Having problems with your Vacuums ?

Hoover vhd replace drum bearings - Vacuums


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover vhd replace drum bearings - Vacuums


... Vacuums

Replace the bearing on a hoover hwb280 - Vacuums


... Vacuums

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.


... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t


... Hoover Vacuums

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel


The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

Hello, I have a Hoover quadraflex Powermatic central vacuum system Model # s8099-031 that requires a new replacement 35 ft hose...I have contacted Hoover and they do not know where to buy a replacement hose for this model. I live in Canada. Any idea where I can get a replacement hose for this system? Thanks kindly, Tammy


Tammy, no info re your location, so I''l try this.Your Hoover hose is shot because it was made of rubber.There are new swivel handled, tangle proof lighter hoses made of vinyl which will last much longer and can be adapted to the old Hoover hea ... Vacuums

I have bought new Hoover bags on two occasions. The first spares I bought were the Xxxl variety and I didn't think they fitted that well. The next spares I bought were the type g megafilt. I still feel like they do not fit that well and the suction power on the vacuum is not as good. I'm I buying the correct replacements? I followed the guidelines on the Hoover bags the vacuum came with. These were printed as the right bags to buy. I only have the vacuum around a year and thought it was brillian


... Bosch BSG71310UC Bagged Canister Vacuum

Power nozzle of my S3670 does not work (vacuum itself does work), the headlight bulb in the nozzle is broken. This happened in the past several times - we would bring the vacuum to service center - I don't know what they did other than replacing the bulb. I decided to go to ACE and buy replacement bulb myself, replaced the one in the nozzle - this did not fix the problem. I don't see any fuzes or anything in the nozzle. However, the manuals says to "Use only HOOVER part no. 27317307, which is a


... Hoover S3670 Bagged Canister Vacuum

Hoover U5344-950 My Hoover vacuum is a nightmare! I have had nothing but problems with it since day 1. The powerhead stops working if you try to lower the handle to vacuum. I took it in to be serviced and was told it sat on the shelf for too long in the store and it warped the belt...so it was replaced. Got it home, it worked the first time I tried it, then went right back to no powerhead working and as a bonus it is giving off a nasty smell like it is going to blow up! It now gets really hot to


... Hoover U5344-900 WidePath Vacuum

How to replace hoover u5071-930 vacuum belt - Hoover U5227-930 Elite Upright Vacuum


... Hoover U5227-930 Elite Upright Vacuum

Replacing belts on U3109 hoover vacuum - Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Replace motor hoover windtunnel - Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum


... Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum

I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.


... Vacuums

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr


Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

How to replace power cord on Hoover WindTunnel upright vacuum


The aforementioned solutions probably never even attempted this fix on this model. The handle does NOT need to come off. but the 5 screws on the front housing DO: 2 above the light and 3 below it. Then to get the colored housing off you need to acc ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

How to remove the bag housing from the handle in order to replace the power cord on a Hoover vacuum U5209-930


... Hoover Vacuums

When I sart to run my bagless vacuum, it runs for a second and then shuts off. I replaced the belt and the filter. The repairman told me that on bagless vaccuums, the motor and bearings get clogged w


Take the brush roller off and on the ends are the bearing caps.try to take those off and clean the bearings ,carpet strands and hair will cause that.after you do that make sure the roller turns freely if not then the bearings might be bad and if that ... Vacuums

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef


Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a


Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

Belt replacement in Hoover Sprint upright vacuum


Take the screws off the bottom. Use a flat head press down snap the bottom over off. The housing on top you gotta snap off. ... Vacuums

How to replace switch on a Hoover WindTunnel twin chamber bagless vacuum


... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

How to replace the auto rewind button on Hoover canister vacuum.


116-...... usually indicates a Sears/ Kenmore model vac Please clarify ... Hoover Vacuums

Replace on/off switch on hoover vacuum


My wife picked one up on the side of the road that someone had tossed. The power switch would not turn off. I took the two bolts out of the top part of the handle, and then removed the screws along the back. This will remove the required panels to ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Need to replace power cord on Hoover vacuum.


Remove the dirt container and look for screws. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

The switch on our Hoover Windtunnel vacuum cleaner is not working. I have located the replacement part on your website...part#Ho-28161067, I've removed the wires from the switch. Is there any trick to actually removing and replacing the switch itself? It seems to be in there rather tight.


No, follow the directions to replacing the switch and you should be good. if you got the kit then splice the wires and replace them with the wires profied and the wire nuts, you should be good. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1289 seconds