Having problems with your Vacuums ?
I want to open the motor of vacuum cleaner model Samsung SC5991....how ?
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I want to open the motor of vacuum cleaner model Samsung SC5991....how ?
On my Air Vac model AV425A Central Vacuum System, I discovered the circuit breaker opened. When I close it, the vacuum motor goes on. It doesn't matter which position the on/off switch is on, it runs until I open the circuit breaker again.
... M&S Systems ZX7000 Bagged Central System Vacuum
Motor quit working. i was vacuuming and all seemed fine. then the motor went really low. when I opened it I noticed that the bag was not attached and the cannister had filled up with stuff and the filter was full. the vacuum will not run now.
My friend, the dirt you sucked up went right into the motor and it burned up. I am very sorry to tell you this. It is probably not worth repairing unless you are able to replace it yourself.\015\012\015\012In addition to not being able ... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum
Need technical help for my miele s2180 momentum canister vacuum .Bought a display open box at fure shop..Came with a filter bag..there are no tears in the bag...Perhaps they put the wrong bag..Anyway after 30 minutes of use..The motor stopped working ..so I opened up the unit only to see,.the dirt was everywhere inside the vacuum...only a little was in the bag itself..can you hepl..Dave
Miele S5000 (revolution 5000) vacuum cleaner - How do I open the casing? When the power button on the handle is pressed the green power-level lights on the handle light, but the motor sounds like it gives a little 'jump' but nothing more. The orange power light on the body also dims. I assume the motor or fan is jammed, but I can't open the body to find out. I've taken out to screws inside near either end of the handle, but to no apparent effect. I'm assuming the body is held together by plastic
My Ergospace Vacuum took some apple juice in and now it makes strange noice and even threw out some sparks. Is there anything I can do my self or is it over with this vacuum cleaner? I opened 6 screws, but I still can't open the motor cover. Are there some hidden screws?
Liquid plus electrical parts always ends up with the electrical parts losing. Juices, although they will dry, will leave behind a sticky residue. You'll need to replace at least the motor, but due to the other electrical components, probably be bet ... Electrolux EL4100A Ergospace Cannister Vacuum
My lux 7000 has a new bag but when i start to use it with the power unit or without the unit shut's it self off i can reset the lites or the motor if you will by clicking the on off switch 4or 5 times and i'm ready to go again untill you start to work and off it goes you can repeat the switch thing as long as u want, it just won't let u vacuum ,it turn's it self off .I blew it all out but found nothing in it. if u don't try to vacuum it will run as long as u want to listen to it. Can you
Have you replace the afterfilter? It may also cause this if rather dirty. It's located under the tool caddy/air diffuser on the back half of the machine.\015\012Try this: Disconnect hose, turn on vacuum. Does it continue running? If so, pl ... Electrolux Lux 7000 Bagged Canister Vacuum
My electrolux epic 6500sr vacuum has a seized motor. How do I acess the motor to service or change it? There are no obvious screws or clips to open the motor outer case
Miele Cat & Dog vacuum gets VERY hot and is VERY loud. Hose has no restrictions and I have changed the dust compartment (motor) filter and the exhaust filter. It still gets hot when I run it with the top open and all filters removed, so I'm guessing the problem is with the motor. Should I be going into the motor compartment? If so, what am I looking for?
Hi\015\012\015\012The fact that it gets very hot could be due to a number of issues.,but the fact that it started making a very loud noise at the same time suggests that there might be more problems maybe brushes etc.\015\012\ ... Miele S514 Solaris Bagged Canister Vacuum
Can't open Cannister Vacuum to get to motor
Pop the cover that operates the cord return you will find two phillips head screws under it; take them out and the covers comes right off. ... Vacuums
How do i open the motor housing for my electrolux e2000 vacuum
... Electrolux UltraLux 2000 Bagged Canister Vacuum
I want to open the motor of vassum cleaner ....how
Let me know what kind of vacuum it is and the model # and ill walk you through it ... Vacuums
I have a Electrolux cannister Type Epic 6500 SR vacuum cleaner. The motor is making a whining noise on shutdown. What is the trick to opening it to get to the motor? THANKS, John
Hi there,the best thing you can do, is to disassemble the casing of the unit, ... Electrolux Vacuums
I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?
Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums
I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together
My Electrolux Regency Series upright vacuum brush motor does not activate. Cleaned the brush and press reset to no avail. Opened handle switch assembly and checked each wire attached to all three switch settings. Tried disassembling brush assembly but could not pry open after removing all screws.
... Electrolux Vacuums
Windtunnel Hello: I was reading thru another readers problem of power to vacuum but won't turn on. Same problem for me. All hoses are free of clogs and I have the vacuum basically taken apart as far as I can. You state a THERMO by the motor may be open. What does this part look like? Thank you. Craig
The thermo is a small square piece with two wires coming out of it. Did you check the switch? The switch has a high failure rate. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
My vacuum cleaner stopped working without any smell or anything. I took to a local repair person and he said nothing wrong except motor he tried new hose, etc. And he wants to change the motor..
I would go with the repair man and what he says. They know what they are talking about and if he was trying to rip you off he would have suggested many things to repair and then after you had spent a few hundred he would have told you to replace the ... Kenmore 25512/ 25513 Progressive Canister Vacuum
I have a Z345 Electrolux cylinder vacuum cleaner, from the 1970s probably, but not used much. I have lost the guide. I forgot to change the bag before it was full. Smoke started to come out - smelling of burnt paper, not rubber. So switched off. It did not blow the fuse, and may be OK. I wish to inspect it. How do I open it up? Alos I have an air filter and a motor filter for it. I have often changed the air filter on the top. How do I get at the motor filter, if there is one? Than
Good day! OK you have to is replaced the bag and that's it.And don't forget to change the bag again to avoid that problem.Thank you ... Electrolux Guardian Bagged Canister Vacuum
The roller brush on my Hoover Z700 vacuum no longer runs when you tilt the handle back. I have tested every part that I can: the motor is good; the "magnetic switch" at the pivot point is good; etc. I'm now stumped. Any help or suggestions would be greatly appreciated as I don't want to throw away a $400 vacuum.
Has this not got a rubber belt drive? ... Vacuums
Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.
... Sanyo Vacuums
Removing kenmore vacuum Canister motor cover model 116-27312790
What you need to do is take it apart and look for any carpet peices dug up in there preventing the motor to spin. Also go look for another filter for it and if you google it you can probably get instructions or if you still have the book. ... Kenmore 25512/ 25513 Progressive Canister Vacuum
It's an old cannister electrolux vacuum cleaner and it's not worth to have it serviced. The motor is noisy it appears to be obstructed but I can't open it since I don't see any screws. Would you please tell me how to do it. Thanks Ray
You will need to peel the soft rubber bumpers away from the side, like pealing a banana. Grip the bumper tabs with needle nose pliers from the bag area with door open. Underneath will be a set of locking keys which slide forward ONLY out the front o ... Electrolux Guardian Bagged Canister Vacuum
Need manual for Eureka Powerline Plus Model 9730 Type A - missing "door" that covers tool access port on body of upright motor...any ideas? This causes dirt to fly out unless tool hose is placed in "port"--don't always want to use tools, just main vacuum.
I found it at www.vacpartswarehouse.com for $4.79 + sh ... Eureka Powerline LiteSpeed 5845 Upright Vacuum
Hello, we have a Miele cat and dog turbo 5000 vacuum cleaner which we bought in December. It has just started blowing air out of the grid on the top of the cleaner instead of sucking from the tube. The whole top section which is opened to change the bags doesn't seem to want to clip down properly either. Do you have any ideas> I'm gutted as it was so good until this happened. Thanks Michelle.
The lid not closing properly is almost certainly the cause of your problem. Without that lid sealed tight to the body you will get no suction through the hose. So, the question is: why isn't the lid clipping down properly? Did you just change the bag ... Vacuums