Having problems with your Vacuums ?

I have a vax swift Hoover burning smell coming out of the bottom

\015 Burning smell coming out of the bottom of Hoover\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a vax swift Hoover burning smell coming out of the bottom


... Vacuums

Vax hoover bagless, there is a burning smell coming from it


Most common burning smell is the belt in the power nozzle. check & replace. ... Hoover S3639 WindTunnel Bagged Canister Vacuum

My hoover 2000w pets cyclonic stopped working, there is a burn smell coming out off it


... Hoover Vacuums

I was using my Henry Hoover as usual. When i sucked up quite a fair sized puddle of water. The hoover instantly cut out and a strange burning smell was coming from it. Would this be the fuse, motor etc ? Or would it be worth my while just replacing the entire hoover ?


Hi. I have to wonder why anyone would **** up a puddle of water with a dry vacuum cleaner (with no earth lead). I realise that your question may simply be a joke, but if you are serious, I think it is probably fair to assume that it is now dead and p ... Vacuums

Burning smell coming out while using a Hoover's upright vaccum cleaner (model U6434900). Replaced both flat and v-belt. The problem appears to be coming from near the motor area. The manual does not provide any information on how to reach that area. Any help will be appreciated.


Took it to a manufacturer's repair center. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Vax 2300 vax v-2300 brush is not turning so changed belt snapped as soon as i put hoover on and getting burning smell put another belt on same again and brushes still not moving only 4 months old


If the roller brush cannot be rotated easily by hand, it is likely that debris is jammed inside the end caps.Make note of the direction arrows on the end caps as you remove the roller brush. You will need to know this for reinstallation. The end caps ... Vacuums

Vax 6131t Burning smell coming from Vax 6131t


... Vacuums

Burning smell coming from hoover canister windtunnel vac


... Hoover S3639 WindTunnel Bagged Canister Vacuum

Drive went out on my Hoover Steam Vac Shampooer and brushes won't turn plus there's a burning smell coming from it. Only used it 6 times - bought it in March - 2008.


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=761326\015\012Generic problem for all Vacuums\015\012Drive went out on my\015\012Posted by buster_lls o ... Vacuums

Hoover smells of burning - VAX Appliances Vacuums


... VAX Appliances Vacuums

How do I open my vax mach3 powerhead to replace the belt.. there is a burning smell when I use the Hoover. I'm assuming this is the problem???


... Vacuums

Burning smell coming from motorwhile running - Hoover Steam Vac Dual V w/ SpinScrub Vacuum


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

It smells like something is burning and then I saw smoke coming from the bottom, where the roller brush is.


That means that the belt is very worn and it is slipping on the motor. You need to replace the belt. Here is a link to the belts you need and a manual you can view with instructions: ... Eureka Uno 2998AZ Bagless Upright Vacuum

I have Hoover whisper Cyclonic. I just opend beacuse it was showing Clogged. I removed all dirt etc from the belt and now roller are not moving round and the smell of burning is coming due to rubber not moving on the roller. I looked at the manual which tells me in cased on roller being Jamed if need to use the stich to reset. I looked all over could not find the switch. Can you guys help me please.


... Hoover Sh40080 Zen Whisper Bagless Multi-Cyclonic Canister Vacuum

Burned smell hi, I have used my hoover 4 times and is starting to smell as something burned, I checked the troobleshouting part of the owner manual and it says that check the belt, I already did that and everything is ok I used the hoover again and still smelling bad and start to work very slow I better shut off it.. what could I do??


If the motor slowed down this would indicate a bad motor. not cost effective on this model to replace unless under warranty. it is not uncommon these days to see a motor go bad every now and then.\015\012\015\012What are the first 4 digit ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

Burning Smell coming from the moter


This could be a motor problem. There is always a slight blue arcing that occurs when an electrical motor runs and can be visible through the exhaust vent, but any excessive arcing indicates a problem. If the carbon brushes are sticking, this will cau ... Hoover U5262-900 / U5260-900 / U5266-900 / U5268-900 EmPower Bagless Upright Vacuum

Burning smell There is a burning smell when I run my Kirby Ultimate G.  The smell seems to be coming from the belt.  I looked at the brushes and they are spinning so the belt is working.  the Post on the vacuum is getting very hot not sure if that is normal.  What is causing this?


Unlock the sweeper brushes and take them out. on each end is a cup bearing and should be free of debris.then check around and under the belt and likely there is debris wrapped around it.the post is getting hot as your pulling too much of ... Kirby Ultimate G Bagged Upright Vacuum

Burning smell coming from vacuum


Use a penny to turn the 2 screws on top a quater turn then fold down the vacuum and lift up the cover and you will have access to the belt. Clean the small hepa filter with soapy water. their may be 2 of them. The cannnister filters need to be shaken ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

My numatic Hoover is brilliant but it smells what part needs changing? It's not a burning smell, but a musky almost cabbage smell?


It could be the sponge filters or the dust partition that need replacing. But it might also be coming from the motor, best bet is to get it checked out. ... Numatic Henry Bagged Canister Vacuum

Burning smell how do I get the bottom section apart to clean it out- burning smell when i have the spin brushes turned on. Any help would be appreciated cause I love this machine and hubby told me it couldn't be taken apart to be fixed. Thank you.


The bottom doesn't come apart. you have to remove the top cover to get to any components. But if you have a burning smell, then it is probably ther motor and would have to be replaced. Motors cost anywhere from $70 to $90. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Burning smell I had purchased a hoover widepath tempo vacuum two years ago and recently when I turn it on to vacuum it smells like something is burning.


The belt needs changed. its slipping. make sure its not clogged with carpet or string ect. first. if not buy a belt at walmart. in stock... ... Hoover Tempo Widepath Upright Vacuum - Blue

Hoover Max Extract Dual V has a burning smell, what could this be?


... Vacuums

Sewing machine Guru needed ;) Elna Grasshopper (new to me) circa 1950 The light works, but there was no hummm when knee pedal engaged. I have the motor out, and it is very stiff to turn. I'm at a total loss when it comes to motors and electricity. It doesn't smell burned, doesn't smell at all beyond normal machine smells. (Yes, I made detailed notes and diagrams as I took said motor out!) One other note. The long thing which my husband said might be a capacitor -- it looks like


I just purchased a fairly tidy Elna 'Grasshopper' sewing machine (1951) with the same leaking capacitor problem. I carefully removed the capacitor for examination. It is actually three capacitors in one - no chance of a direct modern replacement, but ... Vacuums

Hi The band snapped the other day on my Vax Swift Turbo upright hoover and i got a new band from a Hoover repair centre. (Im assuming the bloke sold me the correct band). Was tight to go on. And it seemed ok. However, after switching on the band snapped immediately. Kinda burnt as well (at the point it snapped). Any ideas as to what the problem is here? The hoover is roughly 2 years old and used around 3 times per week. thanks Mike


Sounds like the brush roll is bad. Did you check the ends to make sure they turn freely? If not, replace it. ... Vacuums

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi


Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0610 seconds