Having problems with your Vacuums ?
How do put the belt on for the shampooer - Vacuums
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
How do put the belt on for the shampooer - Vacuums
I have two old identical 5842's that I use in the garage and around the house. The belt broke on one so I bought a bag of 2 genuine Eurika "U" belts, which is the correct belt for this vacuum. They were obviously smaller than the original belt because they were not stretched out. When I put the new belt on it lasted about 20 minutes and then came off. I put it back on and ran the vacuum with the cover off to see what was wrong. Everything looked fine except the belt rides to the outside edge of
Not 100% sure this is the remedy for that particular problem, but I would take the time to clean both of the brushes that the belts operate, one on each machine.\015\012Remove the brushes and clean as best you can. At the end of each brush there sho ... Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum
I have a kirby sentria. vacuumed up my son's headphones and immediately shut if off. took brush off, unwound headphones, put it back together. when i turned it back on, the belt snapped. so i went to vacuum place, got new belt, but when i put it on, with the green arrows lined up, it doesn't have much suction. with the red arrows lined up, it just smells like its burning and i don't want to break another belt! HELP!!
Take the front off the vacuum and check inside both the front portion and the canister for additonal clogs. Sometimes something will get caught in the impellor, causing the motor to overheat. Since there's little suction and the smell, I'd guess th ... Kirby Generation 3 Bagged Upright Vacuum
I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o
I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum
For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.
... Kirby Ultimate G Bagged Upright Vacuum
The belt on my vacuum cleaner model 6596 bissel powerforce bagless turbo keeps breaking. As soon as I put on a new belt and start it up the belt snaps. It is the durabelt meant for this vacuum model. Also, my son has been having the same problem with his. He has the same model and same belt. This problem is occurring even after a thourough cleaning.
I would guess you aren't centering the belt correctly, thus it's edge is caught between the brush and another solid object, causing the breakage.\015\012When you get the belt on the the brush and the brush back in place, turn the brush a few ti ... Bissell 6596 Bagless Upright Vacuum
Oreck vaccum when i put a new belt on, the belt rubs the side of the wall of the vacuum gets real hot and busts. is there any type of washer fitting that goes on the vacuum to hold the belt in place? i dont know i need help thank you. you can reach me at [email protected]
The belt must not be running true to the pulley. You may need a brush roll, but also check the motor to make sure it isn't moving inward after the belt is put on. ... Oreck XL Ultra Bagged Upright Vacuum
Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430
Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum
I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.
... Windsor VS14 Versamatic Bagged Upright Vacuum
My oreck upright smells like rubber burning when i vacuum. i just put a new belt on but it smelled like that before i even put the belt on
... Oreck XL Ultra Bagged Upright Vacuum
Vacuum belts how do i put a new belt on my vacuum?
I can't do it ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
I need to change the belt on the shampooer. the shampooer doesn't come apart like the vaccuum unit. i can't get the brush off so i can put a new one on.
This will help...\015\012\015\012http://reviews.ebay.com/CHANGING-THE-BELT-ON-A-KIRBY-G3-G4 ... Kirby G5 Bagged Upright Vacuum
Belts I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do t
It is the flat belt that gets stretched and should be replaced at least every 6 months. The V belt wears down so it won't it right in the brush roll V. Maybe the belt tensioner wheel has a problem, sometimes they get hook up and won't engage the V ... Vacuums
The Belt on my Dirt Devil broke...so I purchased another belt and as soon as i put it on and started to vacuum it also broke, i noticed that the metal piece the belt goes on was extremely hot and was melting the belt. Whats wrong with it?
It may be that the beater brush is bound up . This will cause slipping, of the belt. Take out the brush and clean out the bushing . Hair gets wound up in side. once you have it cleand out. Put a few drops of cooking oil in side the bushing on both e ... Dirt Devil& Breeze Vision Canister Vacuum Vacuum
My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc
... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
Trying to replace belt on hoover convertible bagless upright u8188900. belt replace # 38528-049. i have opened vacuum and put belt back on, but it will not get tight enough around the motor gear and the brush spool to be able to activate. am i missing something? mike
... Hoover Vacuums
We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a
Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums
My Eureka Maxima isn't working right. The belt is spinning fine until I lower the handle to start to vacuum and then the belt stops spinning. As soon as I put the handle back in the upright position the belt spins again.
Sounds like belt is worn try changing belt. ... Eureka 4700A Maxima Bagless Upright Vacuum
Belts I have recently bought new belts and when I installed the green light only comes on sometimes and I can smell rubber burning. The last belt broke very quickly so I am assuming that when I put the vacuum back together I am doing something incorrectly. Can you help instruct me?
Recently received a kirby from mother in law and don't how to change the belts ... Kirby Ultimate G Bagged Upright Vacuum
I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?
If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums
I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do they re
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=675093\015\012Generic problem for all Vacuums\015\012I have a Hoover self-propelled\015\012Posted by kl ... Vacuums
How do you put a Hoover runabout belt on vacuum
I found this on another site and it worked for me. RonL\015\012\015\012Looking at the brush, remove the two screws from the black plate holding the brush. There are two clips that holds this plate once you remove the screws. This should ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Have eureka 9734 replaced belt, put back together,brush rotates well but vacuum is not picking up anything, no suction.
It sounds like the machine is clogged. Check the port behind the belt and any and all hoses for obstructions and remove. ... Vacuums
Putting on a belt on a vacuum
Greetings from GoVacuum.com,Replacing a Belt on an Upright vacuum can vary from model to model, but it is basically going to be the same for most upright models. First you will need to access the belt. Most upright vacuums t ... Vacuums
Son took the front plate off the kirby heritage II vacuum thinking that was how to replace the belt, now don't know how to put the three rings and belt catcher back on?
Looked at a kirby vacuum that a family member has and saw how it was assembled! Thank You ... Kirby Heritage II Vacuum