Having problems with your Vacuums ?

My Kirby beater bar is not turning - Vacuums

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan

Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

My Hoover Platinum LiNX Cordless Stick Vacuum beater bar is not turning. After removing some clogged hair and items...the vacuum cleaner has suction, but the beater bar will not turn. What to do? The belt is still attached and will turn manually.

... Hoover Platinum LiNX Cordless Stick Vacuum

I had a shoelace get stuck in the beater bar. I turned it off, tipped it over and untangled the shoelace from the beater bar. When I plugged it back in the vacuum ran but the beater bar was not turning and there wasn't any suction. Is there a reset switch for the beater bar? Thank you for your help, Janet

Hi Janet. there is a small reset button on the outside of the head next to the brush that you can push to get it to start spinning again. ... Dyson Ball DC24 Bagless Upright Vacuum

I have a dyson DC28 vacuum and the power button flashes on and off and the beater bar quit turning. I turned it over and found some string caught on the beater bar which I removed, but the beater bar still does'nt turn and the power button still flashes on and off. I hope you can give me a solution to this problem.

I had the same symptom with my wife's DC28. The problem was associated with the cam driven height adjustment mechanism. The beater bar must rock freely up and down when pressing on the tabs that the end cam lobes actuate. On ours I found hair and cru ... Dyson DC28 Animal Bagless Upright Vacuum

The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn

The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely

The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

I cannot get my beater bar to turn - Kirby G4 Bagged Upright Vacuum

Manual on how to attach the nozzle - HERE. Or you may watch the video on the bottom of the home page on goodvac.comGood luck,Rocky ... Kirby G4 Bagged Upright Vacuum

My Kirby beater bar is not turning - Vacuums

... Vacuums

My beater bar on my Kenmore 116.25615506 canister vacuum keeps turning on and off when I vacuum rugs. The suction continues, but the beater bar seems to be shorting or whatever. I checked the belts and they look like new. Any suggestions? The rest of the vacuum works fine!

... Kenmore 25512/ 25513 Progressive Canister Vacuum

While vacuuming my carpet, a corner of a throw blanket was sucked into the beater bar. I turned the vacuum off and was able to pull the corner of the throw blanket out without much resistence. I plugged the vacuum in and started it and now the beater bar isn't rotating.

Try pressing the reset button on the nozzle, probably just tripped out the brushroll motor ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being

Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums

I have a central vac. and the beater bar, for the carpet is not turning. the vacuum still sucks but the beater bar doesn't turn. I checked the belt it is fine.

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=818384\015\012Generic problem for all Vacuums\015\012I have a central vac.\015\012Posted by bmiller874 ... Vacuums

My dyson animal is hard to push on carpet - the beater bar is still operational. When I turn off the beater bar and run the vacuum on hardwood the beater bar stops moving, but it still ''rolls'' on the hardwood - it doesn't pull up like it used to. It also seems to not be picking up as well as it used to, although no blockages are present and the filter is clean.

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Kirby Heritage II. Beater bar does not turn. One end rotates freely, but the other sticks, preventing the bar from rotating. No obvious means to disassemble the end of the bar. Is there a way to repair this, or does this require replacement of the beater bar? Did clean the front end assembly, and removed all hair, threads and similar obstructions.

The bearing is bad on the end that turns hard. You will need to purchase a new brush roll assembly. If the roller is older that 4 or 5 years, it should be changed anyway. The brush strips that scrub the carpet loose their strength after many years of ... Vacuums

I have a dyson animal (purple) "the ball" vacuum and now when I push the button to turn off the beater bar it turns off my vacuum. Help?

There is a linkage between the on/off and the beater bar switch that probably has came loose or is broken. It also could be wires shorting out. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My vacuum's power light is flashing and the beater bar will no longer move. It does turn on and have suction, just no movement of the beater bar.

... Dyson DC28 Animal Bagless Upright Vacuum

The beater bar on my Kirby Generation 3 does not turn when it is on. I took it off and cleaned it but I am not sure which way to put beater bar back in. The ways I tried, it still doesn't work.

First - make sure that you are installing it right - see online manual HERE . If you still can not get it working right - issue new ticket and explain in more de ... Kirby Generation 3 Bagged Upright Vacuum

Again, I have a Bissel Model 3760-4. The same problem as everyone else. The beater bar will not turn. Took apart, nothing. Took to vacuum repair shop and they said it is not getting power to the motor to the beater bar. Seems like a fair number of folks are having this same issue. You would think Bissell would come up with a fix, if nothing else to save their reputation. Thanks Diane

... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

I was cleaning the hair from the beater bar, and it popped out with the belt still attached...have tired to put it back in , but the beater bar will not rotate when the vacuum is turned on

When you put it back make sure that the ends of the bar fits exactly in the ends o the box and has to roll smoothly even when you rotate it with your hand when you try this has to be disconnected ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I can't get my vacuum cleaner to run. the beater bar doesn't turn. I've cut off hair and strings that have wound around the beater bar, but I can't figure out how to take off the bottom plastic thing.

... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

I have a windtunnel 2 vacuum. It sucked up a cord that wrapped around the beater bar. Now the bar won't turn. There was no smoke or sign of something burning. The motor still runs and there is suction but no turning. We have it apart but nothing is obvious. What should I check?

Check the actual beater bar for movement. I have seen the plastic melting, and bearings seized under such circumstances. Also I am unsure by your question, but the motor that creates the vacuum (sucking) is different than the motor that spins your ... Vacuums

Bissell 6579-2 bagless vacuum. Beater bar siezed up. motor turns. took bar out, no movement from either end cap on bar.

1. Uing the appropriate sized drift punch, tap out the steel axle rod which passes through the beater drum.2. Each end cap houses a 608ZZ ball brg.3. Check each brg for freedom of smooth rotation. Replace both if either is seized. ... Vacuums

Terrible noise My dyson was working great then started making this horrible noise. I cleaned the bar but noise is still there. I discovered the beater bar went around three passes then froze and started horrible noise again. my husband got the bar turning but after 2 swipes vacuuming it did it again. Can it be fixed or is it time to retire it and buy a new one. Wendy Kiser

That noise is the clutch. A very expensive part and very hard to replace. When a problem with the clutch happens it's generally not worth the time and money to replace.I suggest getting a different type of vacuum, maybe a Miele or Sebo. W ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Beater bar on upright Kenmore Intuition vacuum will not turn.

... Kenmore Vacuums

Dyson vacuum DC17 beater bar won't turn

Sounds like the brushroll motor has gone bad. disassemble the head and check the continuity on the brushroll motor ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3787 seconds