Having problems with your Vacuums ?
Vax air 3 hard to push
\015 It's so hard to push when hoovering. The wheels hardly go round\015
Repair Help & Product Troubleshooting for Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Vax air 3 hard to push
The suction is good, but it can't pick up most of the stuff on the floor. The hand held hose works very well, but it doesn't even pick up little fuzzies reliably when I push it along. And, the suction is too hard I think because it used to push easily and now I have to push really hard, even on flat carpet.
Check entire length of hose, including the piece in the power head, for clogs. Simply drop a marble in one end and allow it to roll out the other. If it doesn't, then the hose is clogged somewhere. ... Dyson DCO7 Animal Bagless Upright Cyclonic Vacuum
When pushing foreward the vacuum is hard to push and if pushed on to hard it will turn over on itself.
My dyson dc17 animal had become nearly impossible to push on carpets. sure enough i found that my roller was warn down to nubs (vacuum is probably 8 years old, and gets used nearly every day) I replaced the roller and WOW! it feels ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
My Dyson DC07 has recently been service and was making a clattering noise and very hard to push. We have taken it back and he has changed the clutch mechanism under the base which has solved the clattering, but it is still really hard to push because of the suction. It is even lifting the carpet in one room. Can you tell me what the possible reasons for this could be? One thought we had was that the little rubber wheels on the bottom cover could have worn so the hoover is closer to the floor
On the sole plate you should have 5 little wheels, these are prone to jamming after a while. You should make sure these are not jammed in anyway.\012\012You can release these with a screwdriver, but be careful not to prize too hard as you ... Dyson DC07 Bagless Upright Cyclonic Vacuum
No suction I have the central vac type. It has no suction at the can. I pulled the hose going to the walls and tested there...and nothing. I removed the dirt can and checked the motor ...it is spinning but does not feel like any suction. I checked the exhaust and it is pushing strong air out. I also cleaned the filter and still nothing. Is there a relay or something that would cause only exhaust air. I emptied the can of dirt and put it back together and have absolutely no air.....hear the motor
On some units there is a screen that protects the impeller of the motor. If this gets sealed off with debris then it is like putting a potato in the tail pipe of a car. Taking the top off the unit reveals the motor. DO UN-PLUG the unit first from th ... Electrolux Central Vacuum
Rotating brush will not turn om Vax Mach Air - VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum
... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum
Dyson suddenly hard to push on carpet
I know this sounds silly, but it works. Turn it over and wipe all the black residue off the bottom of it (off the plastic on the bottom that rubs on the carpet as you push and pull it). I thought my husband was out of his mind when he told me that ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
My hoover widepath tempo pushes easy in any hight when off, but turn in on and you can hardly push in forward. I took the beater bar off and cleaned everything and still having this problem
Make sure the beater bar is turning sometimes it will freeze up with dust and dirt will get inside the bearing caps on the end of the brush ... Vacuums
My dyson dc17 is very hard to push on a hardwood or carpet floor. When I take the canister off and push it while on it works great, so I figure the canister is giving me the issue. What o I fix? Thanks
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
My windsor sensor 12 inch vacuum is to hard to push. I bought a new one and its doing the same thing. My vacuum repair man says he cant fix the problem. My shoulders are sore from working so hard. Help
It\\'s possibly the type of carpet you\\'re using it on. The sensors use the brush speed and the amount of air flow to determine carpet height. Some berber, and tweeds make these things horrible to push. We sell sebo, who make the windsor and we\\'ve ... Windsor SR12 Sensor Bagged Upright Vacuum
Self propelled vac: goes great on hard floor or hard slick carpet. Goes backwards fine but will not pull itself forward very well. Requires some effor to push it forward. I have adjusted the cable so the lever on the motor goes as far forward as possible. Suggestions? Model U6446-900
Dear Nasherrill,\015\012\015\012I've found a friend! I thought I was the only person in the world who owned the Hoover Model U6446-900! This model does not appear on the http ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u
Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums
My Bissell Proheat 12 amp is hard to push forward(whether on or off). There is a loud clicking noise when pushing forward and it ''jumps'' up on every loud click. It's OK when pulling backwards, sprays and vacuums up water. Belt appears OK. Thanks
I had this same problem and here is what solved it for me. On a previous cleaning session, my wife decided to take the two front screws out of the clear plastic shroud that covers the brushes in order to clean behind it. Upon re-installation, she did ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
I have a dyson dc21. All the sudden the hose is hardly suctioning up anything. If I take the canaster off, the top air hole suctions extrememly well, but when I place that canister back on, the suction is not going thru the hose and picking anything up. I have squeezed the hose, I feel no air leaking and do not feel any blockages...what could be wrong. It worked fine the other day and today, it won't pick up a piece of lint!
... Dyson DC21 All Floors Stowaway HEPA Bagless Canister Vacuum - Iron/Titanium/Yellow
My quite new neumatic henry hoover is really difficult to push - you need all your strength. I do not have the brushes down and its still really hard to push - can anyone advise? thanks
... Henry Numatic "" Canister Vacuum
The vacuum is very hard to push on carpeting even when on hard floor level.
... Hoover Tempo Widepath Upright Vacuum - Blue
Bad smell after using my windtunnel for a couple of minutes i noticed an odd smell. i turned it over and checked, the belts are fine but i cleaned out the hair anyway. after doing that the self propel seems to struggle and it is hard to push. when i look through the window on the top i can see the brush spinning freely but then when i push it, it slows down dramatically and then picks up again. the suction is fine. what do you recommend?
It may be the roller bearings? ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum
How far down do i push the attatchment hose on the reconery tank it is very hard to push down on the hoover shampooer
You want the top of the attachment level with the top of the tank, this way it will create a seal so you have suction through the hose. ... Vacuums
My Oreck XL 7000 is hard to push through a modest pile carpet. They gave us a shag attachment but all that does is push the carpet down. It is not ususable for us with bad backs etc.
... Oreck XL2200 Bagged Upright Vacuum
Hissing noise on my Vax mach air - VAX Appliances Vacuums
... VAX Appliances Vacuums
My Windsor Versamatic plus has all of the sudden become very hard to push. I maintain this vaccum very well. It picks up fine, just to heavy tp push apparently
Likely the wheels are frozen with thread and hair at the sides of the wheels. Check for free movement of each wheel and pick out the debris around any that are hard to turn. Long needles and tweezers are good tools for this. ... Vacuums
I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?
Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
Hard to push
Since I could not find help on the internet, and you guys only wanted to charge a fee for information (which is fine, by the way, although I declined) I called the toll-free help line I found on the Dyson web site. They walked me through a series of ... Dyson DC07 Bagless Upright Cyclonic Vacuum
My oreck is very hard to push. what could be the
Clean and oil wheels ... Oreck XL2000 Bagged Upright Vacuum
Vax 6140 not pushing water through water tube