rainbow e series is leaking water when running-I assume that I need a new seal? If so, what is a good website to order from

Clean your water separator. That is the thing that spins around in the water pan, that it attached to the motor. It is a bunch of slots around it. Like a strange fan of some sort. The nut holding it on is half ench. Use a tooth brush, if you do not h ... Rainbow Technologies D4 Bagless Vacuum

How do you replace the steel pre filter catch? Mine broke and I ordered another, but how do you get the broken one out of unit in order to replace it with a new one?

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hoover model U6476910 I was cleaning out the bearing sections of the brush when a spring type pressure washer fell on the floor. I did not see the washer when I took it apart and I can't tell where it goes in order to put it back together. It is very thin and measures about 5/8 inch with an 11/32 inch hole. Frank Nething

Hi frank this sounds like its a compression washer, you normally find these on the end of the roller to even out any movement from side to side, as you look at the hoover's brush head, it should slip into a groove on one side with the roller...hope t ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Vacuum Philips vision Plus Squeal from seal joinining hose to cleaner. Are there replacement seals available/ How do I order one? [email protected]

Yes there are replacement seals available. check www.trademe.co.nz ...if you dont get some there contact me for further assistance.Hope this solution has been helpful? ... Vacuums

The rubber seal strip inside of the vacuum system on top and on the bottom has started coming off. I was wondering if I could reorder this rubber seal stripping to replace on my system. The model number on my system is #91740. MV 261414/1 is another number that was labeled on the back of machine as well. We ordered it off of QVC and the name of this vacuum system is called, Cook's Essentials's Vacuum Packaging System. Thank you for you time. Look forward to hearing back from you soon.

... Vacuums

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v

I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Broken drum lifter on samsung washer - Samsung ASSY-DRUM LIFTER;B MO - DC97-13901A

... Samsung ASSY-DRUM LIFTER;B MO - DC97-13901A

When I press the botton next to power button in order to activate the bruch for carpet cleaning. The brush does not spin anymore.

HighnTools \015\012posted this solution a while ago. This might be related to your \015\012problem:\015\012 \015\012I \015\012have finally fixed my sister's dyson dc 15 beater bar problem. ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

How do I install the front wheels on a kirby sentria G10D? One of the front wheels broke completely off so I ordered the front wheel shaft assy but I didn't remove the broken one so I am having difficulty with how to put the new one on.

... RTO Vacuums

Where can I order the following parts for my 1952 KENMORE SEWING MACHINE MODEL #117583, SERIAL #48054: : #5107 carbon motor brush (2) #5110 motor brush spring (2) #5111 motor brush spring cap (2) String for starter control lever Pulleys, screw and nut washer to attach string control Best sewing machine ever and still working like new, and I want to keep it that way. Thanks.

... Vacuums

Where can I order a seal pack assembly for a Culligan Estate 3 online?

Call 1-765-452-5553 ... Vacuums

I am using a hoover ultra steam cleaner but the red ball keeps coming to the top . I assume this indicates it is full and ready to empty however it is still empty . The red ball will not stay down in order to operate properly

\015\012Thankyou,\015\012\015\012 The redball indicates that it is full, that is due to the high resistence its suction system is inducing, because it is empty and it still stays up, I would try to turn the power settings a little l ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have the dc 17 animal model and there are no instructions in how to use the attachments,how they connect and so on.I have to assume that this is not an uncommon question considering that the box was completely sealed when purchased. Are there instructions that you can download. IMorales

You can call the Dyson helpline for information on how to fit the attachments. Generally, you can fit them on the wand and the hose (wand - directly on top of the red piece of plastic, hose - take the wand off the back of the vac and press the red bu ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Vacuum cleaner Goodday, I am looking for a vacuum cleaner, carpet washer in one the best on the market and the noice must be soft. I must have 3 quotes. Thank you Annatjie Pretorius 012 365 3363

Try an Electrolux ... Vacuums

How to change f 17 filter kone? i bought the display model and i don't have the instructions. it spits dirt everywhere when i use it, so i assumed there was no filter, ordered f17 filter but now have no idea how to install it or where to???

... Dirt Devil Kone Cordless Bagless Handheld Vacuum - Pink

Took my Miele Solaris canister vac in for repair as it wouldn't turn on. The repairman said to come back the next day for the estimate. I called and he said I needed a new cord reel and it would be $189. I drove to his shop and said I would wait to do it later, that I wasn't ready to spend that much. When I came home, it started right up but has no power and doesn't sound right, the noise of the motor is real soft, not as loud as before. I have this terrible feeling that when we decided not to

When you say 'has no power' do you mean , no suction? He may have left the suction hose of the motor and that's why it sounds different. I would call him back and request that he put the machine back to it's original 'state' as it was when you brough ... Vacuums

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .

Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Bissell Proheat Turbo 2x model 9300. It has stopped spraying at the floor. The hand tools will work so I assume this means the problem is at the base somewhere. I cleaned the nozzles but don't know what to try next. It has always had a problem with dumping too much cleaning solution as well, don't know if this is a contributing factor

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Repairing the idler arm assy model U6445 Windtunnel upright with bag

... Vacuums


First put the gasket on the spacer, thin end to to out, push it down all the way on the motor shaft, then put the nylon washer on, then the fan, metal washer and then the pulley, just snug it, (don't tighten too much just beyond hand tightening). Pu ... Vacuums

I have a very old Greenfield garden tractor, a very early 5hp one. The blade chutch facing has worn completely. I can't source a new facing for it. Any ideas on where i can buy clutch facing material so that i can cut a new one.?? The clutch facing is 150 mm od, 100 mm inside, and 3 to 4 mm thick.

Just a thought, motorcycle shop or transmission shop? ... Vacuums

The Lower body of the Bissell QuickSteamer, water pours out from the body. Solution: I took apart the machine and there is a spring loaded valve with a rubber washer at the bottom. Think of the letter T upside down with the rubber washer on it. The washer stretches over the bottom and the spring creates a leakproof plug and won't allow water to pass till the button on the handle is pressed. This old washer came partially off and allowed water to leak. I purchased from the plumbing dept. a mi

... Bissell Vacuums

I just ordered this part not knowing if it's the 1/4" one i need ! your add don't say

... Craftsman 2823125000 Collet Asy

I ordered an item from L.Cameron on 23rd Sept. Order acknowledged. paypal also acknowledged payment made . Item ordered has not been received, no cash has been taken from my paypal account. Perhaps I have misundertood the procedure. Can you advise? Email number; [email protected] I am not sure what I have to do. Thankyou

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0202 seconds