Having problems with your Vacuums ?

Locate the belt to the pump - Vacuums


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Locate the belt to the pump - Vacuums


... Vacuums

How to check the location of the pump belt? - Bissell 1699 ProHeat Clear View Upright Steam Vacuum


Take off belt cover on the left side of the top cover, turn cleaner over, take out screw from red lock and remove, pull cap and brush roll out, unhook the cogged belt, then you can replace the pump belt thru that opening. Put belt over the pump pull ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Looking for new belt for my electrolux guardian canister vacuum power nozzle marked model n106m . have been unasble to locate an appropriate belt replacement. Any suggestions?


This company is now known as Aerus. If you can't find their listing in the local yellow pages, follow the instructions on the folloing site.\015\012\015\012 ... Electrolux Guardian Bagged Canister Vacuum

I dont know where my Vacuum belt is located? - Eureka 4700A Maxima Bagless Upright Vacuum


The link below is the manual it will give you step by step instructions on page 19 how to replace belt and brushbar ..http://dl.owneriq.net/b/b7517422-db37- ... Eureka 4700A Maxima Bagless Upright Vacuum

FAN PROBLEM??? good morning! my vacuum smells like burnt rubber (fan perhaps) but I can't find how to get into main part of the vacuum. it's just very rounded with no latches or screws to get inside where the motor, belts and fans would be located. can you help me? thank you


There isn't any belts, and the fan wouldn't be rubber, so not sure what you are smelling. Maybe this picture will help you.\015\012\015\012 ... Bissell 6700 Butler Revolution Bagged Canister Vacuum

Belt how do u locate and change the vacuum belt


Look underneath where the brush roller is located. The brush roller is removed to replace the belt. The new belt is installed on the motor shaft and the brush roller then the brush roller is reinstalled ... Eureka Whirlwind 4481 Upright Vacuum

My bissell powersteamer model 1695 does not spray enough water out. Hardly anything will come out of the handheld attachment either, just a few drips. With the floor unit, it appears the only water coming out is a result of gravity when the control is squeezed. Nothing appears to be plugged up with debrie or deposits. There does not appear to be any kind of drive belt for the pump as it seems to operate off the main vacuum motor. Any ideas?


Hi, my name is John I will do my best to assist you.\015\012\015\012Referring to this ... Bissell 1695 PowerSteamer Vacuum

Hello i own the bissle proheat steamer it turns on but no water or soap or suction from floor or the utensiles ive taken the take off the back to scope out anything that could be in the way but dont see anything the motor is making that clogged vacume noise witch makes me believe something could be stuck somewhere in it but it could also be no water is getting to the pump or despencer but the brissels still work belt for that is good where would i be best to check and where is the location of th


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Replacing a pump belt - Bissell Vacuums


... Bissell Vacuums

Where is the belt located? - Riccar 8955 Upright Vacuum


The "belt" is normally the drive device that turns the beater brush found on the bottom front of the vacuum. Its purpose is to beat the rug and cause dirt and debris to rise up from the carpeting and be sucked into the vacuum.\015\012If the belt is ... Riccar 8955 Upright Vacuum

Belt broke cannot locate how to open vacuum and replace


... Vacuums

How do I install the timing belt on my Hoover Savvy Vacuum? Modle # u8174-900 Where is it located?


Http://www.vacshopusa.com/hoover_savvy.htm\015\012This is a parts schematic for your hoover savvy. You have to take off the brush guard on the bottom and ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

Where is the belt located on the shark vacuum cleaner


It should be on the bottom. Remove the cover plate on the bottom and it should be under there. ... Vacuums

Where is the belt located - Eureka 3276AZ Pet Lover Bagless Upright Vacuum


... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

The belt on my bissell 3065 power partner vacuum came off. i looped it around the post located under the roller but it just fell off again. how can i get it to stay on? this vac is 10 years old.


... Bissell 3065 Power Partner Vacuum

I have a Eureka Contour model 2900 type A upright vacuum, the roller works fine nothing clogged, took it apart motor blade is free of debris, no suction from tube and blasts OUT air from the front HEPA filter location. New bag, New belt, nothing in hose.any clues as to why this can be happenning? Air should not be blasting out of the HEPA filter.


Even with your explanation,it seems the hose is clogged.Try taking the hose off,then blow through it or pour water through it.If this doesn't do it,make sure the suction canals are going to the proper areas. ... Eureka 2900A / 2901A Contour Bagged Upright Vacuum

I have a Euro Pro canister EP754 vacuum that runs HOWEVER the main floor attatchment brushes wont turn. Does this require a new belt? And where is it located?


... Euro-Pro Canister EP754 Bagged Vacuum

The brushes on my new healthy home vacuum wont rotate when the machine is turned on how do i access the belt location


If you turn the vacuum over so you can see the brush roll, there is a brush cover that is held on by (4) screws. Remove those screws and the base plate cover will come off. With the base plate cover off you can access the roller brush an belt. If you ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

There is no suction when the Eureka model 7685 is turned on. Is there an Air filter? If so, where is it located? The belt turns slowly when the vacuum is turned on. Is that normal?


No you vacuum tub is clogged. Shut off machine and remove hose where attachments go. Use a long handled kitchen appliance like a spaghetti stir to work the jam back and forth. You will be amazed at what comes out. Then remov ... Eureka 4874 Bagged Upright Vacuum

My Oreck XL 9100HA started smoking (white smoke) when I vacuumed. There is a burning rubber smell. How do I check/change (if appropriate) the belt? I have no User manual, nor can I locate one on the Oreck site. The bag is a new one. The vaccuum had been picking up, though not at its best strength.


It sounds like the belt has been damaged. You can get another belt from yoru local Oreck store. You can even take it in to the store to show them what happened. Purchase another belt and replace it. (It was very easy when I did this, so hopefully ... Oreck XL Ultra Bagged Upright Vacuum

I bought a Clean Broom Electric Co., Model #CBU_5 (SKU# 7986628) Vacuum Cleaner 31CX E 255344. I have need of the following parts 2 belts and brush bearing seals. How do I locate these parts or to find them to purchase them. Thank you for any assistance you can give Tom Freer [email protected] Manufacture Date 0906


I need a screw on filter for model cb9191j-10a vacuum from clean broom electric company. ... Vacuums

How to change pump belt on bissell pro heat - Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum


First take off the cover on the left side oif the top cover, then turn it over, remove the screw holding the red lock and pull the cap and brush roll out, remove the cap, remove the cogged belt, then you can put the new pump belt thru that slot, put ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I cannot locate a store in Nashville TN that carries a Royal Dirt Devil Vacuum style 12 belt. Can you?


Try a walmart store ... Vacuums

Where is the belt located for everstar vacuum cleaner model vc9550 so i can replace it


... Vacuums

Where is the belt located? - Euro-Pro NV31 Infinity Vacuum


See the schamtic below:God bless you ... Euro-Pro NV31 Infinity Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0700 seconds