Having problems with your Vacuums ?
The brushes on my Hoover Steam Vac F5919-900 stopped spinning. How can we get the panel off to check belts etc.?
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
The brushes on my Hoover Steam Vac F5919-900 stopped spinning. How can we get the panel off to check belts etc.?
Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag
... Euro-Pro EP621 Bagless Upright Vacuum
Hi, i have a hoover steam vac agilty. the brushes on the bottom front quit spinning. they are not locked up as i can freely turn them by fingers. is there a belt that i need to replace? if so, how do i get at it to replacec it? thank you for any assistance
The brushes on all hoover steam vacs are air opperated it uses the suction of the vacuum motor to spin a turbine and in turn spin the brushes. Most likely that path of air is clogged with hair or carpet fuzz. On the top of the machine there is a litt ... Hoover Vacuums
Beater brushes not turning on the wife's Hoover Steam Vac model F5905-900. Found one prior ''solution'' stating that it sounded like the belt was bad. That was my original thought, but on checking schematics and trying to find part numbers at Sears Parts Direct and at Hoover, it does not appear the F5905-900 steam vac HAS any belts to begin with. What's next??
This one I can tell you about from personal experience with that generation Hoover Steam Vac. After using it about 7 or 8 times my brushes stopped turning also.I disassembled it (kind of like disassembling a Chinese puzzle box) and found ... Hoover F5905-900 Vacuum
Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the
... Dirt Devil M088905 Vision Bagless Upright Vacuum
Hoover F6025900 Steam Vac Widepath LS, I own this steam vac and I found bits of rubber under the machine when I turned it on, smelled like burned rubber from a belt? Can you please tell me if there is a belt on this carpet cleaner and if so, how to access the belt? I have taken out some screws and still cant get to the belt? Thanks
Well there is no belt, and not sure what the rubber would be from, everything is plastic or metal. Unless it is really an electrical smell, which means the motor is going bad.\015\012\015\012 ... Hoover Vacuums
I have a Hoover spin vac # 7410-900 the brushes don't spin but i can hear the pump running , checked the brush block stem thats fine the unit feeds water and soap. but i have no vacuu.me or brush movement getting ready to rip the turbine out to check it . the weird thing is it worked fine and then just stopped
... Hoover Steam Vac Dual V w/ SpinScrub Vacuum
I have a hoover f5914-900 steam vac.. and I was wondering if there's a way to take apart the spin brushes to get them cleaned out well. I loaned it to family, and the brushes came back extremely soiled and not spinning.
The brush block may be removed from the base for rinsing.\015\012Yes, you can CAREFULLY disassemble the brush block assembly by releasing each of three latches that hold each of the clear gear covers to the main block. A small screwdriver is u ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Problem with small belt and beater bar spinning. Where to get replacement belt and what is it called model number. Thanks. Only 2 months old 5780-900 Hoover windtunnel cyclonic
Here you can get a package of the belts you need. Also here is a link to the manual:U5780-900 Belts\015\012\015\012\01 ... Vacuums
I checked the belt and it has not broken, but when I start to vaccum the spinning head stops, and I start to smell a rubber smell...Do you think I need to replace the belt, I did get some string caught in it the last time I vaccummed, and it did stink like rubber then also...
Yes you do need to replace the belt they stretch out. Think of a belt like a big rubber band if you were to stretch it out and hold a lighter to it the rubber band would stay stretched out. That is the same thing that happen ... Bissell Vacuums
I HAVE LOST MY INSTRUCTION BOOK FOR THE STEAM VAC SPIN AND SCRUB. I WANT TO USE THE STAIR ATTACHMENT, BUT I CAN'T FIGURE OUT HOW TO HOOK IT UP, OR OPERATE IT. I SEE WHERE THE PLUG IN PART GOES IN THE FRONT OF THE MACHINE, BUT I CAN'T GET THE OTHER PART TO SLIDE INTO PLACE ON THE FRONT OF THE RESOVIOR TANK AFTER I REMOVE THE FRONT PANEL, AS THE DIRECTIONS ON THE FRONT OF THE RECOVERY TANK SAY TO DO. THE FIT IS JUST TOO TIGHT. WHAT AM I DON'T WRONG- OR HOW COULD I GET A REPLACEMENT INSTRUCTION BOO
You can download a PDF version of the manual at the link below. I believe you can contact Hoover as well and they might mail you one.http://www.hoover.com/CustomerService/Manuals/Default.aspxGood Luck! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi
Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums
Have a Hoover model S3670 and the beater brush no longer spins. Have checked the beater belt and it is good, did find out that the light bulb in the unit was bad. Any suggestions on how to test the motor that drives the belt or determine the reason the beater brush is not working?
I usually test the motor with a cord with alligator clips on the wires, and attach them to the black and white wires on the motor ( remove the belt first ). A very common problem with this model was a short circuit developing in the short cord that r ... Hoover Vacuums
Upholstery conversion I can't find where to attach the end of the upholstery hose so that I get suction. I have a Hoover F5888 Steam Vac Spin Scrub.
Take out the duct in front of the tank (#3), the hose end will have a duct on it that you insert in its place. This provides the suction for the hose. Don't forget to put that duct you took out back in place, or you won't have suction when you use ... Hoover F5888-900 SteamVac Upright Wet/Dry Vacuum
No suction My Hoover Steam Cleaner does not have any suction. We have cleaned, checked belts and filter. Still does not work.
I laid my cleaner down and checked it all out and actually vacumed the insides out (we have a lot of animals at our house) and then put the Recovery tank bank on and it worked fine. ... Hoover F7431-900 SteamVac Vacuum
How do you get to the belt on a Hoover steam vac?
I hate to tell you, but there is no belt at all on the steam vac line. they have a suction driven turbine to turn the brushes, and a suction driven pump for the water flow. But definately no belts. \012\012If something is not working on i ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
Brand new hoover steam vac max extract. brushes won't spin. I have check connections, read the manual and nothing. have the switch to power scrub. works with hand tool.
... Hoover Vacuums
My Hoover Wind tunnel has even a cheaper on/off switch and now, you can't buy a new one. I used to go to their website which had a wonderful diagram of the 'guts' but now the only parts are the obvious ones, belts, filters etc....I have to vacuum twice a day and I should be the test person cause its on and off on and off, but now for a vacuum I purchased 3 years ago for over 200 bucks and I can't fix it myself really makes me made or do you know where I can get this part? help? if not, I will ne
Have you tried going to appliancezone.com? I go there when I need parts... ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum
Hoover steam cleaner spin scrub brushes wont turn cant find belt
I just brought mine home...assembled per instructions and tried all the troubleshooting thus far to no avail. So I popped off the brushes per instructions and took a screwdriver to the hole where the brushes axle inserts underneath the vacuum and tur ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Brushes Hoover steam vac f5906-900 .can,t get the brushes to work. Is there a belt that could have broke
This machine has no belts. There is an air driven turbine that propels the brushes. If you look under the little glass window at the left front corner of the machine, there is an intake screen just above the indicator dial. That screen is there to ke ... Hoover F5906-900 Upright Steam Vacuum
Model#F5858-910 hoover steam vac,silver ,spin and scrub. It doesnt seem to spray cleaner it seems to stream it now. what could be wrong? I cant get to end of where it sprays to see if something is blocking it . otherwise it works great. I have it about 8 yrs. always worked good until recently
... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
My hoover power drive vacuum simply died. It just shut off. I checked the plug, etc...I just can't get any power...Can you help?
If no light or motor sound cord is probably bad. Look near AC plug or just replace the plug end. Check with ohmmeter for continuity with switch ON. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum
My hoover model #u6436-900 brush will not spin. I have changed both belts and still nothing. I even checked to make sure they were the right sizes.
Greetings,\015\012\015\012It maybe that the belts were not installed properly, or that the roller brush might be as well. Here's a good video that explains the proper procedure of how to replace the belts on your vacuum cleaner, as well ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
How do you change the belt on a hoover steam vac spin and scrub
You have to turn it over and unscrew some screws you'll see it. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Brushes on hoover deluxe steam vac cvarpet cleaner are not rotating. Took out the brush assy and drive spins slowly but with little torque. Cannot seem to open the bottom to see if belt or direct drive..something wrong with drive mechanism for 5 brsuhes
(1) Assure the brush shut off lever on the hood is not set to the off position. \015\012(2) Is there still a square pin standing up from the one drive brush? It should be 1/4 square, and about two inches tall. That pin is the drive from the ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum