Having problems with your Vacuums ?

Roller brush removal kirby g upright

\015 How do I remove the brush bar after I remove cover plate, it seems stuck\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Roller brush removal kirby g upright


GO HERE > http://www.youtube.com/watch?v=At7tqnjD-Kc ... Vacuums

How to remove brush roller ultimate g - Kirby Ultimate G Bagged Upright Vacuum


Http://www.youtube.com/watch?v=At7tqnjD-Kc ... Kirby Ultimate G Bagged Upright Vacuum

I have a eureka bravo upright model 9600. I have removed the hood . I need to remove the brushe roller to install a new belt. I cannot figure out how to remove the brush roller.


Check out this URL:\015\012\015\012http://www.svcvacuum.com/beltrep2.html\015\012\015\012looks like it has just what you are looking for.\015\012Would appreciate a thumbs up on this if you find it beneficial.\015\012Paul ... Eureka Vacuums

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

How do you remove brush roller from kirby legend 11 shampooer


... Kirby Vacuums

I am replacing drive belt on Eureka 4870 upright. Before installing I removed bottomplate and was cleaning out accumulated lint, hair and grit. Found a pair of identical (reciprocal) felt gaskets sucurely inserted above and below the roller brush, and one small loose piece of felt approximately 1/3 inch wide by 1 inch long that came out as I was pulling out debris. It has a slight crease across the middle as though I was not resting on an entire flat surface, but I find no other clues as to wher


If you go to this URL:\015\012\015\012http://www.VacPartsWarehouse.com/Eureka-4870-Ultra-Smart-Vac-s/1928.htm\015\012\015\012in the exploded view of the unit, identifying the parts and look at item 18, I believe it is where your felt part ... Vacuums

Can't remove Kirby roller brush


This video will give you full instructions ... Vacuums

Should the roller brush on the kirby always be spinning?? just inherited a kirby 5, and the roller brush is not turning when the vacume is on. ??


Yes it should alway be spinning when you switch on the machine, if it's not spinning i would sujest the belt as come off or broke this video will show and explane what you need to do to replace or put back on . ... Vacuums

Hi, I have not owned my electrolux pronto 2 in 1 for very long but the roller brush has stopped turning. The handheld part works and the green light is on. I have done a thorough cleaning of the roller brush and all other removable parts. What might be causing the roller brush to not work? Thanks, Jen


Check the end cap bearings ... and replace the belt even though it may not be broken. Put a drop of sewing machine oil (no more) in each end cap bearing. ... Electrolux EL1000A2 Pronto Bagless Stick Cyclonic Vacuum

Upright dirtdevil roller jammed - how to remove square endcaps for cleaning


The brush roller is secured with elastic stop nuts. Clamp the nut at one end with a wrench or pliers and remove the nut from the opposite end. This will allow the shaft to be removed completely for cleaning ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?


The same thing happened to me about a year ago with this very model. \015\012The issue on mine was a small, copper-colored metal wheel that attaches to the end of the brush roller. You'll need to remove the top cover (there are several screws). ... Eureka Smartvac 4870 Bagged Upright Vacuum

Riccar model rad.7 upright (radiance). roller brush won't turn and red roller brush indicator is on. roller will turn easily by hand and belt is in place. how do i fix this?


As you already know, the red brush indicator light indicates that the brush roll has stopped turning, usually because an object has become stuck in the brush roll. When that happens you should turn the machine off (unplug it also for safety), remove ... Riccar 8955 Upright Vacuum

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems


Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,


It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

Riccar upright vacuum roller brush replacement


... Riccar 8955 Upright Vacuum

Roller brush on Dyson D25 not working. Have removed roller brush and cleaned it as per instruction booklet advise. But to no avail.


... Dyson DC25 All Floors Bagless Upright Vacuum

Kirby sentria My roller brush won't spin belt is not broken I cleaned the Roller brush and put it back it. It put it back but it looks like the sensor balls aren't touching the plastic part underneath. The green light Doesn't turn on either. It was just working and it stop picking up out of nowhere this


... Vacuums

I got a cord wrapped around the roller brush and after removing it the roller brush won't turn.


Should have smelt a rubber smell at the same time. The rubber belt probably melted in half. Just flip vacuum over so you can see the bottom. look for arrows pointing to clips or screws. Usually requires removing one panel and the brush. Buy new belt ... Electrolux 5740 Upright Vacuum

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?


Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

How can I change the belt on the kirby vacuum shampooer brush roller. There is no way to snap the roller out and it seems that trying to unscrew the end isn't doing anything either.Model 5584 renovation group is what is written on the shampooer attachment. The kirby is a heritage model 2HD - purchased in the late 1980's.


... Kirby G6 Bagged Upright Vacuum

I have a model # 880 Royal upright that the brush roller ends are bad. Can I get replacements for these? They have the 1/2 in. square ends. What about replacement for the whole roller assembly. The brushes are fairly well worn. Thanks, Arthur Summers


The below site sells the rollers for some models. I'm not sure about yours. The second one, part number R-673273, may fit. Check your brush for a part number. \015\012\015\012 ... Royal Vacuums

I removed the brush from bottom of the vacuum to remove hair from the bristles. When I re-assembled the vacuum, there was no longer suction. Also, the vacuum no longer stands upright when not in use. It's like something is blocking the upright portion from locking.


... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a DC14 with a bad belt to the roller.How do I remove the clutch that operates the belt to turn the roller. I am holding the assembly that houses the clutch and all screws are out, it appears the red knob that engages the drive to operate the roller brush must be removed. Please advise and how. Thanks, John.......[email protected]


You need a special tool to remove the clutch. Contact the Dyson Helpline so that they can refer you to an authorized Dyson dealer in your area who would have such a tool and who can fix it for you. The alternative is to purchase a tool and visit YouT ... Dyson DC14 Bagless Upright Cyclonic Vacuum

I unscrewed the roller brush protective cover and removed the brush to clean it. Now the roller won't turn because the drive shaft is not turning. Is there a reset button or something?


I looked at the pictorial of this vacuum at this URL:\015\012http://middleeasten.bissell.com/images/UserGuides/3750.pdf\015\012\015\012This shows the belt to slide on the motor drive pulley and also on the brush. If the brush is bound up on th ... Bissell 3750 Lift Off Bagless Upright Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0604 seconds