Having problems with your Vacuums ?

SteamVac F7430-900 brushes won't turn - Vacuums


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

SteamVac F7430-900 brushes won't turn - Vacuums


... Vacuums

Brushes wont turn hoover f7412900 steam vac - Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum


... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.


... Kirby Ultimate G Bagged Upright Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi


Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

My Dyson Blueprint bagless rollerball vacuum brush refuses to turn every so often. Everything is connected properly, nothing is clogged in the brush, the vacuum power is turned on and then the brush bar control is released, but the brush still does not turn.


... Dyson Vacuums

Hoover SpinScrub brushes not turning - Hoover V1 SteamVac SpinScrub Vacuum


Hi There,Here's a very helpful Tip that I've written that explains step by step how to diagnosis the Hoover SteamVac when the brushes stop spinning. This will also walk you through how to replace the brush gear turbine assembly if you f ... Hoover V1 SteamVac SpinScrub Vacuum

Hoover steam vac v2, brushes won't turn. - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


Hello,The Hoover SteamVac's are notorious for \015\012this exact problem. There are several things that can be causing this \015\012probelm.First, what you'll need to do is take the brush block \015\012out of the machine. To d ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

The scrubbing brushes do not turn. - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brushes do not turn - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


The brushes are turning by an air driven turbine. The turbine has a \015\012pivot bushing made of steel inside of it that gets rusty because of the \015\012water that is running through it. The turbine will have to be replaced.\015\012 You can fin ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Brushes will not turn - Hoover F7220900 SteamVac V2 Upright Vacuum


Check the belt. make sure it not burst ... Hoover F7220900 SteamVac V2 Upright Vacuum

Hoover max extract brushes not turning - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

The rotary spin brushes will not turn - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Belt either came off or broke ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover f7452900 brushes wont turn? - Hoover F7452-900 SteamVac Upright Vacuum


Make sure that you have it on the carpet setting and not the hardwood/tile setting. also if you used the hose, make sure that the little door is closed. if all checked... remove the recovery tank, there should be a rubber grament on the stand pipe un ... Hoover F7452-900 SteamVac Upright Vacuum

Brushes do not turn - Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum


Check the brush block to see if the shaft that goes into the turbine broke off, replace brush block if it did. If ok, then the turbine may be clogged up, either clean it out or replace the turbine. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Brushes donot turn when asked to shampoo - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


The brushes are turning by an air driven turbine. The turbine has a \015\012pivot bushing made of steel inside of it that gets rusty because of the \015\012water that is running through it. The turbine will have to be replaced. You can find a genu ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Srub brushes not turning - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


You will find broken belt or something is jamming it ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Agitator brushes wont turn - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My brushes are not turning - Hoover F7220900 SteamVac V2 Upright Vacuum


There is a plastic shaft on the back of the block brush (spin \015\012scrubbers),\015\012 these wear out or break. You may need to replace the block brush. Or \015\012if the shaft is not broken it could also be the Turbine Gear. This is \015\012wh ... Hoover F7220900 SteamVac V2 Upright Vacuum

Brushes will not turn - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


(1) Remove the brushes by pulling down at the ends.\015\012Is the square pin present on the top of one brush? It should be approximately 1/4 inch square, and two inches long. That connects the brushes to the drive mechanism.\015\012(2) ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

BRUSHES NOT TURNING - Hoover F7220900 SteamVac V2 Upright Vacuum


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F7220900 SteamVac V2 Upright Vacuum

Brushes don't turn - Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum


I had the same problem and found a manual online. I never realized that there was a filter in the bottom of the machine. There are 2 red tabs, squeeze them together and pull ( I had to use a pair of pliers to pull). Note which is top and which is bot ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

The brushes stopped turning - Hoover F7431-900 SteamVac Vacuum


Just repaired mine today same problem. \015\012Turbine drive shaft which drives two sets of plastic gears and which in turn make the scrub brushes rotate has sealed ball bearings and I guess from an evidently poor design moisture some how enter ... Hoover F7431-900 SteamVac Vacuum

The brushes won't turn. - Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Spinscrub F 7412-900 brushes wont turn - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The brushes will not turn - Hoover SteamVac F5914-900 SpinScrub Upright Vacuum


Be sure the speed switch is set to carpet. Also remember the brushes won't turn until the handle is tipped back. If this is not the problem, remove the brush and insert a flat screwdriver into the square hole the brush pin goes into, and be sure it t ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1979 seconds