Having problems with your Vacuums ?

My electrolux epic 6500sr vacuum has a seized motor. How do I acess the motor to service or change it? There are no obvious screws or clips to open the motor outer case

\015 I have tried to pry the housing open,but fear I may break it if I put too much pressure. Please Help. Thanks Roger\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My electrolux epic 6500sr vacuum has a seized motor. How do I acess the motor to service or change it? There are no obvious screws or clips to open the motor outer case


... Vacuums

Miele S5000 (revolution 5000) vacuum cleaner - How do I open the casing? When the power button on the handle is pressed the green power-level lights on the handle light, but the motor sounds like it gives a little 'jump' but nothing more. The orange power light on the body also dims. I assume the motor or fan is jammed, but I can't open the body to find out. I've taken out to screws inside near either end of the handle, but to no apparent effect. I'm assuming the body is held together by plastic


... Vacuums

It's an old cannister electrolux vacuum cleaner and it's not worth to have it serviced. The motor is noisy it appears to be obstructed but I can't open it since I don't see any screws. Would you please tell me how to do it. Thanks Ray


You will need to peel the soft rubber bumpers away from the side, like pealing a banana. Grip the bumper tabs with needle nose pliers from the bag area with door open. Underneath will be a set of locking keys which slide forward ONLY out the front o ... Electrolux Guardian Bagged Canister Vacuum

How do i open a sanyo sc-b555 to get to the motor. i need to remove the casing but i can not find all the screws?


... Sanyo Vacuums

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb


Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

I am trying to open the outer casing of the vacuum


There is a push in type flat plastic switch trim cover over the metal housing surrounding the switch.. You must unplug the cord, gently pry around the trim cover and you will find a screw, an irregular one underneath holding the switch in place. DO ... Vacuums

How to open the motor housing.


Pls i want put music in my phone but its not possible i need ur help ... VAX Appliances 2000 Canister Vacuum

My Ergospace Vacuum took some apple juice in and now it makes strange noice and even threw out some sparks. Is there anything I can do my self or is it over with this vacuum cleaner? I opened 6 screws, but I still can't open the motor cover. Are there some hidden screws?


Liquid plus electrical parts always ends up with the electrical parts losing. Juices, although they will dry, will leave behind a sticky residue. You'll need to replace at least the motor, but due to the other electrical components, probably be bet ... Electrolux EL4100A Ergospace Cannister Vacuum

I have a Z345 Electrolux cylinder vacuum cleaner, from the 1970s probably, but not used much. I have lost the guide. I forgot to change the bag before it was full. Smoke started to come out - smelling of burnt paper, not rubber. So switched off. It did not blow the fuse, and may be OK. I wish to inspect it. How do I open it up? Alos I have an air filter and a motor filter for it. I have often changed the air filter on the top. How do I get at the motor filter, if there is one? Than


Good day! OK you have to is replaced the bag and that's it.And don't forget to change the bag again to avoid that problem.Thank you ... Electrolux Guardian Bagged Canister Vacuum

Motor problem I just picked up a screw. It appears to be stuck in motor. The sound of the motor changed to a whirring noise and it started to smoke. How can i access the motor?


First six pictures HERE will let you know how to remove shell to see the motor. I would not recommend starting it before you get the screw out (you will need to ... Kirby Generation 3 Bagged Upright Vacuum

Miele Cat & Dog vacuum gets VERY hot and is VERY loud. Hose has no restrictions and I have changed the dust compartment (motor) filter and the exhaust filter. It still gets hot when I run it with the top open and all filters removed, so I'm guessing the problem is with the motor. Should I be going into the motor compartment? If so, what am I looking for?


Hi\015\012\015\012The fact that it gets very hot could be due to a number of issues.,but the fact that it started making a very loud noise at the same time suggests that there might be more problems maybe brushes etc.\015\012\ ... Miele S514 Solaris Bagged Canister Vacuum

I have a VAX V12 vacuum cleaner which suddenly stopped. The smell indicated Carbon Brush Problems. I contacted a service agent who told me that it was not possible to change the Carbon Brushes brushes on this model and they would need to change the Motor Unit.. To me this sounds very unlikely. Two questions please. Is it possible to change the Carbon Brushes and how do I get the cabinet apart which looks very difficult. I am well qualified electrically to do this job. Regards James Beech


... Vacuums

Oreck model BB870-AS - I was vaccuming when the vac shut off. The motor just spooled down and nothing more since. I have opened the case. Have power at the switch, and to the motor, but can't get a voltage reading to the common lead at the motor. Is there a fusible link, or something similar in that lead that might have burned out? Thanks!


... Oreck Vacuums

I have an Electrolux LITE upright carpet cleaner - about 15 years old. Suddenly last night when using it, from the normal motor (whooshing) sound, the motor suddenly went very slow and with a slight grinding sound. The brushes are now just turning round very slowly and areobviously not picking up anything. Has the motor gone or is this repairable, or should I just get a new cleaner? I have tried to open the machine from the bottom to see if anything is obviously wrong, but it looks complicated a


... Electrolux Vacuums

How do I change the outer bag clip? Can't figure out how to get the top apart to put in the new clip. The clip that goes to the handle.


I had a Kirby Classic and I had to slide off the clip.Don't rate me if this doesn't work. ... Kirby Generation 3 Bagged Upright Vacuum

I am trying to change an old fashioned fuse, (house lights), luckily had a spare one. Have put the 15amp fuse wire through the whole thing, and trying to describe if I've got it right is alitle awkward, this is what i've done, cut a piece of 15amp wire a little longer than the old one, then loking at it, taken it straight through and round to left as I'm looking at it, and put the screw in, and obviously done the same for other side. My problem is that I don't remember taking the screws out of w


Hi.your descriptions are understandable and sound about right.as long as the wire is securely fixed to both pins, you should be ok.if there are any problems, especially if the fuse blows again fairly soon, then i strongly reco ... Vacuums

How to open main case on a dc08. i have removed the two screws under the top filter but i can not figure out how to seperate the main case so i can replace main switch. any help would be much appreciated


... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa


... Electrolux Vacuums

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?


Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

Our plug got pulled out (by driving away while the canister was still plugged-in after a vacuuming the car). How can we open up the unit to reattach the wires? We accessed two sets of screws (2pairs) toward the bag-end (not the motor-end) of the canister, but we can't locate any access for the two other apparent screws inside the body.


Remove all visible screws. Top and bottom, then once they are all removed, take a flat-head screwdriver and slowly pry around the canister until it comes completely loose and can be removed. Then you should have access to the wires which can then be ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Need to change the motor on dc07 how do you get the motor out I have loosened and taken out all the screws and still cant disconnect the power cable in


Have you looked at www.dysonmedic.com ?\015\012\015\012It has a really good feature on changing a DC07 motor. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Filter queen 95X (1991) Motor is noisy but still work fine. Can there be a loose screw inside ? Can I open the motor and look inside ?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=766802\015\012Generic problem for all Vacuums\015\012Filter queen 95X (1991) \015\012Posted by alexun o ... Vacuums

I am smelling a faint burning rubber smell and I think the belt needs changing, but I can't figure out how to open the case to change the belt. Can you help me?


... Hoover U5068-900 Sprint Upright Vacuum

Vorwerk VK121 vacuum cleaner - smell of burning from housing enclosing motor. How do I get into the housing to inspect the motor? After tilting the bag sideways, there are two screws holding the housing visible, but there seems to be a thrid fixing inside the point where the handle shaft is attached - is the handle simply clipped in place? Thanks


Yes the handle is clipped in place and should come out when the button in front is pushed. Remove the screws you wrote about. After that the puzzle begins. At the bottom of the vacuum where the head is attached, remove the head by pressing the but ... Vacuums

Help! i have a whispertone 300 model 116 28612790. the retractable cord is jammed & i could only get the front part of the canister open that houses the motor, etc. there are only 2 screws to open it & i can't get it off to fix the cord. hope this makes sense. thank you!


Even if you get it apart chances are it needs a new spring but it requires a special tool to get the rubber molding off that separates the top from bottom and sears repair guys and vacuum shops have them. I would take it to a used vac store and get t ... Kenmore 23313 Whispertone Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0559 seconds