Having problems with your Vacuums ?

Need Beater Assembly for a Taylor 380-12 (part # X50525).

\015 I need a beater assembly for a Taylor 380-12 (part # X50525). If you have one avlb pls call 847.550.6274. \012\012Thanks...Rick\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need Beater Assembly for a Taylor 380-12 (part # X50525).

... Vacuums

I need a service manual for an Electrolux C104A vaccuum. I know the part I need but don't have a part number. The part description is the hose connector at the beater attachment.

If you talking about the part that swivels it is called the elbow and the part number is 46861. ... Electrolux Guardian Bagged Canister Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?

Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I need a Dyson DC 17 Total Clean exploded parts diagream that shows the switch assembly. There are two small springs and a small plastic part that were loose inside the switch assembly. This caused the vacuum to shut off in the full upright position which is the position you use when using the wand.

I don't have a full diagram for you, but I do have a photo of how they are meant to be assembled: ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Pls Help! My Dyson DC05 (Yellow) needs a new wand. Am unsure whether it is the assembly wand or hand one found in spare parts. The wand I need to replace connects the two long hoses together, and NOT the wand which fits onto pickup head. M.thks if you can advise which one I need. Getty rather dusty in my pad!!

... Dyson DC05 Bagless Canister Cyclonic Vacuum

Hi, I have a Kenmore Whispertone canister vacuum that I purchased in 2007. The model # is 116.22271503C, which seems to confuse the parts people. I need to buy a new powerhead & a few months ago was given a price of $75, but now Sears Canada tells me the part # is 20 116KC5OXBZRZUO1 described as Power Mate Assembly for $192.99. I thought the Power Mate was the small powerhead for stairs, upholstery, etc. Have they located the wrong part for me, or is this really what it costs?? Thanks in advance

Yes, powerheads are quite expensive. That sounds about right.\015\012You can check Ebay for better prices, but check the shipping rates before ordering. ... Kenmore Whispertone 23312 Bagged Canister Vacuum

Hoover Steam Vac Dual Tank Bottom Valve Spring Assembly Part Needed

It appears that there is a problem with the o-ring design. The o-ring should maintain a certain OD dimension and keep the spring assembly from pulling throught the hole. I am trying to find the service manual to locate the o-ring part number but hav ... Hoover F7431-900 SteamVac Vacuum

I need to replace the cord on the beater brush attachement for s3614 hoover powermax.. can't find parts. I was able to pull apart the brusher, but I cannot release the wire to resplice and reconne

... Hoover S3614 Vacuum

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi

Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

My mother purchased a replacement hose assembly for a Bissell ProHeat 2X and the part was shipped without any instructions... While I am pretty handy, my issue is with the supply tube, and I cant figure out how to accomplish the replacement, and as its not MY vacuum, Im hesitant to start taking things apart.I just need instructions to replace the entire hose assembly.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is

... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I need to change the motor in a vax 6131 but i don't know how to get into it to get the change it? I also need to get into the motor assembly housing to change a part but can't see how it comes apart!!

On the handle there is one small pozidrive screw, remove and orange panel comes away revealing powercable securing bar. Remove 2 screws and this reveals a 10mm headed bolt. Under label on top of handle there is another small pozzi screw, undo t ... Vacuums

I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile

... Eureka Smartvac 4870 Bagged Upright Vacuum

Parts diagram I have taken the assembly apart and I would like to see a diagram in order to know the part numbers that i need to order for repair.

You may like to try here see if yours is listed http://onlinevacuumparts.com/s-3-bissell-vacuum-parts.aspxriz. ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Took apart my cleaning brushes and all on my bissell spotbot i need diagram of how to fit the head part back to the machine. I had a problem with the auto not working i have fixed that problem just need to see so that i can get it back togoether. I assembled the whole wheel back but cannot caonnect it to the machine LOL

... Bissell 1200A SpotBot Pet Robotic Vacuum

The Neutral/drive pedal fell off our Kirby G5 vacuum cleaner. I opened up the area housing its connection to the transmission and a couple of the parts were just laying inside. I need a diagram for assembling it and see if I am missing any parts. It was a refurbished machine and a paperclip fell out of the housing when I opened it. Can you help me?

Hi,In the below links you have the parts diagram as you asked will this helps you?If not let me know i will help you more.http://www.fiorijanitorial.com/s-19-kirby-parts-and-bags-generation-3456.aspxhttp://www.vacu ... Kirby G5 Bagged Upright Vacuum

Need part for electrolux beater bar rug cleaner.

... Vacuums

I need assembly instructions for a GardenLine hose reel trolley as the instructions that came with it are so vague and do not tell you where all the parts go.

Check for GardenLine parts here Gardenline Einhell Genuine Spares and Accessories Buy Online ... Vacuums

I need part number of front wheel assembly...

Part number for the wheels [you'll need to order two] 74818a-119n, the axle is part no. 71478 - available at sears 1-800-4myhome ... Eureka 4700A Maxima Bagless Upright Vacuum

Need assembly part diagram - Dyson DC07 Bagless Upright Cyclonic Vacuum

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Need parts diagram of holley 0-80559 4150 marine carburetor

... Holley 0-80559 Carburetor 600 CFM Marine

Where can I get a parts list for the miele s514? I need to replace the power cord assembly.

... Miele Vacuums

How do I get a replacement belt for my DC 17? We sucked something up and broke is so I do not care if it costs anything, I just need a belt for the beater. How do I get one? unfortunately my wife also through out the old one with a part number on it,....

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I need a vacuum brush housing assembly for Dyson DC15 animal. Part of it is broken (plastic).

Http://www.espares.co.uk/dyson/dc15/p/1086/716/10\015\012\015\012Try the above link or do a search in google for "Dyson DC15 parts".\015\012Also, tr ... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

Where can I find a part for my BV2000 in house vac? It is the smallest unit made by M S & S Systems in Dallas TX. The suction impeller is grinding in it's housing, so I need a motor/suction pump. I have removed this combination from inside the vac assembly

You will have to replace the whole motor as these motors where never made to be serviceable. if you take the motor to a local vacuum shop than can order you a new one. though i would recomend replacing the whole tank unit with a Nutone or Hayden they ... M&S Systems BV-2000 Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0863 seconds