Having problems with your Vacuums ?

Oreck xl9100 runs okay when upright but when the handle is at an angle the motor stops

\015 This problem just started when there were no other problems and the inners had not been touched. Any ideas\015

Answers :

You must test the power cord for open or break use the VOM
2) Test for main switch some wires loose, or bad solder, or switch defective, and replace.
3) Thermal fuse, loose, or bad contact. tight.
4) See if the belt is sliping or broke or worn and replace.
God bless you
7_28_2012_10_42_04_am.jpg7_28_2012_10_42_21_am.jpg
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Oreck xl9100 runs okay when upright but when the handle is at an angle the motor stops


You must test the power cord for open or break use the VOM2) Test for main switch some wires loose, or bad solder, or switch defective, and replace.3) Thermal fuse, loose, or bad contact. tight.4) See if the belt is sliping or broke or wo ... Vacuums

The Oreck vacuum motor sparks the stop running. Plugged to another outlet, the motor did the same things, run for few seconds with sparks and stopped again.


... Oreck XL2200 Bagged Upright Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi


Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?


The same thing happened to me about a year ago with this very model. \015\012The issue on mine was a small, copper-colored metal wheel that attaches to the end of the brush roller. You'll need to remove the top cover (there are several screws). ... Eureka Smartvac 4870 Bagged Upright Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.


It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a VX3000C Broan vacuum and the motor sometimes runs lower and comes back to normal time and time. Plus, now it lamost stops before coming back to normal speed. Can someone explain to me what that might be or if it did happen to someone else? It doesn't stop, but runs at very low speed and come back. It is like if a connection is not made properly. But it does the same at my 3 connections and I did check the one on the vaccuum itselfs.


... Broan-NuTone VX475 Bagged Central System Vacuum

How to replace motor on oreck xl upright - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

I have Nutone VX550C. Motor runs intermittently (cycles on and off rapidly--the light on the handle is blinking furiously) when I use the on/off switch on the hose. This happens at all of the wall connectors, so suggests a hose contact problem. Motor runs continuously when I turn it on at the switch on the wall unit.


The unit does have a switchs the PVC outlets, and it sounds like the hose mech to operate the switches is broken, and intermittently making contact. A replacement hose would likely fix the problem. Looked them up on the net, and they're not che ... Broan-NuTone VX550 Bagged Central System Vacuum

Burning smell While using the vacuum, the running light will get dim. If I hold the handle at the point where the light gets dim the motor will start smoking. I can either raise or lower the handle and the light will brighten up and the vacuum will run fine. Any ideas???


Hi theres two things that could have made it start doing that 1 the whires have a short in it or 2 the motor has gon faulty. you might want to buy a new machine ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have an older Oreck XL vacuum that sounds like it is running twice as fast as it should. I disassembled the entire vacuum, including disconnecting the motor wires, to clean out the hair, string, and other things. When I put everything back and connected all the wires, everything appears to work, including the light. The only problem is, it sounds extremely loud like the motor is running too fast. The model number is: XL3610HH Ser. No. 3610HHXA039740-6 I do not have as electrical diagram to see


... Oreck XL Ultra Bagged Upright Vacuum

Dyson 28 handle is stuck in the locked and upright position. Vac runs fine, just can't get the handle to release to run the vac


How do you remove the air duct (plastic sliding piece) that is making the vacuum stay in locked upright p[position? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

DT 1300 As I am vacuuming the motor seems to fade in and out and sometimes stops running for a few seconds and then resumes. If I move the hose a bit near the vacuum end, it runs smoothly again. Does this sounds as if there might be a short in the motor? Would this be something I can fix myself or does the vacuum need to go in for repairs.


... Oreck DutchTech DTX1300C with Motorized Carpet Brush Bagged Canister Vacuum

Motor loud I have a dyson dc17..recently when i turned it on and pulled the handle down to vacuum the motor was very loud..put the handle in the upright position it is quiet.any suggestions?


When you put the handle down it turns on the brush roll. you may need to clean the brush roll or replce it if the bearings are bad.also clutch and 2 belts are started when putting handle down for brush operation. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

Brand new LG LUV200r used 10 minutes now after removing dust tank & reinstalling the vacuum motor does not run only the beater bar??? I have located wo circuit breakers both seam to be set. This suction motor should run when the switch is pressed & the beater bar should operate when the handle is moved down??? Not A happy customer will return unit to Best Buy only 100 mile round trip!!!! RDH


... LG Electronics Kompressor Pet Care Upright Vacuum Cleaner LUV200R

Bissell Powerwash Proheat. model 1698-j, 220-240v, 50/60Hz, 1200-1400w. Motor stopped suddenly (ident label specifies type Ametek 119464-02), supply inline fuse at motor ruptured, fuse replaced but motor sparks like an angle grinder at armature and blew replacement fuse. Where can I obtain a replacement carbon brush set for the motor. UK based


... Bissell Vacuums

My Discovery 4210 Roomba will run normally for about 20 minutes on a smooth, wooden floor. It then begins the following sequence: run forward a few inches, turn in a tight counter-clockwise circle a few revolutions, stop, power off a few seconds, power up, repeat cycle from forward run. The sequence can be repeated seemingly endlessly if I don't turn off the power manually. I've replaced the motor, and led revolution sensor system on the left drive wheel. I've blown the dust out of everywhere. A


This robot vacuum has a electronic micro processor that controls the unit and tells it how to operate and where to go based on programmed parameters. It's quite a technical marvel. I have dropped a link here for contacting the company tech support li ... iRobot Roomba 560 Robotic Vacuum

Sears 116.31913 Lower units, vacuum motor and agitator power head do not have power/115v to them and won't run. I'm trying to take the handle apart to access the on off switch. I've taken all observable screws out and cannot separate the handle and section immediatly below the handle to access the on/off switch, to trouble shoot. Any tips for separating the plactic pieces enclosing the on/off switch?


... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

My Air Vac is 20-21 years old. Recently it stopped running. I found the fuse by the motor was blown and replaced it. It blew immedicately when I turned it on. I think I need to repace the motor. Do you agree and can I buy a motor from you.?


If the fuse does keep blowing yes you do need to replace the motor. I am sorry we do not sell parts though. Try the link below to get the motor.\015\012\015\012 ... M&S Systems Vacuums

My Oreck Upright will not stay upright! The handle falls over everytime I leave it stand on its own.


What you are in need of is what they call a detent. There is a possibility that is has broken off from the housing which means that the only way to repair it properly is to replace the entire housing. It may have just had the screw come loose and h ... Oreck XL® Classic Bagged Upright Vacuum

DC 17 UPRIGHT BRUSH MOTOR WONT STAY RUNNING. TURN


Have a look at the filters first as it sounds like you blokeage ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a kenmore upright model 116.36933 vac. motor wont stop unless i pull th plug the buttons work on everything else but stopping the vac


... Vacuums

Oreck upright handle falls over


... Oreck XL Ultra Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0744 seconds