Having problems with your Vacuums ?


Answers :

\015\012Generic problem for all Vacuums
\015\012I USED MY HOOVER 3
\015\012Posted by ROEHL1 on Jun 30, 2008
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. The best thing if the brushes are not rotating is to change the belt on the vacuum because the factory belt sometimes can be stretched out and or the belt could have broke and needs replacement. If the vacuum is less than one year have them check the brushroll / belt to see id the brushroll make be defective and might be possibly be covered under a Hoover factory warranty. The belt change should be done every 4 to 6 months for the best cleaning and to use the genuine belts for the best cleaning. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

\015\012http://www.hoover.com Telephone
Contact our Customer Service Department at 1.330.499.9499
Monday through Friday
8 a.m. - 7 p.m. EST

\015\012Thanks, Don the Vac Man
Go Ahead. Use Us.

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a dyson hoover. up to last week it worked fine. now it will not hoover up bits!!! i have to keep taking the long attahcment off and using that instead which is not ideal!! hubby has checked underneath..all brushes seem to be rotating fine and its not the belt. any suggestions?

Check the inspection air tubes on the Dyson - you don't say what model this is - and each model does have air inspection tubes but can be different to each model - which can usually clog up with dirt/debris thus making the machine difficult to pick u ... Hoover Vacuums

HOOVER STEAMVAC Model# F5842-9RM 120v 12 amp Carpet Cleanerworks well. Hooked up upholstrey attachment, used it. Reassembled to standard operation, the aggitator brushes do not work. I dis assembled brush insert verything good. ran cleaner and the square hole that the bushes insert into did not rotate with cleaner on. turned off lightly tried to turn mechinism in machine no luck. Reassembled aganin, reinserted cleaning tool, then disconnected it. agitator still doesn't work. toggled switch

... Hoover Vacuums

My brushes on my hoover streamvac will not rotate. I removed and cleaned assuring that the filter was also cleaned. The only different thing I have done is to insert the upholstery attachment and removed it after use (didn't work so well) suction seemed weak. I am also noticing that there is air being blown out of sides where the dirty water container is. (don't recall that in the past).

... Hoover F5900-900 Upright Steam Vacuum


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=724631\015\012Generic problem for all Vacuums\015\012I USED MY HOOVER 3\015\012Posted by ROEHL1 on Jun ... Vacuums

I have a hoover all terrain cleaning for carpets and hard floors and the Brushes will not rotate. I have replaced the filter on the bottom which is recommended by hoover and the brushes still wont rotate. Please advise

I assume this unit has no mechanism to turn the brush but instead using the air flow to activate the brush, in this instance it could be that there is dirt which is caught up in the brush which is stopping the rotation.A nice good clean and make sure ... Hoover Vacuums

Hoover steam vac, brushes won't rotate, have cleaned filter by brushes, removed brushes and they rotate okay when off steam vac, tried to ajust level for carpet cleaning and brushes still don't move

There are three things to check when experiencing 'no spin' on the cleaning brushes. 1) Check the small pull out filter screen under the machine. It must stay clean for air to pass to the turbine which powers the brushes. 2) Check that the long shaft ... Vacuums

My pet hair eraser rotating brush does not rotate. I read the manual and cleaned the brush and placed it back correctly, but it is not working when I am using it. If I lift the vacuum from the flour, it starts rotating so I think it is the matter of the amount of contact to the flour. what should I do?

... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

I recently purchased a Hoover SteamVac to replace an old one because the brushes would not turn. I used it last week and then tried to use it last night and the same thing happened w/ the brand new model - the brushes won't. I've cleaned the brushed, the filter and everything else I can see. Can you help?

Those things are a waste of money you better off renting one. but the only thing i could think of is that something is stuck or your belt came off track ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a

Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How to disassemble the hoover steam vac2. the hole that the brushes snap into does not rotate so the brushes are not rotating

The hole the brush shaft goes into is the turbine that turns it. If it will not turn it is seized and should be replaced. ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Roomba. Diagnostic The brushes will not rotate. I have cleaned them, used an air compressor, and checked the front wheel. What can I do to get the brushes rotating?

Go to homesupport.irobot.com and get contact for help.and get the parts too.God bless you ... iRobot Roomba 560 Robotic Vacuum

I have a Hoover Steam Vacuum, All Terrain, and the bristle brushes are not rotating. They appear to be seated properly and, the entire vacuum is clean and free of lint, hair etc., so everything is working properly except the brushes do not rotate. Any help would be greatly appreciated. Thank you.

I checked the owner's manual and the parts breakdown for your model F5807. Both showed that your model has a stationary brush strip and not rotating brushes. Is F5807 the correct model number? ... Hoover F5807 SteamVac Wet/Dry Vacuum

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Hoover SteamVac F5914-900 SpinScrub... The last time I used the hand tool attachment, it worked fine. Just tried to use it again, and now I only drips of water will come out of the hand sprayer, if that. I have tried prepping it for up to 15 seconds like the manual says... no luck with that. Also it is making a big puddle on the floor, probably because the brushes on the main unit keep spinning when I am trying to use the hand tool which I dont think they are supposed to do? Can a

The brushes can be turned off on most of them via a switch on the hood. There shouldn't be water coming out onto the floor unless you are pulling the trigger at that top. You probably broke this when attempting to use the tools. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.

... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

Last time I used by Hoover it worked fine, took brushes out to clean them and now when I try to put them back in they won't snap into place and lock. Looks like all tabs on both sides of the brush piece are there and I spin the brushes for the center spindle to line up but it won't snap into place.

Just slightly turn the brush wheel, The tabs look square, but are just a little different in one direction ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t

... Hoover Vacuums

Brand new Hoover Max Extract Deep Cleaner brushes won't turn. Read manual. Checked filters - all clear. Set Spin Scrub Mode Selector to a scrub setting. Brushes still won,t turn. However the brushes on the Spin Scrub hand tool rotate.

... Vacuums

How do I change the belt on a Hoover Steamvac Model # F5905-900. The brushes are not rotating strong enough. They rotate while they are off the carpet but once you lower them to the carpet they stop rotating.

... Hoover F5905-900 Vacuum

Rotating brushes don't rotate - Hoover F5872-900 SteamVac Wet/Dry Vacuum

Check belt, may be broken or may have come off the brush bar and replace. ... Hoover F5872-900 SteamVac Wet/Dry Vacuum

Brushes on hoover deluxe steam vac cvarpet cleaner are not rotating. Took out the brush assy and drive spins slowly but with little torque. Cannot seem to open the bottom to see if belt or direct drive..something wrong with drive mechanism for 5 brsuhes

(1) Assure the brush shut off lever on the hood is not set to the off position. \015\012(2) Is there still a square pin standing up from the one drive brush? It should be 1/4 square, and about two inches tall. That pin is the drive from the ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

I have a Hoover Agility Steamvac and the brushes will not rotate. I have cleaned the filters and the the "brushes on" feature has been selected. Any suggestions on what else I might try to get it working?

You have a broken brush bar belt. Just simply replace it with a new one. This is very cheap and easy to fix.Pull the cover off of the bottom of the Vac and the belt will be there. If it's not broken then it is still stretched to the point ... Hoover Vacuums

I have hoover mdl U6459-900 and the brush will not rotate even though the main pulley belt is rotating. i have changed booh belts and this did not solve the problem. the suction on the unit seems ok. thanks??

Sound like you need tear down and find whats jamed in it to stop it from turning like string ore hair ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?

Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Help hi there. i have a hoover savvy u8172-900 vaccum. the hose has great suction, but there is limited suction on the main unit and the brush does not spin when i try to use the product. we have cleared the brush of any debris and have also installed a new bag. a few days ago, we disconnected the hose to make sure there was not any foreign bodies stuck in the unit...nothing seems to help. any advise?

As the hose fits into the base (if i am correct) the power at the base should be fine, make sure the base is clean and free from blockage,\015\012you say the brush doesn't spin, has the belt broken, if so replace it, (very cheap) and only a couple of ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.8409 seconds