Having problems with your Vacuums ?

Need to replace main drive belt for sickle bar


Answers :

Instructions
\012\012

Put on your work gloves. Check the frame size for your mower. It will\012either be a 56-inch frame mower or a 76-inch frame mower. When you have\012determined the frame size, adjust the tractor's rear wheels to the mower's\012frame size. For 56-inch frames, adjust the rear tractor wheels to 56-inch\012centers or less. The same rule applies for 76-inch frames.
\012\012

Back the tractor into a position where you can align its left lower link\012to the mower's lift link pin. Attach these two parts together and secure the\012connection with the tractor linchpin.
\012\012

Roll the tractor and adjust the leveling crank until the tractor's right\012lower link can be attached to the right link pin on the mower. Use the tractor\012linch pin to secure the connection.
\012\012

Attach the upper link from the mower to the lower hole in the tractor\012rocker arm by using the link pin.
\012\012

Start the tractor. Using the hydraulic control lever, lift the mower\012frame assembly slightly and move the mower to the left to allow attachment of\012the left stabilizer. Place the stabilizer guide under the tractor's left lift\012link. Position the clamp over the link and tighten the nut firmly
\012\012

Depending on the tractor type, install the clamp plate or push rod\012anchor assembly onto the left lower link. Install the push rod on either the\012clamp plate or anchor assembly.
\012\012

Shift the mower assembly to the right to attach the right stabilizer.\012Place the stabilizer guide under the tractor's right lift link. Position the\012clamp over the link and tighten the nut firmly.
\012\012

Raise the mower using the hydraulic control, then attach the mower lift\012spring to the spring links with the pins that have been provided. Lower the\012mower assembly and turn off the engine.
\012\012

Remove the tractor power takeoff (PTO) cap and connect the splined end\012of the mower's drive shaft to the PTO shaft. Secure the connection with the\012snap coupler found on the yoke.
\012\012

Rotate the leveling crank to lower the frame, ensuring that it is\012parallel to the ground. Use the leveling crank lock to secure the crank lever.

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need to replace main drive belt for sickle bar


Instructions\012\012Put on your work gloves. Check the frame size for your mower. It will\012either be a 56-inch frame mower or a 76-inch frame mower. When you have\012determined the frame size, adjust the tractor's rear ... Vacuums

How do I replace the drive belt on a kirby G4? Actually the belt is already replaced I just need to know how to reattach that front part back onto the main vacuum. HELP


Greetings from GoVacuum,\015\012\015\012Here's a video we shot showing you in detail how to install a belt properly, and how to reattach the head properly. I hope this helps you;\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum

I replaced the agitator bar drive belt on a Hoover Model U6432-900 upright vacuum cleaner, but it just slips when the drive wheel is spinning. Is there an adjustment I need to make? I don't see any adjustment spots.


You probably should have replaced the flat belt(38528035) also. But the drive belt has a idler wheel(#13) to engage it, is it riding on the belt, if not if may have jammed to one side and able to spring up against the V belt. It could have broke al ... Vacuums

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The Panasonic MC-V7515 has two belts. The local vacuum repair guy says he only has a part number for the drive belt, which is UB-9. How do I find a replacement for the other belt, the one which directly drives the beater bars? By the way, this vacuum has great suction, but otherwise is far inferior to my previous Panasonic vacuums. The cheaper models aren't a good buy--stick with the more expensive models.


... Panasonic MC-V7515 Bagged Upright Vacuum

I have a Kirby G5 and need to replace the gear drive shaft, as the lever inside fell off and the shaft came out. (Common problem by the sound of it.) How do i remove the actual gearbox itself. I have removed the 3 screws on the bottom, but it's not coming out. What's stopping it from coming out? Do i need to remove the gearbox drive belt first? If so, how do i get to it? Thanks in advance.


HELLO, JUST USE THIS GUIDE! :0)http://reviews.ebay.com/REPLACING-OR-REPAIRING-KIRBY-VACUUM-NEUTRAL-DRIVE-PEDAL?ugi ... Kirby G5 Bagged Upright Vacuum

Need a replacement drive belt for my hoover lark u4043 not sure about last no. it's an old machine, but this one is in perfect condition, minus the drive belt. my local vacuum specialist says they can't get them anymore. where can I get one or a suitable alternative?


HiAs you know the Hoover Lark was more or less a rebodied Hoover Junior. The U4043/ (are you sure its not U4034?) model should use the same round drive belts as the Hoover Junior 1346 so youre looking for the old rubber ring type belts which ar ... Vacuums

How can determine when it's time to replace the drive belt on my Bissel Power Steamer? Is there a certain number of hours of usage that I need to keep track of or does the belt replacement depend on the type of carpet I'm cleaning? Thanks, Jim


Usually, replacement is needed when the brush no longer runs or is intermittent. Check the brush bearings and for debris build-up whenever the belt is changed. Good luck! ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Belt replacement Hello, The belt that drives the beater bar on my Dyson DC-07 just broke. Is it that difficult to replace it or should I take it somewhere. Thanks!


It's a fairly simple job. The belt just loops over the end of the beater bar and motor shaft. Need to take the cover off the beater bar housing to get to it. Most difficult part is stretching the belt while putting the beater bar back in the housi ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Panasonic mc-e4113 Upright vacuum. The belt that drives the brush in front is broken I have found a spare for this but there seems to be a pulley missing on the main drive shaft that the belt needs to fit on. I can't believe that there wouldn't be one? Can anyone tell me if this is the case and if so where I can get one from. Many thanks Sean


... Panasonic Vacuums

How to replace main drive belt Hesston pt7 haybine


... Vacuums

I need instructions on replacing the belt that drives the brushes on a Bissell powersteamer pro deluxe carpet cleaner. Could the broken belt have anything to do with the suction of the cleaner?


Here is a link to the belts you need and a link to the manual:Bissell 1697-7 Manual and Replacement Belts ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Need to replace the main belt on my Bissel 1698-P. Can't figure out how to get the belt around the brush roller. Have the top off. Cleaned the water tubes, didn't let the water come down.


Remove belt access door at left front of unit.\015\012\015\012Unplug the unit. Remove the two solution tanks.Remove spray tips from guides.Remove the brush and cog belt by removing the screw from the orange retaining collar.\015\012Remove belt ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

I just put a new belt on my boss 4800 and it is to loose? Does the beater bar needed to be replaced? There is no traction to turn the belt, it spins


Sounds like the belt is to big you didnt replace with the correct belt ... Eureka Smartvac 4870 Bagged Upright Vacuum

I need to replace belt-drive cog belt - Eureka Vacuums


Go here > http://www.eureka.com/en-US/Vacuums/Accessories/Belts/ ... Eureka Vacuums

Need replacement drive belt for tempest Z178 cannot locate a supplier. any assistance please?


... Electrolux Vacuums

The self propelled feature does not work. Belts are OK but the drive wheels do not seem to be engaging. Is there a cable or something from the lever on the handle that needs to be replaced?


My vacuum cleaner does not turn on \015\012could it be the motor out \015\012i check the switch it ok not getting any power to the switch ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hello. I have an electrolux glider upright bagless vacuum cleaner (UK model) who's brushes do not rotate any more. I'm guessing that I need to replace the drive belt but I have no idea where to start. I would appreciate any tips. thanks


Hello! There are two solutions to this as the Glider model you speak of could be the more old fashioned type where screws on the bottom foot plate (ie where the spinning brush sits) have to be undone in order to get to the drive belt.\015\012 ... Electrolux Vacuums

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n


From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

How to replace main drive belt on dyson dc03 - Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum


... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

I need to replace drive belt on dyson dc17 - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


Here is a link to the belt you need and a manual you can view which has instructions: Dyson DC17 Belt and Manual ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

NEED TO REPLACE DRIVE BELT ON HOOVER VACUUM MODEL TURBO 3500


Take off the brush roll cover, then take out the screws from the bottom to remove the top lid, the belt goes from the brush roll to the motor shaft. ... Vacuums

I need instruction on how to replace the drive belt.


First unplug the device...depending on the model you have there are two screws that hold the cover onto the unit. sometimes they are hidden behind the rubber wall guard and sometimes they are hidden in the random designs on top or even the bottom of ... Vacuums

My vacuum has not been running right..the beater bar is not picking up and the rollers aren't spinning...the belt doesn't need replaced so what else could it be...everything else seems to be running fine???


The motor shaft that spins the belt may have hair wrapped arount it, causin the belt to slip. You can't miss the burnt odor.\015\012Remove the belt and clean the motor shaft. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0957 seconds