Having problems with your Vacuums ?

Oreck motor barely moveing


Answers :

Dear Sir>
Please see if the belt is o.k replace if necessary
2) bloked hose + clogged bag , this is very important
3) Motor need maintenance, lube, change the brush, or winding overheating, and need replace.
God bless you
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Oreck motor barely moveing


Dear Sir>Please see if the belt is o.k replace if necessary2) bloked hose + clogged bag , this is very important3) Motor need maintenance, lube, change the brush, or winding overheating, and need replace.God bless you ... Vacuums

HI, my motorized brush barely turns.It makes a hot rubber smell. I took apart and noticed the spindle the belt turns on discolored from heat. Cleaned it, but still no turning of the brush.The vac is a hoover wind tunnel. As it moved accidentally touched the belt/ spindle and burned my hand a little. Very hot in area. Bright spark from motor noted. Was careful not to touch that part!


That means that the belt is stretched and it is slipping on the motor shaft, that is why it is hot and smells like burning rubber. You need to replace the belt. Here is the correct belt you need: ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

My Oreck beater bar is not turning. The bar is free of hair or strings, the motor is working, just the bar will not move


If the motor is working then check the drive belt. There's a door on the right hand side of the Oreck that comes off with a cross head screw. Check the drive belt isn't broken. If its intact then its a possibility that the beater bar has seized up - ... Oreck XL2600 Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi


Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

Oreck XL2200: It turns on, the motor is running, the belt is on properly, but the roller brush is not moving


Quite often this is caused by either a broken or stretched belt, does not seem to be the problem here, or a frozen beater brush, the brush the belt drives.\015\012Remove the beater brush and clean as best you can. Spray a little WD40 between the bru ... Oreck XL2200 Bagged Upright Vacuum

Oreck airhgq motor not working


Dear Sir:1) See if some objets is inscruted in the belt.2) Blocked hose, cleane3) Clogged bag, clean.4) Motor need lube, or change brush, test it for oveheating winding may be need replace.5) Before to do that replace or retight a ... Vacuums

Replacing the Oreck vacuum cleaner motor with a generic Ametek motor, the wiring terminal are different and I need an electric diagram


... Vacuums

I have an eureka deep steam extractor 2590 series and everything is working fine except for the motor it isn't moving is there a replacement part for the motor?? we think iit is the motor but could be wrong ??


Repairing unit wouldnt be cost effective . parts/labor $75.00 /$100.00 .if parts even available . ... Eureka Atlantis 2590A Wet/Dry Vacuum

Local vacuum repair shop replaced motor in Oreck XL 2600HH and now the lights blow out immediately upon powering up the machine. I believe the wires for the lights were mis-wired to the terminal blades on the motor housing. is there a wiring diagram available to properly connect the wires to the motor housing?


Hello. if this repair just occurred return this vacuum to that repair shop as they owe you a valid repair. I agree that they caused the lights blowing out problem. They must repair this for no charge. If you work on it yourself they will blame yo ... Oreck XL2600 Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the


Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Oreck model BB870-AS - I was vaccuming when the vac shut off. The motor just spooled down and nothing more since. I have opened the case. Have power at the switch, and to the motor, but can't get a voltage reading to the common lead at the motor. Is there a fusible link, or something similar in that lead that might have burned out? Thanks!


... Oreck Vacuums

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan


Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

Dead motor? My 8 year old Miele S251i has worked fine, until I was recently vacuuming and moved the plug from one outlet to another. When I restarted the vacuum, it made rrrrr.....rrrrrr....rrrrr noises and smelled like something was burning. I turned it off, and it's shown no signs of life since. Sound like a motor problem? I've taken the cover off and looked at the cord and seen the motor, nothing looks obviously wrong, but I'm also not mechanical.


... Miele S251 Flamenco II Bagged Canister Vacuum

The Oreck vacuum motor sparks the stop running. Plugged to another outlet, the motor did the same things, run for few seconds with sparks and stopped again.


... Oreck XL2200 Bagged Upright Vacuum

Oreck Orbiter Hi Could you e-mail me a wiring diagram for the Oreck Orbiter please? I need to replace the mains cable & the cable to the motor. Thank you, Helen Eccott.


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=618779&thid=681757\015\012Oreck Orbiter\015\012Posted by eccott on Jun 18, 2008\015\012Hi could you e-mail me a w ... Oreck Orbiter Floor Machines ORB-500, ORB-550, ORB-600 Vacuum

Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st


Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums

I have recently replaced the belt and filters. The belt is in the correct position and the rotating brush moves freely. The motor is very loud. It still vacumns but I'm afraid the motor will burn up.


Does it sound different than it did before you made the repairs to it or does it sound the same. Just so you know some of the upright vacuums on the market today sound like a jet airplane landing in your living room.Ca ... Bissell 6594 PowerForce Bagless Upright Vacuum

Brand new LG LUV200r used 10 minutes now after removing dust tank & reinstalling the vacuum motor does not run only the beater bar??? I have located wo circuit breakers both seam to be set. This suction motor should run when the switch is pressed & the beater bar should operate when the handle is moved down??? Not A happy customer will return unit to Best Buy only 100 mile round trip!!!! RDH


... LG Electronics Kompressor Pet Care Upright Vacuum Cleaner LUV200R

Hoover U8185-900 motor shuts off when you move the cleaner forwards but it runs when the cleaner is moved backwards


... Hoover U8185-900 Upright Vacuum

The motor spins but the belt will not move, therefore the rubber on the belt burns right where it is attached to the motor.


Sounds like your carpet beater roller is jammed up, probably with hair or string, in most cleaners you can remove the roller by taking the cover off below the brush. Remove the roller and clean wrapped uo stuff ... Oreck XL Ultra Bagged Upright Vacuum

Motor dying? recently my herritage has been sounding sick, i tried to use it the other morning and it barely could blow up the bag, there is also a hot smell to it when it is running, the motor doesnt sound as powerful as it use to. Any suggestions?


Replace the carbon brushes in the motor. ... Kirby Heritage II Vacuum

Oreck XL9100 Our vac motor was removed to remove a hairpin in the motor.? The tape fell off the wires. Do you have a wiring diagragm?


See diagrams ... Oreck XL Ultra Bagged Upright Vacuum

Hoover u5781-900, motor shuts off (intermittent)when you shake vac or make jerky movements.If you move vac to up right position the vac starts right up.When you giggle vac, motor starts and stops no mater if you just started up or vac for ran for 45 min. Thanks Lucy C.


Lucy\015\012you have a bad connection somewhere in the unit\015\012this is a fire hazard and you should not use this until its been fixed\015\012could be a pinched wire or broken connections ... Vacuums

I have an older Oreck XL vacuum that sounds like it is running twice as fast as it should. I disassembled the entire vacuum, including disconnecting the motor wires, to clean out the hair, string, and other things. When I put everything back and connected all the wires, everything appears to work, including the light. The only problem is, it sounds extremely loud like the motor is running too fast. The model number is: XL3610HH Ser. No. 3610HHXA039740-6 I do not have as electrical diagram to see


... Oreck XL Ultra Bagged Upright Vacuum

I got a Dyson DC16 handheld cordless. Nothing happens when I press the trigger. When I take the canister off, I try and move the black "fan" thing but it won't budge. Should It move? How do I get the motor out?


Hi you have to take all the switch to bits which allows the cable to be free so you can get the motor out which is still tricky but i dont think this is the problem i think this dyson is a bad design its got printed circuits in that could be the prob ... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0386 seconds