Having problems with your Vacuums ?

I require a new drive belt for my upright vacuum cleaner


Answers :

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=698244
\015\012Generic problem for all Vacuums
\015\012I require a new drive
\015\012Posted by martiy on Jun 23, 2008
\015\012I require a new drive belt for my upright vacuum cleaner
\015\012
\015\012
\015\012Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. In order to change your belt I would need to know the brand name and the model # in order to give you the correct information to change your belt, so a little bit more information needed as to what you have and then I can direct you in the belt change. Normally there are screws in the bottom of the vacuum and once you remove the screws or clips you can either change it from the bottom or the top cover will lift off and then you can get @ the belt from the top. The average and recommended belt change for a flat belt is every 4 to 6 months and if you have a geared belt it is once a year for the best cleaning. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

\015\012Thanks, Don the Vac Man
Go Ahead. Use Us.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I require a new drive belt for my upright vacuum cleaner


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=698244\015\012Generic problem for all Vacuums\015\012I require a new drive\015\012Posted by martiy on J ... Vacuums

VAX UPRIGHT VACUUM CLEANER V91-P2/HOW TO REMOVE TOP COVER TO REPLACE DRIVE BELT.


... Vacuums

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a


Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

I have a Zanussi 1700W bagless upright vacuum cleaner which keeps cutting out after about 5/10 mins use. I had to replace the rubber drive belt which snapped not long after purchasing and it was fine for a while, but now its just keeps cutting out after a small amount of use. Nothing wrong with belt which is still intact so we don't know what the problem is. It's a great cleaner otherwise - but it's driving us mad!! Please help!


... Vacuums

I have the Bissell upright cleanview bagless vacuum cleaner. My belt broke and someone else took it off. I bought a new belt but do not know where it goes on the cleaner. Please help


Easy to do. Unplug the vac. Turn the vacuum over and look for three finger latches on the bottom behind the brushes. Unlatch these and pull the faceplate off. Then, grab one side of the brush and pull straight up (they just sit in grooves on the ... Bissell CleanView 3596 Bagless Upright Vacuum

I replaced the agitator bar drive belt on a Hoover Model U6432-900 upright vacuum cleaner, but it just slips when the drive wheel is spinning. Is there an adjustment I need to make? I don't see any adjustment spots.


You probably should have replaced the flat belt(38528035) also. But the drive belt has a idler wheel(#13) to engage it, is it riding on the belt, if not if may have jammed to one side and able to spring up against the V belt. It could have broke al ... Vacuums

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t


The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

Drive belt keeps breaking on hoover windtunnel vacuum. Drive belt won't turn the agitator. Belt is new. Small belt is new. Agitator is new.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

CANT FIGURE HOW TO INSTAL NEW BRUSH BELT - Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum


Body {\015\012\011background: #FFFFFF;\015\012\011margin: 0px;\015\012\011padding: 4px;\015\012\011font-family: arial, verdana, sans-serif;\015\012\011font-size: 10pt;\015\012}\015\012p {\015\012\011margin:0px;\015\012\011padding:0px;\015\012}\015\01 ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I just bought a good Sears Kenmore Progressive 300 upright vacuum (116.38812891) today at a garage sale for five bucks. I left my relic Electrolux with the new owners of my former home during a recent relocation. In the interim I bought a Bissel 3750H which I do not care for, and borrowed a Eureka 7685 AU which performs somewhat better. I cleaned up the Kenmore, and though it seems to run well, noticed the drive belt is showing signs of degeneration. I would like to replace it, but was unable t


... Vacuums

How to fit new drive belt - Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum


First take off the cover on the left side oif the top cover, then turn it over, remove the screw holding the red lock and pull the cap and brush roll out, remove the cap, remove the cogged belt, then you can put the new pump belt thru that slot, put ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

How to fit a new drive belt - Dyson DC07 Bagless Upright Cyclonic Vacuum


Hi,\015\012\015\012There are different models of DC07 and the guide below is for the "standard" model. There are some slight variations on different DC07 models, but this should be more or less the same for all of them.\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hello. I have an electrolux glider upright bagless vacuum cleaner (UK model) who's brushes do not rotate any more. I'm guessing that I need to replace the drive belt but I have no idea where to start. I would appreciate any tips. thanks


Hello! There are two solutions to this as the Glider model you speak of could be the more old fashioned type where screws on the bottom foot plate (ie where the spinning brush sits) have to be undone in order to get to the drive belt.\015\012 ... Electrolux Vacuums

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430


Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o


I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

The belt on my vacuum cleaner model 6596 bissel powerforce bagless turbo keeps breaking. As soon as I put on a new belt and start it up the belt snaps. It is the durabelt meant for this vacuum model. Also, my son has been having the same problem with his. He has the same model and same belt. This problem is occurring even after a thourough cleaning.


I would guess you aren't centering the belt correctly, thus it's edge is caught between the brush and another solid object, causing the breakage.\015\012When you get the belt on the the brush and the brush back in place, turn the brush a few ti ... Bissell 6596 Bagless Upright Vacuum

Belt drive Not only do I need a PN for the drive belt on the Panasonic MC-V7395 Vacuum Cleaner, I've noticed that there are problems with the belt breaking. Can someone also explain the proper way to install the belt over and around the motor spindles and any other information that may help. Thank you.


Http://www.partstore.com/Model/Matsushita/Panasonic/MCV7395.aspx?SearchTerm=True ... Panasonic MC-V7395 Vacuum

Have Hoover Wind Tunnel Sel Propelled vacuum. Had to put on new drive belt. Turn on unit and drive belt slides off the drive spindle.


Look for excessive wear on the unit around the pulleys and their brackets that hold them in place. It sounds like something is just worn out and the belt is either slipping because it is not tight enough or because something is not aligned straight. ... Vacuums

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.


You need a new belt. ... Vacuums

New Eureka vacuum cleaner belt keeps slipping off


You may have a bad brush roll, part #61250-1, or the base itself has a problem and isn't letting the brush roll sit straight so it can be in alignment. ... Vacuums

My cleaner ( Oreck 40th Anniversary, XL2 Ultra) several years old, and I love it. My questin, is there a reset button? Vacuum just quit....no noise, sputtering, smell, nothing, just stopped while running cleaner. New bag, new belt. Any ideas?


... Oreck Vacuums

Vacuum belt keeps coming off. Need instructions on how to change belt on Panasonic mc-6955 upright vacuum cleaner.


... Vacuums

Panasonic mc-e4113 Upright vacuum. The belt that drives the brush in front is broken I have found a spare for this but there seems to be a pulley missing on the main drive shaft that the belt needs to fit on. I can't believe that there wouldn't be one? Can anyone tell me if this is the case and if so where I can get one from. Many thanks Sean


... Panasonic Vacuums

Drive belt on upright bagless cleaner


If its like mine there is a rod that comes out f the moter usually on the upper left of the power head put t the belt around that and then slip the belt over the beater bar. Then replace the beater bar. You will have to pull a little to stretch ... Bosch Vacuums

Hoover upright self-propelled drive vacuum cleaner u6331-93 will not self-propel


Here is a video how to fix ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1019 seconds