Having problems with your Vacuums ?

Belt for vacumn

\015 Im tryin to find out how to put the small skinny belt not the fat wide belt on because I got a new one and put it on how I thought it went but it wont roll the brush once the brush hits the carpet it stops rollin.\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I thought I was buying a manual. I put a new belt on my vacumn but it makes a funny noise and does not leave vacumn lines on the carpet like it used. I don't know if it takes two belts or one.Wish I had a manual.


Hi Frrank: The Owner's Manual for the Euro-Pro Infinity NV31N Vacuum can be downloaded in PDF from the following site:http://dl.owneriq.net/d/df ... Euro-Pro NV31 Infinity Vacuum

I have recently replaced the belt and filters. The belt is in the correct position and the rotating brush moves freely. The motor is very loud. It still vacumns but I'm afraid the motor will burn up.


Does it sound different than it did before you made the repairs to it or does it sound the same. Just so you know some of the upright vacuums on the market today sound like a jet airplane landing in your living room.Ca ... Bissell 6594 PowerForce Bagless Upright Vacuum

431DX how do you change belt eureka vacumn belt


... Vacuums

Houver Cleaner My self propelled windtunell baged Vacumn has a broken belt. The small visible one that is visible is intact. This is the thick belt. I cannot for the life of me figure out what to open and how to replace it. The model # is U6 401-9RM I keep asking for a manual online but it doesn't recognize this number. I am 67 yrs old broke and fix it challenged..lol can you help me?


Take off the bottom plate, The flat belt ges around the motor shaft and then around the bigger pulley by the V belt. It will stretch to o on.\015\012\015\012 ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How do I change the belt on my vacumn


There should be some screws on the bottom of the machine. take out the screws and remove the cover ... Bissell 6594 PowerForce Bagless Upright Vacuum

Belt for vacumn


... Vacuums

I need a manual for this model vacumn so I can tell how to replace the belts.


A manual in downloadable .pdf format is available here:http://www.dirtdevil.com/search.aspx?q=M089900&type=3 ... Dirt Devil M089900 Upright Vacuum

How can i make my roll brush move on my eureka vacumn AS1101 A the belt is not broke so why wouldnt it work


... Vacuums

Change belt on sears upright vacumn 116.34613305


... Kenmore 33721 Upright Vacuum

I need a manual for the Eureka Capture vacumn. I have broken the belt and don't know how to take it apart to replace it.


Here is the belt you need and the manual which has instructions:Eureka Capture Replacement Belt ... Eureka 12 Amp Capture Vacuum Upright Vacuum

How do I put an new belt on this vacumn cleaner?


Surprising though it may seem, that will depend on what make and model of vacuum cleaner you've got. Instructions will be in your user manual (if you no longer have the manual you can usually download a copy from the maker's website). ... Vacuums

Eureka pet expert upright vacumn. Changing the belt. Model #3276BVZ


... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

How to apply the belt on a kirby vacumn - Vacuums


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=759766\015\012Generic problem for all Vacuums\015\012How to apply the belt\015\012Posted by wccles on J ... Vacuums

How to replace the belt on a Eureka whirlwind 5190 vacumn


... Eureka Whirlwind 5190 Vacuum

The vacumn runs but brush dose not turn belt is good. It's a dyson 110 us c 10417


Now is it air driven or belt driven? It could be the belt that's not turning the brush. Check if the belt is loose or is broken. If it's air driven, then check and see how the condition of the bearings are. If it doesn't roll smoothly then you need t ... Vacuums

I just changed the belt an dthe vacumn doesn't have any suction.


Check the dirt canister lid and that the lock lever is in proper position ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

My vacumn wont pick anything up and it wont self propel. I checked the belt - it is fine.


There are numerous things to check. \015\012\015\012Check for hose clog\015\012Brush belt has many hairs and doesn't move\015\012Brush belt broken/loose\015\012 ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

How to change fan belt on dirt devil d150 hand held vacumn


... Vacuums

Where do i buy a new belt for my eureka pet lover bagless upright vacumn


... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

How do you change the belt on a hoover wind tunnel vacumn/ not self propelled?


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Belts on hoover mach model uh70040


... Vacuums

How do you replace the v-belt o a hoover Model U6432-900


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Belt slipping Belt slips off and rubs causing burning smell from the belt over heating. Of course this puts an indent into the belt and has to be replaced. How do I keep the belt from slipping off? I see no place for a belt adjustment. Which I know would eliminate the problem. Really aggravating to have to replace belt only after two uses.


On the roller/brush where the belt sits if that is scarred up or grooved out that will cause the belt to slip if you can fix roller try but i suggest new roller ... Hoover Company Wind Tunnel U53019 Upright Vacuum

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v


I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I Need to change the belt on hooverwhirlwind


There should be 4 screws on the bottomsome have little flat snap that secure the bottom cover on.push the snaps toward the outside of the base and the cover should come off.if they are screws just remove the screws and take off the bottom plate.then ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0343 seconds