Having problems with your Vacuums ?
How do I replace the belt on my everstar vacuum model vc-9550?
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
How do I replace the belt on my everstar vacuum model vc-9550?
Where is the belt located for everstar vacuum cleaner model vc9550 so i can replace it
I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.
The Panasonic MC-V7515 has two belts. The local vacuum repair guy says he only has a part number for the drive belt, which is UB-9. How do I find a replacement for the other belt, the one which directly drives the beater bars? By the way, this vacuum has great suction, but otherwise is far inferior to my previous Panasonic vacuums. The cheaper models aren't a good buy--stick with the more expensive models.
... Panasonic MC-V7515 Bagged Upright Vacuum
Belts I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do t
It is the flat belt that gets stretched and should be replaced at least every 6 months. The V belt wears down so it won't it right in the brush roll V. Maybe the belt tensioner wheel has a problem, sometimes they get hook up and won't engage the V ... Vacuums
My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?
Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do they re
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=675093\015\012Generic problem for all Vacuums\015\012I have a Hoover self-propelled\015\012Posted by kl ... Vacuums
I have a Fantom Fury and need to replace the belt. Please tell me how to get into it so the belt can be replaced. It is a Fantom Fury Vacuum Cleaner # 3680093 Fantom Technologies Model # F10051 01
How to replace the belt on my bissell model 3512-9 vacuum
Tehre are tabs on the bottom. Push them in the direction of the arrow (one at a time) and lift with some force on the cage thingy that partially covers the sweeper. Do the same for the other side. It doesn't matter which side you do first. ... Vacuums
My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc
... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
Belt replacement Does Hoover Windtunnel V2 model # U8148-900 even take a belt? The owner's manual only describes how to change belt in powered hand tool, not the vacuum itself.
No belt- it is motor driven. what happens to these if the rollers get stuck(by- say, a Lego® or something) is the roller itself has an insert which will break, requiring roller replacement. \015\012\015\012simple fix, but costs a ... Hoover WindTunnel V2 U8148-900 Upright Vacuum
I replaced the belt on my model 3920 because the vacuum was very noisy. It is still making the noise. It is so loud that I am concerned that there is some other problem with the vacuum. Any suggestions?
Sounds like an obstruction in the blower motor fan or bad bearings in the blower motor located in the bottom end of the main body ... Bissell 3920 Bagless Upright Vacuum
Replace belt on model 116.5017080 vacuum - Kenmore Vacuums
... Kenmore Vacuums
LOUD noise Turned on vacuum one day and it made a reallly loud noise like the belt had broken. So we replaced the belt correctly, and turned it on and the noise is still there it is also rattling violently. HELP PLEASE not exact same model but close enough
The armiter or fan is broken and if you get it replased it should work like new ... Hoover U5227-930 Elite Upright Vacuum
Lost manual on vacum need to replace belt - Eureka Altima Upright Vacuum Model 2996AVS Vacuum
Remove the bottom cover of the sweeper head, then remove the brush roller along with the belt if still there. Clean the brush end-bearings--the roller ends and the interior of the bushings. Then oil the bearings lightly with 3-1 oil or similar. Place ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
Looking for new belt for my electrolux guardian canister vacuum power nozzle marked model n106m . have been unasble to locate an appropriate belt replacement. Any suggestions?
This company is now known as Aerus. If you can't find their listing in the local yellow pages, follow the instructions on the folloing site.\015\012\015\012 ... Electrolux Guardian Bagged Canister Vacuum
Need to replace belt on a Kenmore Model: 116 37312690 vacuum. Have taken torn belt off. Is there a diagram available? I have lost owner's manual.
Instructions:\015\012\015\012\015\012 ... Vacuums
Can't find a site to order a replacement belt for my Shark model V15Z which I bought for our motor home. It was used very little before the belt broke. I will be trashing this vacuum, and will NEVER buy another Shark product.
This web site has the belt for V15Z http://www.appliancefactoryparts.com/vacuumcleaners/brands/shark/v15z.html I found this one works great Pain to get belt on but not a problem since then. http://www.totalvac.com/ROR-1040.html (Dirt Devil type 1 Bel ... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray
I need to replace belt #38528-033 on a Hoover WindTunnel vacuum model #U5463-960. I've had the vacuum for a long time and have misplaced all operational and instructional info that came with it. Any help would be appreciated. Thank you.
Replace the belt on a hoover washing machine ... Vacuums
Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus
... Bissell 6595 Lift Off Bagless Upright Vacuum
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum
How to replace brush belt on vacuum cleaner Ryno model
Need to replace belt on my Kenmore Progressive Vacuum Model # 116
HiOn your products manual is the replacement procedure.www.managemylife.com/mmh/lis_pdf/OWNM/L0311026.pdf ... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum
Eureka vacuum belt how do i replace on model #4688
How To Replace Brush Roll BeltNOTE: Turn off the switch and unplug the electrical cordbefore replacing belt. Belt pulleys can becomehot during normal use. To prevent injury, avoidtouching the motor shaft when checking the belt ... Vacuums
How do I replace the belt on my eurika vacuum it is a boss model.
Did you say that you have a Eureka? Also you need to know the model number because belt changing methods and belt sizes vary depending on the model. You can find the model number on the vacuum and can find the belt you need in the manual. Then you ca ... Emerson Vacuums