Having problems with your Vacuums ?

When I push the start button, unit lights up and as soon as it starts, the gfci pug trips. any suggestions

\015 I thoughly cleaned the unit prior to this occurring. It was running fine prior to the cleaning.\015

Answers :

1)you must test the c. board, can be faulty. by that reason all this phenomenon appear. Any component can be in short, such diodes, capacitor, resistor, triacs, SCR. etc or IC.
2) you must call you supplier for get help ONLINE chat with them.

God bless you
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When I push the start button, unit lights up and as soon as it starts, the gfci pug trips. any suggestions


1)you must test the c. board, can be faulty. by that reason all this phenomenon appear. Any component can be in short, such diodes, capacitor, resistor, triacs, SCR. etc or IC.2) you must call you supplier for get help ONLINE chat with them. ... Vacuums

Electrolux Centralux I have a Electrolux Centralux. When I plug the hose in at one of the wall outlets the motor will not start. If I go to the motor and slap the unit it will start.....then...it will not stop unless I unplug the power cord to the motor. If I plug the power cord back in, the unit will not restart until I slap the motor unit again. The unit has only been used 20 - 30 times. Any suggestions?? Thanks, Bruce


I dont know if you had your unit looked at yet but it sounds like the Power module is going. I repair the machines so I know some of the work. ... Electrolux Centralux Vacuum

I press the start button and sometimes the motor won't continue running. As soon as I release the start button, it turns off. Sometimes, if I remove the cannister and replace it, then it will run correctly. Sometimes not.


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The roomba or I robot will upon pressing the start button go around in circles, than starts to goin one direction, than stops and goes in a circle. The unit is clean and the unit reset. Bill


Is the front bumper **** in? ... Roomba Vacuums

My dyson won't stay on. I push the red power button and it begins to start but as soon as I stop pushing it, it stops. It will only work if I keep pushing down the start button the whole time I'm using it. HELP!!! I love my vacuum!


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The unit does not start when I turn on the switch on the handle. The power nozzel runs, but the vacuum motor does not. The reset button is not popped, there is 110volts to the unit, and I tried flicking the switch inside the unit underneath the filter with no responce.


... Electrolux Centralux Vacuum

UNIT WAS ON BUT NO SUCTION. I STARTED TO CHECK THE BRUSH UNIT AND THEN NO POWER. IS THERE A RESENT BUTTON? i HAVE CHECKED THE BREAKER.


I need to know what make / model of the unit you are using here and I can help you. What make and model vacuum is this?Thanks, let me know by replying here..Tim ... Electrolux Central Vacuum

I have a RIVAL Vacuum Sealer Model VS150. I need to repair the power button that is located under the cover. It looks like someone pushed the button into the machine without lowering the cover. I live in Bridgewater, MA & the address on the unit is in Milford, MA. Any suggestions.


... Vacuums

The breaker on the vacuum trips after about 3 seconds on. The canister was extremely full and started to smell like burnt wood, we fully cleaned out the unit. Now when the vacuum is turned on, the motor sounds weak, and then turns off in a matter of seconds,and we have to reset the breaker on the vacuum to get it to start again for another few seconds.


This sounds indicative of a worn set of carbon brushes on a dieing motor for a central vac. the armature is ,likely damaged causing teh breaker to blow. Please post back with more details as to make and model. Do not atempt to run the vac ... Vacuums

My vacuum won't stay on. Will start when I push on button but will shut off as soon as button is released.


... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a kenmore progressive 359235 vacuum with intelliclean. Has been great for about 3 years but now the brush bar has stopped turning. This is a direct drive unit with a circiut breaker reset button on top . The button is not tripped. Any ideas ?


... Kenmore Vacuums

Our two-year-old miele antares stopped working...you cannot get it started when pushing the start button (yes, the cord is plugged into a live outlet); no external damage to the unit


... Miele S4210 Antares Bagged Canister Vacuum

I have a Miele s251i vacuum that was working just fine until I umplugged it (while running) and re-plugged it in at a closer socket. When I replugged it, it started for a second and then stopped. Will not start now whether we use the on/off switch or not...suggestions? Would also like to know how to disassemble the unit so I could check out the wiring with a multitester..thanks


I just had exactly the same problem. Opened the vac, checked the circuit\012 next to the motor and it can be clearly seen that the Triac burned thru\012 the PCB. Will replace it and check again. Vac bought long ago, works \012extremely well. ... Miele Vacuums

I have a miele S712 (2 yrs old worked fine yesterday) - I had been doing some diy work inside and had the vac on just to reduce some of the dust in the air - after a while the vacuum fizzled out. I guessed it had overheated and took it outside to cool down - when I tried to turn it back on pressing the power button gives it power and it starts to **** but it won't STAY on, soon as you release the power button it stops, and the orange bag indicator is showing full. As I have a compressor I took


You have got dust in the micro switch and it is not latching on, if you look at this and clean it, that will solve your problem, however blowing the motir has probably wrecked the motor bearings. ... Miele Vacuums

Vacuum won't stay on. When I push the button to start it, the motor shuts off as soon as I let go of the button.


You have a broken switch (replace) or hopefully something caught under the switch. Regards Billy ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have an Ecectrolux Epic canister vacuum. As soon as it starts sucking, the vacuum cuts off. I put a new filter and bag in, but it doesn't seem to help. If I open the front where the bag goes, take the bag out and depress the safety button the vacuum will run. Need some help or direction. Thank you


Try this.\015\012Disconnect hose. Turn machine on and place hand over intake. If it shuts off immediately, first try turning dial on top of machine so largest dot matches up with arrow. Turn on and place hand over intake again. If it still ... Electrolux Vacuums

My beam serenity plus power head shuts off as soon as it hits our carpet. It runs when held off the floor though. Do you know what could be causing this? The only thing that starts it up is the red reset button.


... Beam Industries 2900 Serenity Plus Central System Vacuum

No power Our dyson DC07 was working fine, then we pushed the button to turn it on. It started to run then shut off and now it is like the power is no longer there. I have checked outlets and they all work. Is there a fuse of some kind in this unit?? If so, how would I get to it?


The motor will have a thermal cut out,however chech your plug fuse and the cable as it enters into the off on switch. its known to snap here within insulation..... ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Electrolux Epic 6500 SR canister vacum cleaner. It is nine years old and for the past few weeks it has started shutting off for no apparent reason.The symbol for bag change lights up and it cuts off, but even after I have put a new bag in, it still does the same thing. Do you have any suggestions? There is a little button or switch that the top of the bag fits on. Do you think it could be the problem?


Your machine is probably clogged, look through the wands, look in the bottom attachment, to see if there is anything stuck there. You can also drop a marble through the hose itself to see if anything is stuck there as well. To unclog the hose try hol ... Electrolux Harmony Canister Vacuum - EL6985 Vacuum

Vacuum trips off as soon as started: new bag, free roller, clean filter.


How old is the unit? ... Eureka Smartvac 4870 Bagged Upright Vacuum

When I try to turn on my DC14 vacuum, it won't stay started. I have to hold down the power button while I vacuum. I have checked for clogs and cleaned the filters, still no luck. Any suggestions?


It just needs a new switch under the "on" button...take it in for service it's worth it! ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Canister vacuum keeps turning off, can push buttons on wand handle to restart but shuts off again as soon as you start to move handle


Its sounds like the problem is either the power head wire which when your using it and twisting it left and right, turns it off.. Or it could be in the hose where the connect meets with the unit.Here's a number to call to further assist y ... Miele S548 Bagged Canister Vacuum

Bad Motor? I have an upright Electrolux Prolux Heavy Duty "Appareil Industriel" and the motor does not seem to be working and turning the brush. Is there a trip switch somewhere to try and reset the motor? I have taken the plastic cover off on the base of the unit and cleaned it well, but can't seem to get the motor to start again.


... Electrolux Vacuums

Epio 6500 canister electrolux won't stay running...says the bag is full even when it isn't. Will start but as soon a load is placed on the unit it shuts down. Any thoughts?


There might be something stuck ... Electrolux Epic 6500 Vacuum

After using the vac for 10 minutes or so, the motor starts turning on and off with greater frequency the longer I let it run. Eventually it is on and off so frequently that it has no power. Would this possibly be the 24V relay? I have checked the breaker on the unit and it is not tripped. Does the motor have a thermal overload switch separate from the breaker?


No it dosen't. I fix central vacs all the time and relays usally don't do what you described. They either go out all the way and won't turn on or they will trip and you will have to push the breaker back in. What is probably happening is you have a s ... Electrolux Centralux Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0745 seconds