Having problems with your Vacuums ?

I am trying to change the belt on a hoover legacy dirt finder. I cannot figure out how to get to the inside pully where the belt hooks


Answers :

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=733898
\015\012Generic problem for all Vacuums
\015\012I am trying to change
\015\012Posted by fuzzyplus1 on Jul 02, 2008
\015\012I am trying to change the belt on a Hoover legacy dirt finder. I cannot figure out how to get to the inside pulley where the belt hooks.
\015\012
\015\012Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. The Hoover legacy belt change can either be changed from the bottom of the vacuum by either taking out the screws, clips or levers, and then you can remove the bottom plate or the top cover, what ever the case might be. Then you can cut off the old belt and then guide the new belt onto the motor pulley by using a long nose pliers or a screwdriver; if it is hard to reach and then take the brushroll and slide it inside of the belt and then pull back until the brushroll will fit into the brushroll holder, then you can replace the top cover or the bottom plate and reverse the procedure that you did to change the belt. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

\015\012http://www.hoover.com Telephone
Contact our Customer Service Department at 1.330.499.9499
Monday through Friday
8 a.m. - 7 p.m. EST

\015\012Thanks, Don the Vac Man
Go Ahead. Use Us.

\015\012
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I am trying to change the belt on a hoover legacy dirt finder. I cannot figure out how to get to the inside pully where the belt hooks


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=733898\015\012Generic problem for all Vacuums\015\012I am trying to change\015\012Posted by fuzzyplus1 ... Vacuums

I have an old upright hoover vacuum. I need to change the belt but can't figure out how to get to it. The bottom plate over the roller brush comes off but I can't get anything else off to get to the other end of the belt.


Model no. req ... Hoover Vacuums

HOW DO YOU CHANGE THE BELT ON A HOOVER WINDTUNNEL T SERIES REWIND VACUUM..THE BELT BROKE BUT WE CANT FIGURE OUT HOW TO GET IT BACK ON RIGHT.


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Need to change belt on hoover upright model u5093-900, but can't figure out how to open it up to get at the belt.


... Hoover Vacuums

Change belt How do I change the belt. I took the bottom off and removed the roller but can't get the rest apart to get to the place to hook the belt on the the drive.


... Hoover U4270-930 Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

Changing a belt on a Hoover Vacuum Cleaner, Model U4264-930. can not get the old belt off.. U4264-930can not remover old belt on sweeper


... Hoover Vacuums

Vax 2300 vax v-2300 brush is not turning so changed belt snapped as soon as i put hoover on and getting burning smell put another belt on same again and brushes still not moving only 4 months old


If the roller brush cannot be rotated easily by hand, it is likely that debris is jammed inside the end caps.Make note of the direction arrows on the end caps as you remove the roller brush. You will need to know this for reinstallation. The end caps ... Vacuums

How to take apart the Hoover U6437-900 to change the belt and clean it. I have the belts and I have removed several screws. It looks like the knobs for the wheel carpet height and carpet to floor selection are the problems but I can not figure out how to remove the knobs. Besides, I am not certain if this is the problem. Do you have the instructions? Thanks


HERE IS THE MANUAL > http://hoover.com/file/500/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Model UH70120 Hoover Wind Tunnel T Series Rewind Model UH70120 purchased at Target - bagless How can I put on the new Belt? I have taken it apart but cannot figure out how to change the belt. How?


... Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner

Changing belts I cant figure out how to replace belt on my hoover cleaner model u4537-910


Turn vac over, remove the 4 screws holding the bottom plate covering the brush roll. There are 2 belts, one is a V belt ( 38528034) for the brush roll, the other is a flat belt (38528035) that goes from the larger pulley and the motor shat, put it o ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a fantom power pet model #fm722c how do i get inside to change the belt or remove the dirt from inside as well as the vacuum is not sucking the air thank you gail glandon


I have just cleaned out my filter and now it does'nt go back together?????Please help asap. It is a power/pet model ... Vacuums

Where to get manual Hoover em5200 need to change belt?


Http://vacuumvacuum.com/hooverpart.html \015\012this is the hoover webpage for all models\015\012you'll find what you need there ... Vacuums

Hoover elite belt change model number U4245


You have to take the top (hood) off. Mine is red. I'm not sure if they are all the same, but I suspect they are. There are 4 tabs that hold it on. First, gently wedge a screwdriver between the red hood and the black bottom plate around the side of th ... Hoover Elite U5061-900 Bagged Upright Vacuum

How to change belt on hoover SH40060


... Hoover SH40060 Bagless Canister Vacuum

How to change the belt on a hoover dirt finder.


... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

I have a hoover smart 1900 and i am trying to change the belt but can find out to get it to replace broken one.


The casing is secured by 2 screws on the top.near the beater bar take them out to gain access to belt...... ... Hoover Clean Smart Cyclonic Upright Vacuum

Weird noise i have a eureka the boss and i am getting a weird noise figured bag was full needed to change it so i did. Noise persisted so i checked make sure nothing was caught in the brushes. I even checked the belt it was fine replaced with a new one.Still the noise is there help me I am out of what else to check.


Squealing ... Vacuums

I need to change the belt. How do I get it off inside the vac.


Turn the vacuum over so you are looking at the brush.Remove the screws and that plate will come off.The belt fits on the brush,in a groove.The other end of the belt fits on a small wheel about 6 inches back,form the groove on the brush.There may be ... Dirt Devil Vacuums

Do you have a diagram of the inside of the brush roller and motor area? I took a machine apart that was given to me and can't figure out how the little belt hooks up to the brush roller, etc. I must be missing parts or something but can't find a diagram to know.


You can find a help video relating to replacing the belt at:http://www.ereplacementparts.com/eureka-426a-stick ... Eureka 426A Upright Vacuum

I have a dyson Absolute 04 hoover, the brushes underneath do not turn,I can see the belt but am not able to get into to it to change it.could you please assist. thank you.


HELLO, YOU HAVE 4 SCREWS THAT YOU TAKE OFF THE BOTTOM COVER TO REMOVE OR HELP GET TO THE BELT, IF THE BELT IS'NT BROKE TRY SPINNING THE BRUSHES BY HAND TO SEE IF YOUR CAN SPIN IT OR BREK IT LOOSE IF IT IS THE BELT THEN YAA REMOVE THE BOTTOM COVER TO ... Vacuums

I can't figure out how to change the belt on my hoover bagless Sprint upright. Please help.


1 set up vacume with bottom facing you , making it easy to deal with.\015\0122 remove the 4 screws holding base plate on and carefully remove the base plate, on mine there is a small catch that must be released.\015\0123the belt compartme ... Hoover Vacuums

The belt wont turn...i cant get in to the inside to check to see if the belt isnt on the roller...how do i get up in there..i took the bottom plate off and you still cant get inside... thx Peggy


The following site has some great info on your machine:\015\012\015\012www.dysonmedic.com ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How to change belt on old upright Hoover vacuum


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How do I get inside to replace u belt ?


Remove the three philips screws holding the yellow cover on the base. It will lift off, exposing the roller bar and belt. There are further instructions for belt change on a label inside. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1531 seconds