Having problems with your Vacuums ?
Vacuum was working fine one day, next day it won't come on
You can try doing this first, plug it in to your outlet and switch it on. If it will not start, try to move the wire near the plug to see if the problem is a lose wire in that area. If it responds in moving the wire you have to replace the plug of your vacuum. Message me if you need further assistance. Thanks..
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Vacuum was working fine one day, next day it won't come on
You can try doing this first, plug it in to your outlet and switch it on. If it will not start, try to move the wire near the plug to see if the problem is a lose wire in that area. If it responds in moving the wire you have to replace the plug of yo ... Vacuums
Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad? My Kenmore Progressive won't turn on today either -but was fine last week. I cleaned the filters checked for blocked air, tried a different outlet and no luck. I'll check the pins on the connections and see if one of them is not matching up or appears worn.
Give the prongs a wiggle and see if there is any play in them.Might just be a plug end. ... Kenmore 25512/ 25513 Progressive Canister Vacuum
Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad?
My first recomendation would be to try pluging into a diffrent wall outlet as well as something that is on a diffrent circut . It is a known problem that the pins inside that make the connection could be worn out . There are several pins from the one ... Kenmore 21513 Vacuum
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum
I have a Tristar cannister vacuum. One day it's fine, the next day it won't turn on. Nothing unusual happened to it in the meantime. I don't thinks it's the motor, because when I took
... Tristar Vacuums
I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha
... Eureka Smartvac 4870 Bagged Upright Vacuum
Miele classic vacuum,wont run, tried pressing restart.Was working fine earlier in day. When cord retracting the 1200 watt setting light on top of vacuum came on for a split second.
Vacuums have a heat activated breaker in them. Is the action end hot? If you get a clog, the motor won't get the air blowing through it and it will overheat causing the breaker to blow. If this is the case, wait (sometimes a few hours) for it to cool ... Miele Vacuums
I have a Polti leco aspira 710. The water in the tank is heating but when the trigger is activated no steam comes through. The machine is showing one green light and is emitting a continuous beep. The vacuum cleaner is working fine - but no steam at all
... Polti Vacuums
Suction vacuum one day fine next not having great suction picking up big things but not feeling that deep down suction rolling too too easy changed bag, belt and cleaned roller it is like it is gliding over but not really getting deep visible cannot even tell I went over carpet
Don't panic! Easy fix!\015\012\015\012I was having the same problem, but I removed the base plate from the bottom of the vaccum (5 screws on mine), revealing the roller and the engine. Just behind the roller is an intake tube. Mine had ... Oreck XL Ultra Bagged Upright Vacuum
No power My Hoover S3765-040 WindTunnel Bagless Canister Vacuum does not seem to receive electricity to power the vacum. One day it worked and the next it did not. Any recommendations for a solution.
... Hoover S3765-040 WindTunnel Bagless Canister Vacuum
My delonghi ec330 espresso machine. it worked fine for a while until one day i forgot to turn it off and it was on for about half the day.later i tried to use it, and the espresso comes out drop by drop now.
Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio
Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum
I purchased a brand new Eureka Pet vacuum, sorry don't know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
If the motor is running, there should be suction. Possible problems depend on whether it's a canister or upright and are:\015\012A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out ... Eureka Vacuums
Pickup water wont pickup the water after putting it down very little comes up into the tank .it worked fine when we baught it but after not useing it for some time it worked now it wont **** water up at all can anybody help.
The clear shroud covering the front of "hood" has two sheet metal type screws at the bottom in front of the brushes, these two screws also hold the little straight brushes ( one on each side) in place. I found one of these screws had broken it's plas ... Hoover F6020-900 SteamVac Upright Vacuum
My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u
Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums
Dyson suddenly stopped working. About a week ago it had a suction issue. One of the upright tubes was clogged, cleared it and it worked fine. Today I was vacuuming and it simply powered off. The vacuum is maybe a year old give or take some.
Hi its Darran at Dyson.Sorry to hear you are having difficulties with your Dyson. So that we can help, please contact our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US). One of our advisors will be able to run through some ... Dyson Ball DC24 Bagless Upright Vacuum
Vacuum I have a dirt devel purpose for pets vacuum. It has worked well previously. The vacuum has started spitting out debris from the bottom when slightly lifting from one floor to the next. What could be causing this. Thank you
You may have a clog in the dirt inlet by the brush roll, and also the hose. ... Vacuums
My electrolux oxygen vacuum cleaner shut off and will not turn back on. It's less than a year old, but I bought it off Craig's list--they were the orginal owner and they said they bought it in May of 2008. I've only used it a few times and it worked fine except for the last time when it suddenly just shut off. I thought maybe it had come unplugged and I didn't really worry about it because I was finished vacuuming. But, I went to use it tonight and it would not turn on at all--no lights, nothing
No..Electrolux is really great about warranty service. They will help you even though you are not the original owner. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
I have 2 emerson stinger wet dry vacumes that i purchased at home depot. both stopped working. not the day used them, but the next day when i plugged them in they did not come on. is there a fuse in these or have switches problems?
Return them to THD, if you paid with credit card they can scan your card and find your proof of purchase , even if you dont have a receipt. ... Vacuums
My Shop-Vac 5870400 was working just fine, and then one day while i vac the floor its just stop working, tried to turn on/off a few times, swicth to different outlet. i did even tried to open it, but found no burn or anything that suspicious. i never drop nor used outside, only inside the house for normal vacumm. please help. thanks.
Same thing just happened to mine. My solution is to get another one but a different brand. I think it should have lasted longer than four years of fairly light usage. From what I read, if it does as we both described, the motor is shot and not wor ... Shop Vac 587-04-00 Canister Wet/Dry Vacuum
Warning Light What does the light mean on the canister that has two prongs on one end and one on the other. The vacuum works fine but the light is on. I changed the bag and filter.
Check the hose and wands for a clog. Usually that light means a full bag, but a clog or restriction will also cause it to come on. ... Electrolux Epic 6500 Vacuum
My bissell vacuum attachments wont work, as soon as i attach anything besides the crevice tool it wont ****,but sucks fine when its just the hose
Tern upside down remove plastic cuvier look wear the hose gos fillip skew driver ... Bissell 6594 PowerForce Bagless Upright Vacuum
I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...
The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
Stopped working Was working fine then it smelled like burning rubber, not the belt I checked. It sounds like the motor wants to run then it just stopped but the light is on. What do you think, go by a new one?? This has been a great vacuum cleaner and I can not seem to find a Sharp anywere. Thanks for your time.
Well it could be the motor, if it is it would cost around $80 or so for a motor. May be better to buy new, thre are a number of good brands out there. ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum
Let's try this again. The main vacuum and hose works fine, the "foot" does not. When I turn it on, it shuts off automatically and the light comes on telling me to "check brushroll". I did this and removed all hair, strings, etc., Still won't work. Please respond. The last post took over 30 minutes with no response.
Sounds like you have hair or carpet buildup in the roller and it is not freely rotating and you are getting an error. If there is no buildup, then roller bearings may be frozen up, or the unit has a faulty capacitor and is not going to work due to el ... Vacuums