Having problems with your Vacuums ?

The peedal drive fell out of my Kirby Model G7. Can you tell me how to put it back together..

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The peedal drive fell out of my Kirby Model G7. Can you tell me how to put it back together..

... Vacuums

The TechDrive Pedal on my Kirby G6 fell out of the back of my vacuum cleaner. I removed the screws from the metal plate one the bottom to try to see if something had come a loose. Can you send me a diagram so I can put it back together or tell me where I can get a service manual. The only part I am having trouble with is the metal piece inside that engages the power drive. Thank you.

The pedal drive fell out . Do you have a manual telling me how to get it together again.. Thanks, Dianne ... Kirby G6 Bagged Upright Vacuum

Hoover model U6476910 I was cleaning out the bearing sections of the brush when a spring type pressure washer fell on the floor. I did not see the washer when I took it apart and I can't tell where it goes in order to put it back together. It is very thin and measures about 5/8 inch with an 11/32 inch hole. Frank Nething

Hi frank this sounds like its a compression washer, you normally find these on the end of the roller to even out any movement from side to side, as you look at the hoover's brush head, it should slip into a groove on one side with the roller...hope t ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi

Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

I have a Dirt Devil M088400 - Vision Turbo Vacuum. A spring fell from the bottom and the carpet height adjust isn't working. The rollers under the unit won't stay in place either. Can you tell me how to put the carpet height adjust back together?

The roller attaches to wheels. There is a spring that attaches from roller to hight adjustment selector which is a plastic peice with a little hook on bottom that spring attaches to. Both peices should have a hook that the spring ttaches to. ... Dirt Devil Vacuums

I own a singer sewing machine model 4562 and tension assembly came unscrewed and now I don't remember how to put the pieces back together. Do yo have a diagram that can be emailed to me so I can put it back together? Thanks

... Vacuums

Had infamous extra part once I put my steam cleaner back together

Steve, The o-ring goes inside the turbine assembly on the metal shaft. ... Hoover F7220900 SteamVac V2 Upright Vacuum

Replaces the belt on dirt devil dynamite pluse model put everything back together started it and it burt the new belt up that fast. I put it around the beater brush and the metal bar I thought it should go around, yet it seemed like there should be something else there to put the belt on. What do you suggest? Do you have picture I could go by?

The metal bar you put it around if the bar itself does not spin it is going to burn the belt up. Every thing that the belt is supposed to go around has to turn or the belt will rub on the piece not moving and brake. ... Vacuums

Hoover wind tunnel U6425 self propell drive pulley and nut fell off.Now when I try to put it back on and tighten it pulls the clutch assembly over so the accuator is in drive all the time and won'

... Hoover Vacuums

Have cleaned and pulled apart the rainbow vacuum Model D4A. Put it back together now there is no suction. Which way do the fans go back on? Do you have any diagrams of layout?

... Vacuums

I have a Series G Kirby Model G7D. The other day when I was vacuuming all of a sudden the TechDrive (Power Drive Assist N/D) pedal fell off. I see the hole that it goes into but when I put it in it's loose and falls out and doesn't control the power drive anymore. When I shook the vacuum I heard something rattling around inside the vacuum head. So I unscrewed the bottom and looked inside and found a small metal part labeled K3 on one side and T on the other side. It looks like it would fit

Hi, I have a Kirby G4 and i'v replaced the carbon brushes myself using a step by step guide however since its been back together it worked for about five minutes it then started sparking from the inside!!(a lot!!) I'v obviously touched something i sh ... Kirby Ultimate G Bagged Upright Vacuum

My Animal Dyson (the purple one) is making strange noises. The ball will not roll. I've taken it apart and put back together and it works for a couple minutes and then it won't work again I think it's Model DC24 or 25. Pretty sure its 24.

... Dyson Ball DC24 Bagless Upright Vacuum

I have a sta rite (pentair) cristal high rate sand filter model T-200-BP-1....its leaking water thru the top of the valve, where the valve cover screws on the valve body assembly. it leaks water out where they go together around the screws. Also when i vacuum it, everything that i vacuum gets washed back in the pool when its on the filter position. Also the backwash leaks when its turned 2 the filter position, does it supposed to do that?...the only way i have gotten it to stop is to put a seper

... Vacuums

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc

... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have a Bissell 1623-1 Steam Cleaner. It will work good for about 2 minutes and then after that it will not dispense cleaning solution on floor or through the hand held wand.I have replaced both drive belts with no improvement. I have cleaned it and found no obstructions in hoses and spray nozzles, put back together and it still will not dispense. Is it possible the pump or solenoid is no working? Aaron

... Bissell 1623 Steam Cleaner

I have a Oster Adjustable cliper model #284-16 Series B. I need to know how to put it back Together.

... Vacuums

Problem with cord rewinding mechanism on my Nilfisk King!Whilst repairing broken cord(successfully)the metal coil thats part of that mechanism sprang out!Can someone out there tell me how to put it back together again PLEASE.I would so like my cord to be able to retract again

... Vacuums

We took it apart to replace the belt and put it back together and now the roller is not engaging my carpet like it use to. the roller is spinning. model # 8955

... Riccar 8955 Upright Vacuum

I recently acquired a Sunbeam SA12587 water cooler/dispenser w/refrigerator Model#YLR2-5-90HZ3. I took it apart to clean it and now i can't figure out how to put it back together PLEASE HELP!!!!! it's been sitting like that for a week!

... Sunbeam Vacuums

My foot pedal to my Bernina 930 broke last night. The plastic around the screws broke off so everything fell out... I have the pieces, but not sure how to put it back together. Can this be repaired.

... Vacuums

I have an f5833-900 hoover steam vac that i cannot put back together. where do i find the manual for this model

This should take care of you:\015\012\015\012http://www.hoover.com/pdfs/manuals/F5835900.pdf ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum


... Electrolux UltraLux 2000 Bagged Canister Vacuum

I took my vacuum cleaner apart to clean it because it was clogged inside and now I am having trouble putting it back together. I am looking for a manual of some kind to show me how to assemble it. It is a Kenmore Progressive Model # 11636933502

... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

I replaced the belt on my bissell model number 3576-2, but when i put it back together, the brushes wont move...the belt tries to move, but the rubber just burns..

Something is binding ... i dont know what ... you will have to remove all parts and reinstall again. Make sure the bearings spin on the brush when it is out ... remove all hair and string.\015\012\015\012good luck ... im sure it is some ... Bissell 6595 Lift Off Bagless Upright Vacuum

I bought the Eureka 4703D model vacuum and my very first time powering it on, it was extremely loud - abnormally loud, and I don't know if it is loud like that because I possibly put it together wrong, or there is something wrong with it or it was previously damaged and I would like to know if this is something I can fix myself or do I have to take it back apart and return it to Walmart where I purchased it from. When it makes the loud noise, it does vacuum fine but the noise is just unbearable

... Eureka Power Plus 4703D Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 1.2161 seconds