Having problems with your Vacuums ?
LOCATING PARTS FOR HOOVER UPRIGHT
\015 HELLO\015\012 I AM TRYING TO LOCATE A FAN FOR THIS UNIT AND AM GETTING STONEWALLED IN EVERY APPROACH THAT I HAVE TAKEN SO FAR . IN KINGSTON , ONT WHICH IS 45 MIN. AWAY NOBODY CARRIES THE PARTS ANYMORE AND ACCORDING TO THEIR LISTINGS ON THE COMPUTER YOU HAVE TO BUY THE MOTOR AND FAN AS A UNIT WHICH IS PRICED AT ABOUT THE SAME PRICE AS A NEW MACHINE .THIS VACUUM HAS VERY LITTLE USE SO I DO NOT WANT TO DISPOSE OF IT. I SURE COULD USE SOME HELP LOCATING THIS PART. I EMAILED HOOVER CANADA AND DID NOT GET ANY RESPONSE\015\012 THANKS\015\012 WARD\015
What is you rmodel number????
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
LOCATING PARTS FOR HOOVER UPRIGHT
What is you rmodel number???? ... Vacuums
Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest
I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum
VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter
There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums
Too much play in upright part of my Hoover upright wind tunnel
No. The handle release pedal is snapped into the bottom base assembly. Look underneath to check for cracks or damage in this area. this is the most likely issue. If it is, then the base will need to be repalced. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Hoover windtunnel wheel spring location - Hoover U5262-900 / U5260-900 / U5266-900 / U5268-900 EmPower Bagless Upright Vacuum
Hello irishud. Go to searspartsdirect.com\015\012\015\012Enter your model number and you will get the schematics that show you exactly the wheel spring location. Joe\015\012\015\012Thanks for choosing Fixya! ... Hoover U5262-900 / U5260-900 / U5266-900 / U5268-900 EmPower Bagless Upright Vacuum
I am trying to find out a part number for a rubber gasket that goes on the inside of a Hoover Windtunnel Cyclonic Platinum BAgless upright. It is a very thin, light-weight gasket made of rubber that helps seal the filtering tubes. If you know where I can find a parts break down, please advise,,, JON [email protected]
Hi There,\015\012\015\012I'm not sure exactly which part you are asking about, so I went ahead and uploaded the parts schematic of your vacuum cleaner, that will diagram all the parts, and part numbers.\015\012\015\012If you n ... Hoover UH70015 Bagless Upright Cyclonic Vacuum
I have a Hoover 6630-900 bagless upright. The "valve arm rear, part #38719048" broke. I have a repalcement part, but cannot get the spring, frontt and rear arms assembled correctly. Ant hints? Do you have a photo of the assembly on the vac? Thanks, Lee Duncan
... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
Hoover upright has stopped working and tripped the circuit breaker. Where is the fuse located on the hoover ?
Most Hoover uprights do not have fuse. Some canisters doe but it is a thermal shutoff. When the vac overheats and cools down it restarts on its own. You very likly have motor damage, but if lucky you could have an obstruction in the fan causing ... Vacuums
Hoover Model#us445900 diagram parts listing - Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum
... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum
The switch on our Hoover Windtunnel vacuum cleaner is not working. I have located the replacement part on your website...part#Ho-28161067, I've removed the wires from the switch. Is there any trick to actually removing and replacing the switch itself? It seems to be in there rather tight.
No, follow the directions to replacing the switch and you should be good. if you got the kit then splice the wires and replace them with the wires profied and the wire nuts, you should be good. ... Vacuums
Have the empower upright cleaner. belt broke. can not find part #36528-040belt. can find a lot of hoover belts but not this #.Is there another hoover belt that will work on this vac?
No. if the wrong belt you will have problems. This is a common belt for Hoover, it used to be 36528027, but the number changed to the 36528040, also 40201190 is the newest number for this belt. Most repair vacuum repair shops should have this belt. ... Vacuums
Hoover Upright Part # Help
The difference is that the late model was has extra support on it then the earier one. Most likely either would work, but the late one is better. The 36433111 is the earlier version. ... Vacuums
Hoover U5280-900 upright bagless vacuum twin chamber has a broken slider (switch) to go from tools to floor and carpet--what is the part called?? Indicator knob or cam activator?? where to order it??
... Hoover Windtunnel Supreme U5280-900 Upright Vacuum
Parts diagram for floormate 3000 - Hoover Floormate H3000 Upright Wet/Dry Vacuum
You can find the parts and parts diagram schematic on the link below.H3000 Link ... Hoover Floormate H3000 Upright Wet/Dry Vacuum
Hoover self propelled bagged windtunnel upright model #U6435-900...how do you remove the green plastic shell cover to get to the part that secures the v belt...we need to secure the bolt and cannot get the area. Brushes and transmission wheel not rotating? thanks
Greetings from GoVacuum,\015\012\015\012Here's a great video repair tutorial that we've put together to try and help you with the repair on your Hoover WindTunnel. I hope that this helps you with your repair. If you found this solution ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
My hoover windtunnel is not picking anything up all of a sudden. Also the roller underneith is not spinning. I've replaced filters and the attachment part is working fine, just when it's in the upright position it won't pick anything up. It also doesn't seem to be self propelled anylonger either. It use to **** everything up, including the dog. Please help!
The belt that drives the brush roll has broken. That's why it doesn't pick up and why it doesn't pull itself forwards. Check the User Manual (download from Hoover website if necessary) for information on replacing the belt. Good luck! ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
The handle release lever (Part N. 38434-021) on my Hoover WindTunnel upright vacuum (uses Y bags) broke. How do I install the replacement release lever (pedal) that I purchased?
You can buy Hoover Handle Release Lever 38434-021 at \015\012http://partsreadyonline.com/item.php?ItemID=798 ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
Need parts manual, have a bad bearing - Hoover F7458-900 Upright Vacuum
Www.espares.com Thats where you will get your parts. ... Hoover F7458-900 Upright Vacuum
While putting on a new belt for my Turbo 4000 Hoover upright vacum cleaner, the parts for the height adjustment (slide bar)fell apart. I'm hoping that you might have a diagram or detail instructions on how to put together again. Thank you
My girlfriend has a Hoover upright vacuum, Mdl. # U4645-930. I need a belt for the brush and a new bulb and am having trouble finding the correct part numbers so I can pick one up locally. Can you help?
I checked with Hoover and they said the part number for the belt is #38528040, for the bulb #27313101, and they also included a part number for something called an agitator #48414081. Not sure if this is required to replace one of the other parts. ... Hoover Windtunnel Turbo Power U4645-930 Vacuum
Hoover tempo upright is clogged. I can only vac for a few minutes, then I have to unplug it and turn it over and clean out the under part under the roller. It is totally stuffed with dirt and dust and carpet fibers. I have a new bag in. It is like it is clogged up inbetween the bag and the roller. Also gets clogged when using the hose. It is maybe a year old. How can I take it apart and unclog it?
Disconnect the hose and head and wands. Drop a quarter thru the hose, the handle sometimes clogs. peer thru the wands and inspect the elbow on the head for blockage as well ... Vacuums
I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.
Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums
I need a nozzle adjustment lever and cam kit for a Hoover upright U5432-900. This the part that adjusts the front wheels for different types of flooring.
... Hoover U5432-900 WindTunnel Plus Bagged Upright Vacuum
Vaccum cleaner, (hoover upright) needs new belt, but i can't figure out where it's located.....yes, i'm a woman...lol thank you..
Turn Vac over, remove the plate covering the brush roll, then you can get to the belt and brushroll. ... Vacuums
I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums