Having problems with your Vacuums ?

Beater brushes sometimes work and very often not. Hoover windtunnel bagless and beltless

Answers :

\015\012Generic problem for all Vacuums
\015\012Beater brushes sometimes work and
\015\012Posted by patarmao on Jul 14, 2008
\015\012Beater brushes sometimes work and very often not. Hoover WindTunnel bagless and beltless.
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. Your problem is that you may need to change the belt every 4 to 6 months as a recommended belt change on the vacuum and also keep an eye on the brushes or brush strips, they also help in the vacuum working properly. Here is a typical belt change on a Hoover. Normally there are screws, clips or levers that would remove the bottom plate or if that does not work then the top cover will come off and that will expose the belt. Once that is off and the belt is exposed then cut off the old belt and then lift up the brushroll on the pulley end and install the new belt around the pulley end and re-install the brushroll. Then use a belt puller or a screwdriver with a bent right or left end to stretch the belt onto the motor pulley and then track the belt in a straight line and reverse you steps in the reinstall of the top cover or bottom plate. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

\015\012http://www.hoover.com Telephone
Contact our Customer Service Department at 1.330.499.9499
Monday through Friday
8 a.m. - 7 p.m. EST

\015\012Thanks, Don the Vac Man
Go Ahead. Use Us.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Beater brushes sometimes work and very often not. Hoover windtunnel bagless and beltless

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783732\015\012Generic problem for all Vacuums\015\012Beater brushes sometimes work and\015\012Po ... Vacuums

The beater bar on my hoover is not working - Hoover U6630-900 WindTunnel Bagless Upright Vacuum

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Brush on underside not working, please help. - Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Turn the unit over and remove the four screws that retain the bottom plate over the agitator. Remove the bottom plate and see if the belt of off or broken. The belt part number is printed on the data label for the cleaner. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Beater brush will not work - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Have a Hoover model S3670 and the beater brush no longer spins. Have checked the beater belt and it is good, did find out that the light bulb in the unit was bad. Any suggestions on how to test the motor that drives the belt or determine the reason the beater brush is not working?

I usually test the motor with a cord with alligator clips on the wires, and attach them to the black and white wires on the motor ( remove the belt first ). A very common problem with this model was a short circuit developing in the short cord that r ... Hoover Vacuums

Windtunnel first one used 6 times beater bar stopped working, took apart cleaned and belt was fine. this one had a reset switch for beater bar. had insurance at best buy so returned for a new one. used 2x beater bar not working and not dirty, no reset switch on this one., now back to the store for another? i don't even want the same one. I wonder how many they are gonna give me. This seems to be a common occurance.

Sorry, you feel like that. I have rentals and 6 windtunnel's (I prefer the bagged ones) and have never had a problem such as you have described. I think Hoover makes a great vacuum. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I replaced the beater brush and works on carpet but when I turn the beater brush oof to do floors, the vacuum shuts off.

... LG Electronics Kompressor Pet Care Upright Vacuum Cleaner LUV200R

Beater bar brush stopped working...

Does the power head motor stop, or does the brush roll stop. If it is the brush roll stopping, replace the belt and/or the brush roll. If it is the motor, you may need to clean out around the motor, it may not be getting enough air to cool causing ... Rainbow E series Canister Wet/Dry Vacuum

My Dyson Blueprint bagless rollerball vacuum brush refuses to turn every so often. Everything is connected properly, nothing is clogged in the brush, the vacuum power is turned on and then the brush bar control is released, but the brush still does not turn.

... Dyson Vacuums

Kenmore 35923 beltless brush not working after rolling up shlace.

Its due to the grip of the brush and the motor not getting fit its became little bit like streched so this happens and in this case replacing the brushes and checking any other component broken near to it is necessary. ... Kenmore 35912 / 35913 Progressive Upright Vacuum

My shark bagless sweeper worked for about 6 months. Like a previous blogger, I caught the edge of a rug that jammed the sweeper, three red lights blink, the brush is free moving yet the sweeper will not work. I did leave it plugged in all the time otherwise it would not run but for minutes. Very disappointed. New battery? what if that doesn't work? is it junk then, money down the drain.

This will probably cost you more to repair than to buy a new one. Does it turn on at all? ... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou

Try this link belowhttp://www.ereplacementparts.com/hoover-u6630900-windtunnel-selfpropelled-bagless- ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Brush works intermittedly - I've looked at the common solutions listed but none seem to work...shaking it & reseating the canister will get it working again sometimes but obviously that doesn't seem to be a very good solution. Can you help?

I just had the same problem. I would turn on the vac, and it worked fine. When I turned on the brush it would work for a few seconds then shut off. Through troubleshooting I found out it had nothing to do with a bad power connection. By chance I took ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Belt drive not working. Won't turn beater brush.

You need to replace the belt. Here is the belt you need and the manual which has instructions: Dyson DC07 Belt and Manual ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a kenmore beltless upright the beater brush dosetn spin

If it is direct drive then the motor or the wireing to the motor are bad. If it is gear driven then the gears are probally stripped. ... Windsor SR12 Sensor Bagged Upright Vacuum

I have a Dyson DC33 bagless vacuum and the beater brush is not turning .. How do I get the cover off the brush to change the belt?

If you lay it down so you can see the bottom of the vacuum, there should be 3 flathead looking screws,just turn them a quarter turn or so, and that bottom should pop off so you can take the brush out and change the belt, just make sure you watch how ... Dyson DC-33 MultiFloor Upright Vacuum Cleaner

The belt on the beater brush is too loose and the brush won't turn, I have ordered new belts and it still doesn't work!!

Look in your manual for the proper routing of the belt, there may be piece broken and missing without you realizing it. If this not the case, there has to be some kind of adjustment on this unit. ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced

There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.

... Hoover U6485900 Bagged Upright Vacuum

Beater bar not working. suction not working - Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Check for a broken beater brush belt.\015\012Clean the beater brush, clear of all debris and add some WD40 at each end where the rubber holders are. Turn beater brush by hand to work the WD40 into the axle.\015\012Reassemble making sure the belt is ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Dyson dc15 bagless upright. my brush bar is not working but if you use the hose it works .

\015\012http://www.espares.co.uk/datastore/ProductManuals/350256.pdf\015\012\015\012Check the above link to see if it h ... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

I have a Eureka The Boss Mini (Model # 442) vacuum cleaner. It is not working properly sometimes Today I did a cleaned the roller brush thoroughly and powered it on to see if it spins at all. It spins only in Carpet model, but stops sometimes. Please can you tell me what could be the problem?

... Electrolux Vacuums

Hi,My agitator brush won't run on my hoover S3590, I changed the belt, that didn't work. I don't see a possible cause in my book except replacing the belt. I think there could be a short, the brush will come on sometimes when pulling back and slightly lifting. Any ideas would be great and can I fix it myself? Thank you for any help, Bobbie

Hi Bobbie\015\012Take apart the electro floor head if you can and inspect inside - it may well be that there's clogged dust preventing the brush from turning and also check both sides of the actual beater bar as thread and tangled hair can often lead ... Hoover S3590 Bagged Canister Vacuum

My beater bar is not turning so the vaccuum is not picking up. The belt is not broken. The motor is working and I can see the cyclone effect in the canister. I have checked for blockages. I have cleaned the hair and string from the beater bar brushes. What should I do?

You need to replace the belt, it has probably broken. Your actually supposed to change them yearly. Here is a link to\015\012the belt you need and a manual with instrutions: ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1377 seconds