Having problems with your Vacuums ?

Sebo x4 automatic broken wire in handle assembly

\015 I need to split the handle assembly to fix the problem\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Sebo x4 automatic broken wire in handle assembly


... Vacuums

Spare wire? My SEBO X4 flex had to have the fex shortened because the cable sheathing had come out of the internal gripper and there was a couple of inches of two strand wire hanging out the cable entry point before the insulation sheathing started. No problem doing this but on the live switch terminal there was a piggy back spade connector. The second wire from this went down inside the handle and just ended with a bare terminal hanging in space. It hadn't come off anything, there wasn't anyth


Greetings from GoVacuum.com,I took a picture of the Sebo X4 wiring in the handle of the machine for you. This is a brand new machine taken out of the box, this is how the wiring should look. You'll see that there are 5 total wires here. ... Sebo Automatic X1 Bagged Upright Vacuum

Broken handle release spring assembly on an electrolux intensity


... Electrolux EL5020 Vacuum

Take handle apart sebo vacuum - Sebo Automatic X1 Bagged Upright Vacuum


... Sebo Automatic X1 Bagged Upright Vacuum

My Electrolux Regency Series upright vacuum brush motor does not activate. Cleaned the brush and press reset to no avail. Opened handle switch assembly and checked each wire attached to all three switch settings. Tried disassembling brush assembly but could not pry open after removing all screws.


... Electrolux Vacuums

I cannot charge my two year old electrolux pronto. I purchased a brand new hand held vacuum for it, but even the new one does not charge. When I plug in the cord nothing happens. If I turn on either the long handle or the portable unit within the long unit, the blue charging light comes on for a few seconds, then out. This tells me that the circuit is intact without a broken wire somewhere. I took it all apart carefully and could see nothing broken or out of place. On re-constructing it, it


It must be the charging transformer. We have already ruled out the vacuum unit. Unfortunately the transformer is not a serviceable part, and will need to be replaced. ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne

I have many SEBO automatic X4 vacuums with broken foot pedals. I would like to buy 5 foot pedals that I believe the part number is 5059DG can you tell me where to get it


I guess that depends where you live... plenty of spares sources online (google sebo vacuum spares)... otherwise google sebo dealerships in your country/locality. ... Sebo X4 Bagged Upright Vacuum

Mrs Cleaner flex has pulled out how do I replace Electric supply wire to switch on handle has broken at switch. How do you remove switch to repair? tonysimmons


Hi\015\012\015\012\015\012\015\012\015\012\015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have an Electrolux Epci 3500 Sr upright vacuum cleaner ... 100 percent positive switch is shot and one of the wires inside is fried but before buying a new handle assembly online how do I check the motor to make sure it's not fried?


The switch is replaceable, so you don't need to replace the complete handle assembly. I've got a 3500 that I replaced the switch on and it works great now. You can get a new switch at the local Aerus Electrolux store. To find the nearest store, ju ... Electrolux Epic 3500 Vacuum

Poor cable connection in handle - Sebo Automatic X1 Bagged Upright Vacuum


You will have to open handle where switch is . undo screws where power cable goes into switch. Cut +/- 100mm off exsisting cable & rewire . ... Sebo Automatic X1 Bagged Upright Vacuum

Sebo has become erratic in electrical power and today I have sparking from the top of the electrical lead where the wire goes into the handle. Can this be fixed?


Yes it can be fixed. If you are handy or someone in the house is handy you may even be able to do this yourself. All that is required is to remove the one screw out of the handle there near where the cord goes into the machine ... Sebo X4 Bagged Upright Vacuum

Electrolux Discovery II 1500c Upright Handle Switch Assembly


... Electrolux Vacuums

Broken handle release


Most times they don't break, it is the 2 screw holes at the back that back and the top will raise up from the base. If this is the case, remove the 2 screws and install longer ones with a flat washer on them to fashen down the top. But first the to ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Assembly I am trying to assemble the eureka smart boss. The problem that I am having is that the handle is not completely fitting into the cleaner body. I can slide the handle into the handle supports but it doesn't seem to click together. There is a space at the top; it doesn't seem to be able to fit as closely as the bottom. Thanks, Lisa


It may not just slide into place, you may have to knocj it into place, then put the screws in to secure it. ... Vacuums

The handle was getting hot and we opened the handle and the wires were melted around the switch. I need a part number for it. All I have seen are 2 wire and this is a 3 wire. Thank you.


Had exactly the same problem with my upright Eureka Model 5893\015\012bagless. Eventually, the handle would get hot, and finally it just\015\012quit. When handle was disassembled, the wires were melted and it was\015\012toast. Ordered a switch aft ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

I broke the handle part of the shark steamer #53101. I don't have the book to try to tell you the parts I need. Can you send me a picture or a copy of the steamer. It is purple. The above number may not be the correct one. It is broken in the center part. It has a little small circular piece that joins the two pieces which are broken. The beginning of the handle at the bottom of the steamer and the next session which has the steam release. The top of the handle is okay . It the middle and bottom


Hi,Ann there are very few parts for these...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

How to dismantle twin clean powerhead to repair broken wires? the wires to the pc board have broken but can't seem to be able to remove plastic cover over wires without breaking cover.


... Electrolux Twin Clean Bagless Canister Vacuum

Sebo Automatic X1 cleaner, toothed belt replacement


OK, here goes... (there may be more detail here than you need, but it's a copy of a solution I wrote for someone else)  NOTE - any use of the words LEFT and RIGHT assume that you are looking from the REAR of the machine. \015\0 ... Sebo Automatic X1 Bagged Upright Vacuum

Where can I purchase a replacement wire for the handle of my aerus centralux hose? It's the black wire that runs from the switch in the handle and attaches to the pins in the wands.


Any Aerus Electrolux store should have them in stock.\015\012You can find the one nearest you by following the directions on the below site:\015\012\015\012 ... Electrolux Centralux Vacuum

Change Belt on Sebo Automatic X1 - Sebo Automatic X1 Bagged Upright Vacuum


OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the FRONT of the machine. NOTE ALSO - the machine has two toothed belts, it makes sense to change both while you're at ... Sebo Automatic X1 Bagged Upright Vacuum

Broken handle broken top plastic handle


Hi, \012\012Here is a tip that I wrote about how to find the parts you need for your Shark\012\012How to Find Shark Parts and Access ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

The handle for my Eureka 5993 AVZ was getting very hot when used. Finally, the wires around the switch melted and now the vacuum will not work. What is wrong? Is the switch bad? The wires only melted in the immediate vicinity of the three-prong switch. Nothing else appears to be wrong; the vacuum worked fine when it was running - except for the handle getting hot. Thank you!


Try cleaning all...\015\012if have sam paoblem need replaced main motor.... ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

The top front corner of the rake assembly on our Littermaid Mega box is broken off. Where and/or how can we get a replacement assembly to fix this. Because the piece is broken off, the "wheels" on that side do not like to stay in the rail and the rake doesn't work properly.


... Vacuums

Need to replace to handle assembly


... Electrolux EL5020 Vacuum

Sebo automatic x1 - switch


Have a vacuum store look at this ... Sebo Automatic X1 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0465 seconds