Having problems with your Vacuums ?
HOW TO CHANGE BRUSHES IN GRACO 3800 TURBINE - Vacuums
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
HOW TO CHANGE BRUSHES IN GRACO 3800 TURBINE - Vacuums
I have a VAX V12 vacuum cleaner which suddenly stopped. The smell indicated Carbon Brush Problems. I contacted a service agent who told me that it was not possible to change the Carbon Brushes brushes on this model and they would need to change the Motor Unit.. To me this sounds very unlikely. Two questions please. Is it possible to change the Carbon Brushes and how do I get the cabinet apart which looks very difficult. I am well qualified electrically to do this job. Regards James Beech
I accidently ran over a sock while vacuuming underneath my bed and the belt broke (brush does not rotate now). I've always changed the belts in my vacuum cleaners, but the Healthy Home manual states that I need to bring it into a shop so that a professional repairman can change it. I find this ridiculous and now wish that I never bought it. How do I change the belt myself? PS I have already bought a replacement belt.
... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue
Hello can you help me please? I have a Kirby G4 vacuum cleaner, It did work ok until it started to give off burning smell and lots of sparks from the brushes. I have changed these brushes, the motor still rotates but it still gives off sparks and burning smell. Do i have to change the motor as well? Can you help please? Thankyou Martin
Some debris, even sand or dirt, probably got into the motor, causing damage to the armature. If this is the case, you will need to replace the motor. The burning smell from the motor is generally a sure sign of a bad motor. ... Kirby G4 Bagged Upright Vacuum
I have a Dyson DC33 bagless vacuum and the beater brush is not turning .. How do I get the cover off the brush to change the belt?
If you lay it down so you can see the bottom of the vacuum, there should be 3 flathead looking screws,just turn them a quarter turn or so, and that bottom should pop off so you can take the brush out and change the belt, just make sure you watch how ... Dyson DC-33 MultiFloor Upright Vacuum Cleaner
Brush on riccar vacuum how to change clutch on brush
The clutch is part of. The rush roll. Remove the brush roll and take the clip off the end to take the brush roll apart. ... Riccar 8955 Upright Vacuum
I have an eureka power plus vacuum floor cleaner and i have no way of opening the botton to the brush to change my belt for the brush since the brush will not turn.
Look for two screws at the edge of the brush housing. You may see these ones on top. They will be black and recessed ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems
Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums
I just purchased a Dirt Devil machine on Monday, I finally got it put together today and the brushes are not moving, dust is swirling around but no brush movement, I have changed all the nap settings, nothing, I am having company tomorrow and I threw my other vacuum cleaner away, HELP ME. Thank you.
Sounds like you may not have the belt attached or it is broke. ... Dirt Devil Vacuums
I have a Hoover Wind Tunnel Self-propelled vacuum. I changed the belts because the brush was not turning. After replacing the belts the brush is still not turning what can be wrong?
There are two belts on the wind tunnel this video will show you how to repair ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
My vacuum does not suction floor debri the canister says change bag, i changed it 2 times with recommended electrolux bags. It will suctionwith wand and brush but not with power head
\015\012The power head has a separate motor to drive powerful carpet cleaning.Check if that motor is getting blocked or if its running slow/weak.Also check from any blockage in vacuum line.\015\012Keep updated with the results.\015\012Than ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
Changed the motor carbon brushes on my Beam central vacuum cleaner equiped with an IntelliWatch system. This system includes the Alutron DB100 module. This Alutron module needs to be reset so that the vacuum cleaner can operate properly. I believe that this module keeps log of running time and disables operation after a predetermined time. Can you help me with providing a reset procedure that will reset this module. Thanks
... Sunbeam Vacuums
I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.
Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums
Change motor brushes on Fein vacuum
If the vaccuum was used with large amount of fine dust , most times the filters are largely shut beaten ,beware also of the electric field look its color to get a indication of the expectation of the remaining running time of the motor. 80% chan ... Fein 9-55-13 Turbo II Bagged Canister Vacuum
How do u change the brush belt - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
Here is a link to the belts you need and a manual you can\015\012view which has instructions:Bissell Carpet Cleaner Belt and Manual ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
How to change brush belt on dco7 dyson - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
This depends on whether your DC07 has a brush control clutch or not. For excellent illustrated guidance go to www.dysonmedic.com and click on DC07. For belt change on a model without clutch click on "belt and brushroll". It's simple! For models with ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
How do i change the brush on my 5770 bissell - Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue
BISSELL model 5770 has a lifetime belt warranty. You can locate a BISSELL authorized service center at www.bissell.com and the belt should be replaced at no charge. ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue
How to open up to change the motor brushes - Miele Vacuums
Http://www.devicemanuals.com/guide/Vacuum%20Cleaner/Miele-manuals.html\015\012\015\012\015\012 I use my camera tak ... Miele Vacuums
How can I change the belt on the kirby vacuum shampooer brush roller. There is no way to snap the roller out and it seems that trying to unscrew the end isn't doing anything either.Model 5584 renovation group is what is written on the shampooer attachment. The kirby is a heritage model 2HD - purchased in the late 1980's.
... Kirby G6 Bagged Upright Vacuum
My Oreck XL was working fine, then when I vacuumed a shag rug is started smoking and smelled like something is burning. (I changed the bag, checked for clogs--none found, and roller brush is turning. It has a metal handle.) Now I am afraid to use it.
Even though the brush is spinning, the belt is probably worn out and stretched. when you vacuum the shag carpet, it puts more drag on the brush. try running it on a shorter carpet or hard floor for a few minutes. if it doesn't smoke, then you know i ... Oreck XL2000 Bagged Upright Vacuum
"CHANGING CARBON BRUSHES ON A DYSON VAC" - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
You dont need to replace with new motor,i just replace the brushes not had no problem yet.. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
How do I change the Brush Belt? - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
It depends on the type of ProHeat cleaner you have. But you can go to www.bissell.com and download the manual for your model and you can get the belt you need at ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
How to change carbon brushes on henry - Henry Numatic "" Canister Vacuum
The brushes are easy to change, follow the directions in your book. ... Henry Numatic "" Canister Vacuum
I have an old upright hoover vacuum. I need to change the belt but can't figure out how to get to it. The bottom plate over the roller brush comes off but I can't get anything else off to get to the other end of the belt.
Model no. req ... Hoover Vacuums
How to change carbon brushes - Henry Numatic "" Canister Vacuum
You need to know that very seldom will new carbon brushes alone `FIX`a motor in todays vacuums as they are higher RPM than those of 30 years ago.On a salvageable motor a good rebuild procedure will generally include repacking bearings, cleaning ... Henry Numatic "" Canister Vacuum