Having problems with your Vacuums ?
Vac won't turn on and the beater bar won't turn.
\015 I had my first vac for 3 months before having to take it back to Home Depot and exchange it for another. I am having the same problem with this vac. The vac will not start until I remove and replace the dirt collector container several times and the beater bar will not come on.\015
If you are having the same problem, then maybe there is something that you aren't doing right. But you do have a years warranty on what ever brand and model this is, take it in for warranty repair.
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I have a central vac. and the beater bar, for the carpet is not turning. the vacuum still sucks but the beater bar doesn't turn. I checked the belt it is fine.
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=818384\015\012Generic problem for all Vacuums\015\012I have a central vac.\015\012Posted by bmiller874 ... Vacuums
Vac won't turn on and the beater bar won't turn.
If you are having the same problem, then maybe there is something that you aren't doing right. But you do have a years warranty on what ever brand and model this is, take it in for warranty repair. ... Vacuums
My beater bar is struggling to turn. actually, it appears as though it is the motor that is struggling, as it slows down when going against the pile and the motor labours so much that it frequently fails to turn the bar until i lift it up again. the belt appears ok, and it is clean of hair etc. it is a 5 year old beam central vac. thanks, D
... Beam Industries 875 Classic Central System Vacuum
I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile
... Eureka Smartvac 4870 Bagged Upright Vacuum
I had a shoelace get stuck in the beater bar. I turned it off, tipped it over and untangled the shoelace from the beater bar. When I plugged it back in the vacuum ran but the beater bar was not turning and there wasn't any suction. Is there a reset switch for the beater bar? Thank you for your help, Janet
Hi Janet. there is a small reset button on the outside of the head next to the brush that you can push to get it to start spinning again. ... Dyson Ball DC24 Bagless Upright Vacuum
I have a dyson DC28 vacuum and the power button flashes on and off and the beater bar quit turning. I turned it over and found some string caught on the beater bar which I removed, but the beater bar still does'nt turn and the power button still flashes on and off. I hope you can give me a solution to this problem.
I had the same symptom with my wife's DC28. The problem was associated with the cam driven height adjustment mechanism. The beater bar must rock freely up and down when pressing on the tabs that the end cam lobes actuate. On ours I found hair and cru ... Dyson DC28 Animal Bagless Upright Vacuum
The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn
The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums
I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely
The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums
The beater bar wont turn and is breaking my belts
You might have the wrong belt size. ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum
I have a hayden premier supervac central vac system, while working on the switch in for the beater bar, the actual unit has turned off, the green light is no longer lit, is there a fuse on it somewhere or a reset button, i have tried unplugging it and replugging it in, but can not seem to get it to power up now?
Should be a reset on the main unit near the top ... Vacuums
Dyson dc25 beater bar wont turn - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Eureka The Boss Smart Vac, beater bar stops turning when you use it on carpet
It is a simple fix that you need. Your belt needs to be replaced. After a period of time, the belt stretches to the point where it is still strong enough to spin the brush when you have the machine upside down to look at it, but when you put the mac ... Eureka Vacuums
Hello. i only have one arm and am trying to figure out why my beater bar wont turn on my dyson dc14. the belt smells a little too. thanx, trixie
Sounds like the beater bar is frozen in place. This sometimes happens when the ends of the bar become stuck in the holders.\015\012The solution is to remove the beater bar and clean the small holders on each end removing any debris that has built up ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
The vacuum turns on but wont run smells like burning rubber I took the bottom off and the belts dont appear to be broken but the one connected to beater bar seems like it may be loose
Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=542493\015\012Generic problem for all Vacuums\015\012The vacuum turns on but\015\012Posted by mmetcalf on Apr 24 ... Vacuums
I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan
Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum
My Dyson DC17 beater bar motor works intermittedly. I have to almost whack it on the floor to turn it on and then shuts off again. I have checked the belt and it is fine, also have checked for blockages. The switch to turn the beater bar on or off will not work when the beater bar motor is off. the suction is fine though.
Buy a Kenmore for less money ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?
My Hoover Platinum LiNX Cordless Stick Vacuum beater bar is not turning. After removing some clogged hair and items...the vacuum cleaner has suction, but the beater bar will not turn. What to do? The belt is still attached and will turn manually.
... Hoover Platinum LiNX Cordless Stick Vacuum
Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?
Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Beater bar will not turn, think belt is broken, but do not know
The model number of the powerhead would be helpful - usually there is plastic cover with a lens for the light, push inward on both sides and the cover will pop offthere are two screws under that OR, there are two screws on the underside of the unit - ... Kenmore 25512/ 25513 Progressive Canister Vacuum
The beater bar isn,t turning on my panasonic MC-GC467 IS THE BEATER BAR SUPPOSE TO TURN
Ya, you probably need to replace the belt. You can get replacements here:Replacement Vacuum Belts ... Panasonic Kenmore Canister Vacuum Vacuum
I sucked up a piece of fabric and turned it off ASAP. Now the beater bar won't work, but the beater bar does turn. Help!
If the clothe is jammed in the power head you will need to clear it. Have the unit unplugged and manually rotate the beater bar to work the jammed material out. Sometimes a pair of pliers helps to grip the material while turning the beater bar. If th ... Vacuums
The beater bar on my dyson DC28 is not turning when it is placed on the carpet. If you lift the sweeper up the beater bar will turn but then when you place it back down on the floor it stops.
... Dyson DC28 Animal Bagless Upright Vacuum
Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest
I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum
I have a Bissell 3920 and the beater bar only turns when I'm pulling the vacuum.How do you get the end caps off of the beater bar to clean it out? This has happened before when it was under warranty and I was told to remove caps and clean frequently.I am afraid prying them off will break the vacuum.It also has very low suction and I have cleaned the filters and the belt is fine.Will cleaning the inside of the beater bar fix my problem?
... Bissell 3920 Cyclonic Pet Hair Eraser Vacuum