Having problems with your Vacuums ?

How do I wire vacume tubes and resestors together and what other parts are necessary?

Answers :

Hi. It all depends on what you are constructing, and the type of vacuum tube you have.Most tubes are used as amplifiers so if you were making an audio amp an input device like a microphone will be needed, a power source to drive the tube (sometimes a very high voltage! ) and an output device like a loudspeaker.
\015\012I'd suggest checking out some basic electronics tuition websites to find out what else you might need, and maybe experiment with small transistor circuits first - they are a lot safer.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I wire vacume tubes and resestors together and what other parts are necessary?

Hi. It all depends on what you are constructing, and the type of vacuum tube you have.Most tubes are used as amplifiers so if you were making an audio amp an input device like a microphone will be needed, a power source to drive the tube (sometimes a ... Vacuums

Im trying to put the peice back together that goes under the tube that hold the water the part that goes into the hole in the vacum.. i took it apart because its not spraing right to see if it was cloged.. and now im not sure how it goes back together.. can you please help me.....

I tried to find a service manual for this, but came up with only a exploded view diagram:\015\012\015\012http://ineedbags.com/images/b8920.jpg\015\0 ... Bissell 8920 ProHeat 2XTM Upright Vacuum

How to Install part #KC64EDTEZV06 in the Kenmore canister vacuum cleaner model # 116.22512504 I need a diagram please put pu all the correct wires and parts back together

... Vacuums

CARPET/fLOOR tOOL Electrolux Hoover Model EV4602. Need to buy the plastic connector from stainless steel tube to the Carpet/Floor tool. If necessary buy a new floor tool We live in Cape Town do you know a stockist for spare parts for Elecrolux Hoovers near to us

... Vacuums

While putting on a new belt for my Turbo 4000 Hoover upright vacum cleaner, the parts for the height adjustment (slide bar)fell apart. I'm hoping that you might have a diagram or detail instructions on how to put together again. Thank you

... Vacuums

I have a motor for the Bissell 3750 power head with a black and brown wire, which wire is connected to what?? The old motor just had 2 black wires. There is a blue wire coming from the vacuum and blue wire coming from the light that are together, and a blue wire coming from the light and a black wire that are together. What does the blue and brown wire coming from the motor connect too? Thanks

... Bissell 3750 Lift Off Bagless Upright Vacuum

The extension has lost suction. If I remove the handle tube part, the suction is great to the bendy part, but as soon as I replace the handle part there is none at all and there is no blockage in the handle tube part.

... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum

Trying to wire aa Nutone model 763RL bath exhaust fan/light. The conduit coming from the breaker box has a red wire, a black wire, a white wire and a ground. The fan has two white wires, one black wire, one blue wire and one green wire. I have wired the whites together, but do not know how to wire the blance.

... Vacuums

S 380- power 1800 is my Miele vacuum cleaner which I purchased in May 2009. A big hole has appeared in the tube. Can I cut part of the tube and fix it? if not where can I buy a new one? I looked up spare parts company but they dont tell me if the sise is correct

Miele vacuum hoses can be found athttp://www.totalvac.com/mielehose.html ... Vacuums

My Triton T80 SI shower is leaking from where the outlet pipe assy joins to the heater can assembly. when I checked where the two join together I see that there is a rubber O ring fitting into a recess in the heater can assy. The screws which hold the two parts together does not force a compression between the two parts causing it to leak. Is there another modified unit or am I stuck with what Ive got and should I replace the O ring or the shower.

... Vacuums

We have inherited a Filter Queen Majestic Triple Crown Model 99C vaccum and have no owners manual stating the year it was purchased and parts available. Our power hose electic wire connection (about 6 inches long) which plugs into the main unit is split in the hose attachment end. The motor sound went instantly quieter and I wondered if this was why when I found this frayed electical wire. It has not been used since this problem was found. How much is this single replacement part? I live

... Vacuums

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi

Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

On my Eureka Model 1759A (from mid-1980s), the plastic catch that holds the two parts of the metal body together has broken. I would like to replace the part of the catch that attaches to the top (the part with the lip on it), but I can't find the part online ... or even a drawing. Where can I get this part ? ? ? HELP ! ! !

This latch is riveted to the body. If you are lucky you may find an old Eureka warranty/ repair center with one on the shelf, or another canister for parts. That will be your best hope. ... Vacuums

Reinstalling a hampton bay ceiling fan model-HL52QV P 3LC14 and I do not recall how to wire it to the house electric. A black wire and a blue wire are tied together and a white wire are present fromthe fan. Whichone is connected tothe hot wire in my fan electric box inthe ceiling.

The black and blue wire should conncect to the black wire in the electric box and the white wire should connect to the white wire in the box. This assumes the wiring was correctly installed.Jim ... Vacuums

Took it a part to clean and for got where the wirers go its a bagless upright called the boss theres WHITE WIRE PURPLE WIRE aBLACK AND YELLOW WIRE AND SIGAL YELLOW WIRE MODEL KCL12-13BMLF 120vAC60HZ please tell me how they go back on

... Eureka 5849A Boss Bagless Upright Cyclonic Vacuum

Dyson DC04 i have a loose wire where the cable enters the cleaner how do i open the part where the on/off button is. A wire is loose probably but I cannot get to the interior to check its status. How can I take it apart? the plug is sealed but could it be a loose wire in there?

You have to remove the yellow switch but to do this there is a small hole at the side of the switch nearest to the machine you have to push something in this which will push the clip that is holding the switch if you can do this there is a screw behi ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

The handle was getting hot and we opened the handle and the wires were melted around the switch. I need a part number for it. All I have seen are 2 wire and this is a 3 wire. Thank you.

Had exactly the same problem with my upright Eureka Model 5893\015\012bagless. Eventually, the handle would get hot, and finally it just\015\012quit. When handle was disassembled, the wires were melted and it was\015\012toast. Ordered a switch aft ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Rplacement part I need the part # or a schematic so I can determine the part # for the little black cylinder with 4 wires sticking out of it that commects the power cord to the two motors.

Http://www.oreck.com/customer-service/owners-guides.cfm#Her is the oreck manuals web page.They can also tell you where to get parts. ... Oreck XLS700A Upright Vacuum

I have a Flotec shallow well FP4122-08. A burglar stood on the pump this summer to gain access to my goats building (window). There's a small black tube that came off at both ends. When I put the tube back on, it shoots right back off as soon as the pump is plugged in. I don't know the name of the part (tube) to order a new one, and I don't know if it just plugs onto the fittings of both ends, or goes into the pump at the end with the round fitting on it.

... Vacuums

Hi I have the Ambassador 337 model. I had to rewire the on off wiring due to the "N" wire rubbing through & breaking. I have it all together again although a piece of wire in the shape of a "V", with a bend each side of it has dropped out & I don't know where it came from!!!! Please send me diagram of this model so that I know where it goes. Cheers Ian.

... Electrolux Vacuums

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!

Great. ... Kenmore Vacuums

I am putting my bissel 8910 back together and behind the motor there is a black 3-way tubing connector. One side goes to the pump discharge, one side goes to a tubing going to the right rear wheel (facing the unit from the front) I don't know where the third side goes to. I do not seem to have another tubing for this one to go to? Maybe it is lost or ?

Hi, its hard to know what its for without seeing it. The best way to test this is to start the machine and vacuum a part of the carpet/ floor. Then let me know wht the vacuum is not doing. This will narrow it down. Please, get back to me. This sounds ... Bissell 8910 ProHeat Clear View Upright Vacuum

When i conect the vacum part to maun system it

There is a motor in the power head that could be out or the receptacle, electric cord on power unit or loose wire in power head. ... Rainbow E series Canister Wet/Dry Vacuum


... Electrolux UltraLux 2000 Bagged Canister Vacuum

I am trying to find out a part number for a rubber gasket that goes on the inside of a Hoover Windtunnel Cyclonic Platinum BAgless upright. It is a very thin, light-weight gasket made of rubber that helps seal the filtering tubes. If you know where I can find a parts break down, please advise,,, JON [email protected]

Hi There,\015\012\015\012I'm not sure exactly which part you are asking about, so I went ahead and uploaded the parts schematic of your vacuum cleaner, that will diagram all the parts, and part numbers.\015\012\015\012If you n ... Hoover UH70015 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0415 seconds