Having problems with your Vacuums ?

Kirby G5 grating noise from tech drive

\015 When I use the tech drive there is a loud grating noise when moving the machine backwards\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kirby G5 grating noise from tech drive


... Vacuums

The tech drive on my kirby makes quite a noise whenever it moves the machine - is this normal??


No, you must have a problem with the transmission. ... Vacuums

Kirby G5 - the Tech Drive does seem to have much power


You need either a new nutreal cam bracket assembly, that is what engages and disengages the tech drive.OR to adjust the handle pivot assy- diffucult . this is not for the faint of heart. it is possible to fix them as i used to repair kirbys, howeve ... Kirby G5 Bagged Upright Vacuum

I have a kirby vacuum model G7D when engaging the tech drive, the machine zips forward to fast, the main suction mech rears up and won't stay on the floor. A technician replaced the nutural drive assy. Could he have caused some mechanical malfunction to occur??


My understanding of Kirby vaccums is that they are lifetime warranty. It appears that the drive assembly that was installed was not adjusted properly after it was put in or it is defective. I would see about getting it back to the tech for further wo ... Vacuums

Kirby g3 tech drive


So when u pull it back it's like it's not engaged at all? then it maybe the reverse is out....with the fwd soon to follow. remember the vac is 20yrs old; & working that long? it definately served it's purpose.\015\012depending how much mo ... Kirby Generation 3 Bagged Upright Vacuum

Kirby g7d wont go into tech drive


... Kirby G5 Bagged Upright Vacuum

When I put my Kirby in drive it hesitates and then lunges and make a grinding noise. The handle seems loose.


Drive has been knocked out off position, will need machine service should cost 39.95 should not need any parts though ... Kirby Ultimate G Bagged Upright Vacuum

Why is the tech drive on my kirby sentria is clicking when pushed forward


... Vacuums

Kirby g4 tech drive, when plugged won't come on ,is it the motor or something else ?


Does anyone know if there is a reset button on the Kirby G4? And if there is where it is? ... Kirby G4 Bagged Upright Vacuum

I might buy a used Kirby Heritage II , my question is does it have drive tech


Kirby Heritage is not a self propelled vac...but the newerG series 3-4-5 etc are. This is a rugged fan first vac, expensive to maintain if you are rough on it and bulky to use but it grooms the carpet nicely. It is also a fan first vac, m ... Kirby Heritage II Vacuum

Tech drive slips and squeaks - Kirby Vacuums


Machine needs serviced, 39.95 the engineer will re-set everything ... Kirby Vacuums

Kirby g 5 head bounces when vacuuming and tech drive is engaged, does not do this everytime


First change the belt, even if it is not broken. also make sure that the height adjustment is raised up high enough, the higher the better ( when adjusting a vacuum you want the tips of the brush roller touching the tips of the carpet fibers ) also t ... Vacuums

I have a kirby ultimate g diamond series. The tech drive lever just fell off. How can I fix this?


Ouch...You need new pedal assembly. Just Google 558401S . I saw one for $16.10.You can try to fix it just you would have to install it back at a certain angle. clean shaft very well with alcohol so it is completely grease free and use a d ... Kirby Vacuums

My kirby vaccum has tech drive and it is stuck in reverse. The wheels spin backwards up lock up when I push it forward


... Kirby Ultimate G Bagged Upright Vacuum

How do i convert kirby tech drive g4 to a carpet shampooer


Watch instructional video HERE.\015\012\015\012Good Luck,\015\012Rocky ... Kirby G4 Bagged Upright Vacuum

Purchased ProHeat 7920 Po-Tech recon. Unable to use main brush as no water/cleanfluid. Belt drive is ok. Grateful advise location of fluid jets as not visable behind main brush. Turbo brush works well.


Make sure there is liquid in both the Tank-in-Tank and the SmartMix Bottle and check for spray through the upholstery hose. If the hose does not spray please check the following:\015\012 \015\012- Remove the belt access door and ... Vacuums

The tech drive petal on my Kirby G5 fell off. How do I fix it?


I assume you mean the pedal on the back of the transmission, if so, if has come apart, there is a piece that is pressed onto the shaft. Best to replace the pedal assm., the old one may not stay together anymore, you will have to pull the transmissio ... Vacuums

When kirby sentria is put in drive it goes backwards


... Vacuums

Loud Noise My Kirby vacuum makes a very loud noise when it is turned on. It still works and picks up trash, but the noise is new.


I believe you will find the answer you seek by clicking on this link. \015\012\015\012http: ... Kirby Ultimate G Bagged Upright Vacuum

I have kirby k5 it will not go into the drive .I took it apart and the shaft that put it into drive 'had fell out.Not sure how to get it in the rightway to make it go from nut. to drive Are therea parts page you can email so i can see how it works thanks john [email protected]


... Kirby Vacuums

When selecting the carpet cleaning mode, it appears the belt is slipping (due to the noise) over the drive pulley. How do you access the drive mechanism to replace belt or inspect drive pulley and belt condition?


On those units you must replace the clutch assy. you cant just replace the belt. there is also a special tool used to get the new belts on the brushbar. If you would like me to walk you through this repair let me know. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My kirby sentria won't go into drive - Kirby G5 Bagged Upright Vacuum


... Kirby G5 Bagged Upright Vacuum

Kirby g6 My kirby is running louder than usual. Kind of like its screaming instead of running now. Its working fine, but the noise is really unbearable. What could it be?


Could be the bearings, especially if the machine is old or the dust filters have not been replaced regularly.\015\012Check to see if the noise is still present after the machine winds down when the power is turned off. A rattling sounds means b ... Kirby G6 Bagged Upright Vacuum

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John


It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum

Both drive and slave belts are intact and tight on the Bissell ProHeat 2x. The brushes will not turn. When last turned on, there was a loud snap noise and something is broken in the power head drive train. Can we repair this or is there a service center near the Hastings, MI area? We need this fixed ASAP. Thank you.


Sounds likely you should take it in your drive gears might have a problem ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0325 seconds