Having problems with your Vacuums ?

Aeg viva spin not working - Vacuums

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Aeg viva spin not working - Vacuums

... Vacuums

My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?

Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums


This unit uses a turbine assy to turn the brushes. The brushes could have something jamming them. Remove the brush unit, it is held on 2 spring hooks 1 on each side. The brush unit is driven thru a 1/4" square post, only one brush is driven and it dr ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My Rainbow SE vacuum was working fine until I ran over the edge of a rug and it went in to the nozzle. I immediately switched the vacuum off and proceeded to move the rug. When I tried to turn the Rainbow back on the brush was no longer spinning. I've tried the reset button and checking the nozzle for any debris, there are none. The brush just won't spin.

Hello lilbutmunch1,\015\012The brush is motor/belt driven so you probably either broke the belt or it shifted off the motor or brush shaft. I suggest you unplug it,flip it over and look for screws that hold the baseplate together.. remove those ... Rainbow E series Canister Wet/Dry Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag

... Euro-Pro EP621 Bagless Upright Vacuum

I have a Dyson Ball vacuum cleaner and slowly the spinning portion of the vacuum ceased to work. We checked for hair, etc. that might be caught but it is all clean. We also checked the filter within the ball portion of the vacuum. Any suggestions would be great!

Hi Antonia. I assume the spinning part is the brush roller. If so, you have a broken or stretched belt. I am not too familiar with the Dyson. I would be interested to know your progress so I can learn also. Thanks Chris ... Dyson Ball DC24 Bagless Upright Vacuum

My Eureka Maxima isn't working right. The belt is spinning fine until I lower the handle to start to vacuum and then the belt stops spinning. As soon as I put the handle back in the upright position the belt spins again.

Sounds like belt is worn try changing belt. ... Eureka 4700A Maxima Bagless Upright Vacuum

My DC07 Animal Bagless Upright Cyclonic Vacuum has a small attachment for vacuuming carpeted stairs. This attachment is currently not spinning its internal brush necessary to pickup the dirt on the stairs. The rest of the vaccum is working fine. The suction cap on this attachment is pulled out, as it should be. I have checked the vacuum over thoroguhly and there are no bloackages anywhere.

Make sure to extend the wand straight up and completely out of the handle and watch that you don't kink the hose. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The vacuum works well. The brush does not spin

Hi its Darran at Dyson. If you have a brush control, make sure that its in the centre position when its stood upright and then try releasing the head to put the machine into the vacuuming position and see if the brush control dial moves f ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Luv300b vacuum brushes won't spin. The belt is fine but still not working. Any suggestions?

... LG Electronics Kompressor Plus Upright Vacuum Cleaner LUV300B

Roomba Discovery My Roomba Discovery seems to work fine, mechanically, but it no longer seems to collect any dust. (The collection bin remains empty after the Roomba has circulated around the floor for quite a while). The brush has been replaced and spins normally. Does anyone have an idea why this machine's vacuum function no longer seems to work? I would appreciate any feedback. Jeremy

Did you replace the filter? when you remove the dust bin there is a small filter that needs to be cleaned, or replaced. You can buy a maintenance kit that replaces the brushes and filters as well, its good to replace them all regularly ... Roomba Robotic Floor Bagless Vacuum

I was vacuuming over some fringe and then the brush just stopped working and there is nothing caught in it. It spins freely when twisted by hand, but will not turn when vacuum turned on.

Have you checked the belt? it could have snapped when you caught the fringe. also if it has a separate brushroll motor there should be a reset that probably tripped out. ... Vacuums

Hepa filter does not turn on hoover wind tunnel vacuum model U6630900. It was working (turning) and I cleaned the filter and canister and now it no longer spins when the vacuum is running.

The part you refer to is not the HEPA filter. It's a very common misconception that that part spins - it looks like it when there's dust whirling around it. In fact, it does not spin - there are no visible moving parts. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Eureka The Boss Mini (Model # 442) vacuum cleaner. It is not working properly sometimes Today I did a cleaned the roller brush thoroughly and powered it on to see if it spins at all. It spins only in Carpet model, but stops sometimes. Please can you tell me what could be the problem?

... Electrolux Vacuums

My vacuum cleaner spins but has no suction when I go to vacuum- only hose with accessories works

Check for a clog between the hose and the front opening. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.

You need a new belt. ... Vacuums

I have a Bissell pet hair eraser model #3920. It's been working great until last night. I went to use it and the brush won't spin. It also smells like it's burning. I checked the belt and it looks fine, and the brush spins by hand easily. It's not clogged anywhere that I can see. Anyone have any other ideas? This vacuum is only 8 months old.

- Remove the access panel, which is on the bottom of the machine. There are 4 tabs to lift on the access panel to remove. Start with tab 1 then 2-4 tabs.- Check the brush, and belt for any damage. Clean off any debris on the brush. ... Bissell 3920 Bagless Upright Vacuum

How to repair BEAM Central Vacuum Power Brush. Motor works perfectly, belt brand new but unable to spin brush.

... Vacuums

I was vacuuming with the Dyson DC 17 and sucked up a berber carpet string by accident and after cutting and pulling it all out of the bottom brush part, the brush no longer spins but the suction part works. What do I do?

The belt could be snapped. If this model has a brush protected belt then it has to be repaired by a service call. If however you can get to the brush roll belt by removing the bottom sole plate (turning over the vacuum so that you're looking at the b ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My carpet cleaning brush does not turn on. The vacuum cleaner works fine but the the carpet cleaning attachment does not get any power so the light does not come on & the brush does not spin

... Kenmore 25512/ 25513 Progressive Canister Vacuum

My eureka optima vacuum shuts off after 5 minutes of use, the brush still spins, but no suction. If I wait 30 minutes, it will work again, for 5 minutes.

... Eureka 431A Optima Bagless Upright Vacuum

Dyson animal dc14 - beater spins but vacuum not working - not clogged - is there a reset or is it something else?

Hi there, if the machine is not blockage (which is the most likely cause) its possible that the internal hose has twisted, lifting the cleanerhead off of the floor slightly. To recitfy this, lie the machine on its side and you should be able to see ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a hoover upright vacuum 1 year old and the brushes wont spin but the attachments will still work

Change the belts and if it still doesnt work theres a problem with the motor ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum

I have a hoover windtunnel upright vacuum bought it a few months ago and now the brush spinning stopped working.

You probably have a broken belt, or the belt came off. The Self Propel Windtunnel has an issue with the pulley that tightens the V-belt in place getting stuck and needs to be taken apart and released, but most l ... Hoover Vacuums

The brushes on the Hoover F7452-900 SteamVac Upright Vacuum will not spin but everything else seems to work fine. How can I solve this problem?

There is no belt. This unit uses a turbine that uses air off the vacuum motor. There is an actuator arm that moves rearward when you depress the handle release and then lower the handle to use the vacuum. That engages the turbine and spins the brushe ... Hoover F7452-900 SteamVac Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1081 seconds