Having problems with your Vacuums ?

Snapping belt The belt broke in my Eureka maxima model 4700 I replaced it and the brush did not move, and the belt just snapped again. What might be causing this?


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Snapping belt The belt broke in my Eureka maxima model 4700 I replaced it and the brush did not move, and the belt just snapped again. What might be causing this?


... Vacuums

Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught  on the metal pole?


Check the Idler Pulley part Number 43241004 (Item 13 in the IPB)http://64.49.205.183/v/u6451900.pdf ... Vacuums

Vax 2300 vax v-2300 brush is not turning so changed belt snapped as soon as i put hoover on and getting burning smell put another belt on same again and brushes still not moving only 4 months old


If the roller brush cannot be rotated easily by hand, it is likely that debris is jammed inside the end caps.Make note of the direction arrows on the end caps as you remove the roller brush. You will need to know this for reinstallation. The end caps ... Vacuums

I have a bissell proheat carpet cleaner purchased in 4-18-2005 for $169.99 from kohls I have used it 6 times and the last time the brushes would not move cause the belt was broken and the end of the pump pulley which is plastic broke off so I reorder the pump unit and 2 new belts and now I see you have sent me a exact pump but the end that broke off that the belt rides on is made of steel or aluminum much strong piece of equipment I want to know if there was a recall for the machine due to mecha


I've owned my Bissell for over 5 years now & LOVE it! Even after vacuuming It pulls up tons of dog hair I never realized was there! I am having a similar problem, but I caused it myself & think maybe you may have the same problem, cross you ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have a dyson dc24 and the brush does not rotate anymore. I think the belt might have snapped. How can I open the casing to determine if the belt has broke?


... Dyson Vacuums

I cleaned out the hose and removed brush to clean and checked belt. Everything seems to work but will not pick up or suction on carpet. The hose is totally clear from clogs. I can see the floor from one end to the other. What am I missing that might be causing lack of suction?


Hi troupdavid,I see that your Vacuum is having issues with it suction, you mentioned that you took it a part to clean it, see steps below.\015\012\015\012Check if everything is inserted prope ... Hoover Tempo Widepath Upright Vacuum - Blue

I have a Kirby G series diamond edition. There seems to be no suction when I turn on the vaccum. The bag inflates, but the roller does not turn. It has a new belt and the roller brush is clean. Any suggestion on what I might do to increase the suction and get the roller bar moving?


THE IMPELLER LOOKS SHOT.. 25 QUID FOR NEW ONE,,LIFT THE LID AND TURN THE ROUND PIN AND CHECK FOR RIDGES ROUND THE WHITE IMPELLER,,IF NONE THERE THATS IT,, HAPPEND TO ME TEN MINS TO FIX GEORGE ... Kirby Ultimate G Bagged Upright Vacuum

Dyson dc04 drive belt keeps snapping have put 2 new ones on a made sure it was on shaft fully and brush did move before tunring on


... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum

Have model 3576-6 Bissell Cleanview II and drive belt keeps slipping off peg that is sticking out from motor pulley causing vacuum to stop working properly and brush to stop moving properly


... Vacuums

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

THE ROLLER BRUSH WILL NOT TURN. I PUT ON A NEW BELT AND IT BROKE IMMEDIATELY. THE ROD THAT HOLDS THE BELT IS MOVING BUT THE BRUSH IS NOT MOVING.


Apparently something is binding the brush, keeping it from turning. Remove any string, hair, etc., that is wrapped around the brush. Removing the brush is the easiest way to do this, then cut the material through at one point.\015\012While th ... Bissell Vacuum - Momentum Cyclonic 1 ea Bagless Upright Vacuum

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a


The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Bearing on end of brush froze causing belt to break. I need to replace the brush and belt. Are there other belts in/on this model?


Hi there. there is a belt in the unit. the owners manual here will give a good guide on how to replace the unit.the ... Eureka 3041BZ Upright Vacuum

Hi I have a dirt devil vision. Hose works, but does not vacuuming the floor. Belts are not broken. Larger belt is moving, smaller belt that moves the brushes does not.


Hi krueger, sorry for the problems but hers an idea how about turning on the vacuum and put your hand under the part where it sucks uo the dirt off the floor and i guessing you would have a little suction, since the brushes are not moving its going t ... Dirt Devil M086700 Vision Bagless Upright Vacuum

I replaced the belt on my bissell model number 3576-2, but when i put it back together, the brushes wont move...the belt tries to move, but the rubber just burns..


Something is binding ... i dont know what ... you will have to remove all parts and reinstall again. Make sure the bearings spin on the brush when it is out ... remove all hair and string.\015\012\015\012good luck ... im sure it is some ... Bissell 6595 Lift Off Bagless Upright Vacuum

We have the Bissell Lift off Revolution vacuum. The brush roll and belt are broken. The brush roll has seized up and no longer spins which caused the belt to burn out. How much is a replacement part cost? Debie [email protected]


You can get the belts for that model here: http://vacbelts.xps.convina.com/bissell-style-8-belt.htmThey are only 4.99 for a 2 pack. Plus they ... Vacuums

Roller brush does not rotate if there is a belt I can't open that part of the vacuum to look. Vacuum is new but I vacuumed a string that caused the brush to stall for a moment. I could smell like when a belt gets hot or burns it's a surfacemax 300.


You need to replace the belt. Replacement Vacuum Belts ... Vacuums

Hi,My agitator brush won't run on my hoover S3590, I changed the belt, that didn't work. I don't see a possible cause in my book except replacing the belt. I think there could be a short, the brush will come on sometimes when pulling back and slightly lifting. Any ideas would be great and can I fix it myself? Thank you for any help, Bobbie


Hi Bobbie\015\012Take apart the electro floor head if you can and inspect inside - it may well be that there's clogged dust preventing the brush from turning and also check both sides of the actual beater bar as thread and tangled hair can often lead ... Hoover S3590 Bagged Canister Vacuum

My Dyson DC 14 is making the horrible "ratcheting"sound only when the brush is engaged on the carpet setting. I have cleaned the brush, so there are no obstructions, the canister is empty and properly on the unit. I checked to make sure all of the "traps" and hoses are clear of obstructions, the belt is on the brush securely and moves freely, the brush itself spins freely, but there is still the "ratcheting" noise. Any other suggestions?


Our DC33 was making the same ratcheting sound immediately upon placing the cleaner/brush head on the carpet. We carefully pulled the beater/brush bar out of the vacuum. Once removed, we pulled the black plastic end off of the center rod. We discovere ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The brush roller stops turning and I can smell the belt burning, then it will catch and start working normal. I looked under the plate to check the belts and they looked okay and no hang ups of string or anything. The only thing that seemed weird was that the smaller belt that actually attaches and turns the roller is a bit loose. The larger belt is tight but looks like its the one that is burning and causing the smell.


Better to replace both belts the smaller one is stretched out thats whyits slipping ,be sure to clean the old rubber off the motor shaft before replacing the belts.it will cause the new belts to run unevevly and go bad before their time ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The belt burnt out and it seems as though the red arrown does not release the belt. Like it is backwards from the green arrow. It had a burning smell and the belt broke. Then the second belt started to burn out when the brush roller wasn't spinning. Not sure what might be wrong. Green light will not come on either.


It sounds as if there may be a piece of the broken belt in there. Look carefully with a flash light and remove any remnants you find, using a pair of pliers if you have to.\015\012\015\012Also, remove the entire brush roller assembly and ... Kirby Ultimate G Bagged Upright Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the


Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Bissell lift off, brush won't move smell burning rubber belt fine


OK - so your brush roller is jammed. And yes, the belt is melting! Unplug the machine, remove the belt (you will need another new one anyway) then see if you can turn the roller by hand. If it turns freely without you doing anything else, then you ma ... Bissell 6595 Lift Off Bagless Upright Vacuum

Rotating brush Hello, my kenmore rotating brush is not spinning at all, and its causing the motor to cut the belt. should i get a new brush? Thank you.


Sounds like the brush roll has an end that is melted or frozen up so it won't move, in which case you need to replace it. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0875 seconds