Having problems with your Vacuums ?

Replace the roller on my kirby vacumm generation 3


Answers :

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=814340
\015\012Generic problem for all Vacuums
\015\012Replace the roller on my
\015\012Posted by tlourene on Jul 21, 2008
\015\012Replace the roller on my Kirby Vacuum Generation 3
\015\012Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. In order to replace the brushroll on the Kirby G3 you need to dial off the belt and then release the lever to remove the bell housing, then there are 2 levers that you need to open then you can get @ the brushroll --- take out the brushroll and replace the brushroll and a new belt – make sure you change the belt every 4 to 6 months for the best cleaning. Make sure when you put the new belt in the housing that the screw heads are facing down – then you can replace the bottom plate, dial the belt on to the belt pulley and replace the bell housing. If you need further help please refer to a local vacuum cleaner dealer in your area. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

\015\012http://kirby.com/
\015\012Customer Service – U. S. & Canada
\015\0121-800-494-8586
\015\012Hours 8:00 am to 5:00 pm (EST)
\015\012Mail To: Consumer Relations
\015\012The Kirby Company
\015\0121920 West 114 Street
\015\012Cleveland, OH 44102
\015\012Thanks, Don the Vac Man
Go Ahead. Use Us.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replace the roller on my kirby vacumm generation 3


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=814340\015\012Generic problem for all Vacuums\015\012Replace the roller on my\015\012Posted by tlourene ... Vacuums

How do I replace the belt on kirby generation 3?


The instruction is HERE with plenty of pictures.Good luck ... Kirby Generation 3 Bagged Upright Vacuum

Kirby Hello, I have a generation 3 kirby- it was working - I turned it off & it will not turn on again - is there a safety switch /reset button or did the on/off switch go out - I have had it 15 years & replaced the switch 1 time - Thanks


You either need a switch or a cord. Check out my troubleshooting link which includes links to do-it-yourself guides and parts.\015\012\015\012 ... Kirby Generation 3 Bagged Upright Vacuum

How to replace kirby generation 3 switch? - Kirby Vacuums


I am a trained professional with all the tools & experience and this is a job that would take me 2 hrs. Do your self a favor and take it to your local vacuum shop.It'll probably run you around 200 dollars , half parts and half labor. You pr ... Kirby Vacuums

Kirby g6- How do you replace the cord? - Kirby Generation 3 Bagged Upright Vacuum


I do believe o6 the cord goes in to the metal housing of the motor .They are usually held in by a rubber grommet and they can with some patience and force be pulled out slowly does it as you don't want the wires ... Kirby Generation 3 Bagged Upright Vacuum

Replacing brush roller on my KIrby g6 limited edition


You need a new belt. When the green light goes out, that means your brushroll has stopped spinning. Here's how to change it....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

Cant get the suction impellar off to replace - Kirby Generation 3 Bagged Upright Vacuum


Shaft has to be spun clockwise. It has reversed thread. If this is not the problem but you just need to somehow hold the field - see instructions HERE. You may ... Kirby Generation 3 Bagged Upright Vacuum

How do you attach the belt for the roller-brush on a Kirby Generation 3, up-right vacuum-cleaner?


Greetings,\015\012\015\012Please see the attached video on how to replace the belt on a Kirby Generation Vacuum Cleaner. This is an easy to follow step by step direction on the proper way to replace the belt, as well as do basic mainten ... Kirby Generation 3 Bagged Upright Vacuum

Replace fan blade e77491 - Kirby Generation 3 Bagged Upright Vacuum


KIRBY VACUUM REPAIR HOW TO REPLACE THE FAN IMPELLER ... Kirby Generation 3 Bagged Upright Vacuum

Trying to replace the belt on my Kirby. I have the plate off but I cannot get the roller brush out..husband and I both tried.


Turn it up where you can see the roller push it in and slide it to the back are the frunt it should come out ... Vacuums

I broke my kirby generation 3 vacuum cloth bag latch i found where to get the part but how do take it apart to replace it


... Kirby Generation 3 Bagged Upright Vacuum

How do i replace a kirby vacumme bag?


If you look on the back where the bag goes in the vacuum you will see a strap at the end of the bag, loosen the strap and remove the bag ... Kirby G6 Bagged Upright Vacuum

The bag latch on my Kirby Generation 3 broke. How do I get the old one off to replace it


At the bottom of the bag, there is a zip tie around the plastic part that turns & snaps on to the exhaust hole of the vac. also take a flat screwdriver & pull up the rubber under the zip tie...all the way around, like u would take a bike tir ... Kirby Generation 3 Bagged Upright Vacuum

Not sucking i have a KIRBY G3 that was working great. One day there was a strong smell and the brush roller belt broke so I replaced it. The fan looks good. Now the vacuum does not **** up dirt but instead seems to very gently blow air forward. I took the (new) bag off and it is blowing hard int the bag. I am stumped!


Belt is not connect to the drive pulley, see manual for fitting or see utube for video ... Kirby Generation 3 Bagged Upright Vacuum

Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus


... Bissell 6595 Lift Off Bagless Upright Vacuum

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,


You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

Replace release button on kirby 3


I assume you are talking about the release on the handle pivot. Unhook the bag so it is out of the way, take the hanle off, take the top cover off, then there 2 screws holding the handle oivot asm, take them out, replace witht he new one, making sur ... Kirby Ultimate G Bagged Upright Vacuum

SEBO Sensors Where are the SEBO X4 sensors, I have taken this apart and not too sure where the sensors are. In particular I get Replace Roller coming up, but roller seems fine and it goes round ok if I disconnect the PCB. My unit turns on spins for 10 seconds and then brings on light C. Just replaced the motor on it about 4 months ago so not too keen to get a new one. Any help welcome.


... Sebo X4 Bagged Upright Vacuum

How can I change the belt on the kirby vacuum shampooer brush roller. There is no way to snap the roller out and it seems that trying to unscrew the end isn't doing anything either.Model 5584 renovation group is what is written on the shampooer attachment. The kirby is a heritage model 2HD - purchased in the late 1980's.


... Kirby G6 Bagged Upright Vacuum

I have a model # 880 Royal upright that the brush roller ends are bad. Can I get replacements for these? They have the 1/2 in. square ends. What about replacement for the whole roller assembly. The brushes are fairly well worn. Thanks, Arthur Summers


The below site sells the rollers for some models. I'm not sure about yours. The second one, part number R-673273, may fit. Check your brush for a part number. \015\012\015\012 ... Royal Vacuums

The roller is not spinning. I took the bottom screws off but and replaced the belt but am not sure how to replace the clutch. I think that is what it is anyways, the thin silver bar that controls if the roller is spinning or not


... Riccar 8850 Vacuum

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel


The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

I have a GE 106766 Canister Vacuum. The belt on the power end stretched and I replaced it. Now the roller froze up and won't move. Where can I find a replacement roller?


Try this sitehttp://www.onlinevacuumparts.com/ps-328-7-ge-6850-106766-canister-power-nozzle-parts.aspx ... GE 106766 Bagged Canister Vacuum

Kirby Generation 3 Pictorial or wiring diagram


Go HERE. This should be more than enough info.Rocky ... Kirby Generation 3 Bagged Upright Vacuum

Should the roller brush on the kirby always be spinning?? just inherited a kirby 5, and the roller brush is not turning when the vacume is on. ??


Yes it should alway be spinning when you switch on the machine, if it's not spinning i would sujest the belt as come off or broke this video will show and explane what you need to do to replace or put back on . ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0501 seconds