Having problems with your Vacuums ?

My kirby g series doesnt **** properly anymore. A friend borrowed it, returned it with a scratch and now its nto sucking like it use to. My son took the head nozzle off, could it be not put back on properly?


Answers :

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=722170
\015\012Generic problem for all Vacuums
\015\012My Kirby G series doesn’t
\015\012Posted by mustang78 on Jun 30, 2008
\015\012My Kirby G series doesn’t **** properly anymore. A friend borrowed it, returned it with a scratch and now it’s not sucking like it use to. My son took the head nozzle off; could it be not put back on properly?
\015\012
\015\012Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. There are a couple of things that you can check to see if it works properly. 1st replace the belt with a new Kirby Genuine belt, the average belt change is every 4 to 6 months, make sure the brushroll spins freely and when you install the brushroll make sure the screw heads are facing the carpet on both sides. B4 you start make sure the bell housing is locked down tight and when you plug it in raise the height adjustment to the highest level then drop it down one step @ a time until you hear the tone change or the brushroll should hit the carpet and @ that point vacuum to see if that is the correct adjustment if not drop it down one more setting. Also replace the paper bag with a fresh one and check to see if the outer bag is dirty and might need cleaning on the inside of the bag and not the outside. If you have further problems please feel free to contact your local vacuum cleaner dealer in your area or call the Kirby cust serv dept listed below. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

\015\012http://kirby.com/ Customer Service – United States & Canada 1-800-494-8586
\015\012Hours 8:00 am to 5:00 pm (EST) U.S. & Canada Fax # 1 (216) 529-6146
\015\012Mail To:
\015\012Consumer Relations
\015\012The Kirby Company
\015\0121920 West 114 Street
\015\012Cleveland, OH 44102
\015\012Thanks, Don the Vac Man
Go Ahead. Use Us.

\015\012
\015\012
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My kirby g series doesnt **** properly anymore. A friend borrowed it, returned it with a scratch and now its nto sucking like it use to. My son took the head nozzle off, could it be not put back on properly?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=722170\015\012Generic problem for all Vacuums\015\012My Kirby G series doesn’t\015\012Posted by m ... Vacuums

Hello I can not find my manual for my vax vs19 swift vacuum cleaner and I am having problems with the cleaner not picking up. It is a 1600w machine and is fitted with a hepa filter, my son took it apart and without the manual it is difficult to reassemble not sure if he has put it back together properly.


Check out this site;\015\012\015\012http://www.vax.co.uk/support/vacuum-cleaner-user-guides\015\012\015\012Scroll down to the one that's applicable. ... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

I have a kirby sentria. vacuumed up my son's headphones and immediately shut if off. took brush off, unwound headphones, put it back together. when i turned it back on, the belt snapped. so i went to vacuum place, got new belt, but when i put it on, with the green arrows lined up, it doesn't have much suction. with the red arrows lined up, it just smells like its burning and i don't want to break another belt! HELP!!


Take the front off the vacuum and check inside both the front portion and the canister for additonal clogs. Sometimes something will get caught in the impellor, causing the motor to overheat. Since there's little suction and the smell, I'd guess th ... Kirby Generation 3 Bagged Upright Vacuum

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi


Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!


Great. ... Kenmore Vacuums

My cigarette injector nozzle on my Top-O-Matic keeps coming off. Why and how do I fix it? With glue? I put the tobacco in, and my empty cigarette tube on the nozzle, then use the hand crank to push the tobacco into the tube and the NOZZLE is coming off with the tube and the tobacco isn't filling the tubes. please email me back a response [email protected]


... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum

Took handle off to use hose now can't put it back together


... Dyson DC25 All Floors Bagless Upright Vacuum

I have a Euro Pro Compact Performer model # EP 171 which I love. It is the best iron I have found for my quilting class. When I went to use it, I found my cats had chewed the cord to the point that it is unsafe. I took it to a repair shop to have a new cord put on it and they told me it had to go back to the factory. I do not want to purchase another iron because it is my understanding this model is no longer made and because I love it. May I send this iron back to the factory to have a new


Hi, you may already have found a solution, but I recently saw this same model iron on ebay! ... Euro-Pro Vacuums

It's been awhile since I have used my shampoo system on my Ultimate G series Kirby. Well, as instructed I took it apart and cleaned it. Now I can?t figure out where to put the ?screen cap? and ?sponge filter?. I have my manual in front of me and the only place it shows the filter and sponge (page 35 in the manual) is when it?s been taken apart to clean. It doesn?t show where to put it back. I don?t know what I would do without all the pictures in the Kirby manual. HELP! Thanx. Visual Kirby Vacuu


Hello,\015\012The littlew round screen goes in the hole where the hose attaches to the tank. The round foam filter goes up in the hole underneath the on/off valve for the foam. Here is a guide if you need any more help...\015\012\01 ... Kirby G6 Bagged Upright Vacuum

I have a hoover celebrity QS wuith the power head. I have only used the powerhead for years purchased in 75) I removed the powerhead to use the brush and the power does not come on but if I put the powerhead back on it works again.


You have done very well keeping this appliance working since 1975!!!\015\012Lucky you!\015\012I'm not certain you would be able to get replacement parts for this model any longer,\015\012Maybe you will just have to continue with the ... Hoover Vacuums

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Bissell Pro Heat 7901 will spay through hose but not the floor and red flow indicator will not spin. So we took the housing off and after unclogging a hose running to the hearter, my husband unhooked the hose that goes to the flow indicator, blew in it and it started spinning. Put the deep cleaner back together, tried to use it and nothing. What else can we try? Can't afford to put it in the shop right now. Thanks in advance.


I borrowed my friends bissell to clean my carpet. It's the 7901. He brought it over and told me that it only sprayed out of the attachment hose. He said he couldn't figure out what was wrong. I'm no vacuum technician but, I am a mechnic. I decided to ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Fantom vpw46h,house pressure washer.the motor runs,it was setting for sometime started,using it,but never had any pressure besides the house hose pressure, with the motor running,then the pressure startes to work great,while using it the wand hose came out of the pressure washer,i put it back in,now the motor will only run when i try to adjust the wand head but will not produce any pressure and will shut the motor off,it seem like as soon as the wand hose came out of the presure washer and after


... Vacuums

I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do they re


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=675093\015\012Generic problem for all Vacuums\015\012I have a Hoover self-propelled\015\012Posted by kl ... Vacuums

Belts I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do t


It is the flat belt that gets stretched and should be replaced at least every 6 months. The V belt wears down so it won't it right in the brush roll V. Maybe the belt tensioner wheel has a problem, sometimes they get hook up and won't engage the V ... Vacuums

I have a kirby G7D model ultimate g, the diamond edition. i took the brush part off , and used the attachments, i put the brush back on, and now it wont turn on.


Did you happen to hit the N/D switch by accident on the bottom. The switch has to be in D to run. ... Kirby G6 Bagged Upright Vacuum

I have a Kirby Sentria and I just tried to use the shampooer. It is not spreading the foam, instead it comes out as a 1 1/2 in strip. The belt is on right, I took it off and put it back on. I don't know what to do. Thanks


Q. What should I do if the Kirby system is not cleaning effectively?A. Check if the green light on the nozzle is on.Check the brush roll to make sure it is not clogged and can move freely.Check to ma ... Kirby G6 Bagged Upright Vacuum

We took it apart to replace the belt and put it back together and now the roller is not engaging my carpet like it use to. the roller is spinning. model # 8955


... Riccar 8955 Upright Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Son took the front plate off the kirby heritage II vacuum thinking that was how to replace the belt, now don't know how to put the three rings and belt catcher back on?


Looked at a kirby vacuum that a family member has and saw how it was assembled! Thank You ... Kirby Heritage II Vacuum

HOOVER F5906-900 I am having trouble figuring out where the inner hoses go, A friend barroed it and took them off to clean them and did not put them back properly. Would you please send me Scamatics to see where exactly these go so I can shampoo my carpets before I go crazy. Thank You Misty Winslow [email protected]


Here is a break down, you may be to trace the lines:\015\012\015\012 ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

I took the trap(or whatever it's called)off the bottom right corner to check for an obstruction as my hose was collapsing when using the attachments. Put it back on(perhaps wrong)and now when the vacuum is turned on, dust blows out the front and there is NO suction! HELP!


Now you have a dyson leaf blower! not funny huh? Ok, just slow down and recheck your connections. Sounds like the motor is running backwards or you are hook up to the discharge. ck for baffles that block off the vacuum to the roller part when at ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Lost manual last time i used the upholstery tool and i think i forgot to put a part back on...from the floor head to the recovery tank the water comes up but i have a gap there...the water won't suck up off the floor...


Send your email address to [email protected] I found the pdf manual file for this unitl ... Hoover F5906-900 Upright Steam Vacuum

Last time I used by Hoover it worked fine, took brushes out to clean them and now when I try to put them back in they won't snap into place and lock. Looks like all tabs on both sides of the brush piece are there and I spin the brushes for the center spindle to line up but it won't snap into place.


Just slightly turn the brush wheel, The tabs look square, but are just a little different in one direction ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Hello. I took the sole plate of to clean the brushes on my dyson dc14 however the brush part came out and i put it back in but since then whenever i switch it over to carpet setting it makes this really horrible clicking grinding sound its only new have only used it a couple of times.


You really need to take the sole plate back off and make sure the belt is running exactly where it's supposed to go and not looped over a piece of plastic or anything. More important is that you make sure the ends of the brush are seated properly an ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0813 seconds