Having problems with your Vacuums ?

Kenmore progressive canister vacuum model 116 52612205, I have power and suction but the powerhead motor doesn't come on to run the brushesdo you have a solution


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore progressive canister vacuum model 116 52612205, I have power and suction but the powerhead motor doesn't come on to run the brushesdo you have a solution


... Vacuums

I have a VX3000C Broan vacuum and the motor sometimes runs lower and comes back to normal time and time. Plus, now it lamost stops before coming back to normal speed. Can someone explain to me what that might be or if it did happen to someone else? It doesn't stop, but runs at very low speed and come back. It is like if a connection is not made properly. But it does the same at my 3 connections and I did check the one on the vaccuum itselfs.


... Broan-NuTone VX475 Bagged Central System Vacuum

My Miele Solution HEPA 5000 vacuum cleanr gives off a burning smell but will continue to run with a varying motor tone. I have not run it for more than a minute like this. I have reviewed responses to similar problems but cannot figure out how to access the motor. Can anyone advise?


... Miele S318 Bagged Canister Vacuum

I have a Electrolux , EL6988 Canister Vacum, howeveer the brushes and motor will not run when turned on. I have take the plates and cleaned around the brushes, but it will not come one. The vacum comes on but the motorized bushes do not activate. Thanks I have lost my owners manual, and have looked for the reset button and can't find or know where it is located. Any suggestions.


I need the molded wire harness inside the plastic wand ( one of the prongs is broke off) What is the part # or where can I buy it? Model EL6988 ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have a Filter Queen Majestic 360 and am having problems with the powerhead. There is a loud rattling noise in the powerhead, especially when I vacuum thicker carpet. I have replaced the motor, roller brush, and belt, but the rattling remains. It sounds like it is coming from the roller brush area,and when I turn the powerhead over, it rolls free and sounds fine. Any thoughts?


Hi there, as per your information i guess its a problem of power transformer. He can't supply the proper power in the motor & thats why the noise will come from the transformer. Thanks & waiting for your feedback. ... Filter Queen Majestic Canister Vacuum

Vacuum won't run light comes on but vacuum doesnt


... Panasonic MC-V5745 Bagged Upright Vacuum

Cleaning solution does not come out of the rotating cleaning head or the hand-held nozzle the solution pump seems ok but does not run (electrical continuity check between the two leads on the pump show very low resistance so they seem to be intact) - no dirt or blockage is apparent (it is a very simple device with 1 moving part wires to the pump also pass a continuity check THERE IS NO VOLTAGE on the pump leads from the control circuit board when I turn on the "manual" cleaning mode - a


You can contact Bissell directly at the following\015\012\015\012For UK inquiries:\015\012Monday - Thursday 9 am — 5 pm\015\012Friday 9 am — 4 pm\015\012\015\012BISSELL Homecare (Overseas) Inc ... Bissell SpotBot Robotic Wet/Dry Vacuum

No suction After taking the vacuum apart, I noticed there is no suction at all. The motor runs, belt runs, but no suction coming through.


You have a clog somewhere in the vacuum. Check the hose and the little trap door on the underneath side of sweeper.Does the brush turn? If not, then the belt that drives the brush is broken. Replace the beltJim ... Hoover Tempo Widepath Upright Vacuum - Blue

My irobot scooba does not spray cleaning solution out after about the first 30 seconds it is running. I have tried all the suggestions in this post with the suction bulb to charge with air, and then with water to clean it out. water does come out of both valves when forced with the bulb or immediately after using the bulb to charge it. then after it runs for about 30 seconds the floor is dry.


... iRobot 5800 Scooba Vacuum

My kenmore vacuum model 116.36933502. It has no suction. I have cleaned out every spot,taken off the back and still nothing. The motor runs but doesnt seem to be at full power. The agitator brush works. When it broke i seemed to smell something and since it has no belt. Does this possibly have to motors?


... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

I have a Kenmore Model 116 26312603 sweeper. The vacuum motor does not run, the power head does run. What is the most likely solution?


If the switch is a simple on/off switch,it could be that.Make sure it is unplugged.If you take the switch apart,twist the two wires together,and cover with electrical tape.If you do not have electric tape,make sure the connection is off of the ground ... Vacuums

Motor dying? recently my herritage has been sounding sick, i tried to use it the other morning and it barely could blow up the bag, there is also a hot smell to it when it is running, the motor doesnt sound as powerful as it use to. Any suggestions?


Replace the carbon brushes in the motor. ... Kirby Heritage II Vacuum

I was using my Heritage 11 vacumn with the hose attachment and the motor shut down like the power went off .When you push the switch on the housing the light comes on but the motor does not run.


Hi, the motor could be overheating. Most vacuums have a heat sensor that shuts the vac. off if there is a clog. Let it sit, feel if it's hot. If so you may have a blockage of dirt etc. Try to clear it, let it cool and tart it up. I hope this helps, i ... Kirby Heritage II Vacuum

I replaced the powerhead drive belt. Now (2 times) while vacuuming the powerhead motor appears to run backwards. Because the metal pully which has left hand threads on it will backout / unscrew it self. Prior to this belt rerplacement it functioned properly. Thank You Bob


Look at your power head motor. If you see a fiberglass looking sleeve on the shaft where the belt attaches to it, you need to remove that. You can slip it off, chip it off, or break it off piece by piece. You can usually use pliers and break it into ... Rainbow 75th Anniversary Canister Vacuum

Miele seb 213 Powerhead is getting ac power but there is no power to the motor. The light comes on and I get 120V on the ac side of the circuit board with a meter but zero volts on the dc side.can I replace the board or do I have to replace the whole Powerhead?


... Miele SEB 213-2 Vacuum

The pile adjustment wheel on my Sebo X4 has come off; I ordered a new wheel thinking that it would come with the PIN/AXLE but it doesnt. What do I need to order noe? I cant seem to find the pin as a spare part. Dp I need to order a servo motor? Many thanks Hannah


... Sebo X4 Bagged Upright Vacuum

We replaced the motor on our electrolux epic 6500 but the temperture light comes on and machine willnot run.


If you replaced it yourself with an original motor you have the thermal temp wire crossed over inside the body housing. This canister has a VERY specific almost foolproof harness. If you look carefully at the wires the only reach to their exac ... Electrolux Epic 6500 Vacuum

Motor running good but the water isn't coming out of either the bottom or the hand held tool


Make sure your recovery tank is pushed down snug,somtimes it just need to prime itself,I had the same problem with my hand held tool, and that seemed to do the trick,after it pushed down,turn on power then wait about 10 seconds then turn on heater. I ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Wiring diagram I havea Dog and cat appart and are trying to understand the wiring. From the power side I have a black then another black for a individual terminal each and 2 x blue coming from a single terminal on the 3 pin plug side. This is passed thruogh the switch to a 4 x pin terninal strip that has a brown yello blue and blak from top to bottom. Can any body help me with a wiring diagramm so I can traced these wires?? The problem with the vacuum is that the motor is not running. I am tryin


Hello, First check the cord to make sure you have continunity throw both leads, check\015\012them at the cord reel, there are 2 wires hooked up to it, if not then\015\012the cord is bad. Check the swith also, the next cause would be the\015\0 ... Miele Cat & Dog 326i Bagged Canister Vacuum

Aquavac runs for short time then cuts out blowing the RCD . Have rewired mains cable thinking a broken or loose wire... still same problem. Have also noticed that a lot of sparks etc coming from the motor brushes. Vac approx 10-15yrs old.Aquavac is model 6310B


... Vacuums

When we plug in the hose the motor in garage runs but no air or suction comes out of the outlets. we cleared all the lines too.


Check to see if you have suction at the unit. If you have suction at the unit, your pipes are stopped up. If you don't have suction, you have a pipe loose under the house. Also you could just have a stopped up hose ... Electrolux Centralux Vacuum

Solution doesnt come out nor does water. - Bissell 9200 Upright Vacuum


Ensure you have water in tank and solution (or water in solution tank). When you start the vacuum up, the pump starts to prime itself. If you have air in the system, it takes a little longer to prime. Allow the vacuum to run for 1 minute before attem ... Bissell 9200 Upright Vacuum

Water doesn't not come out for rug cleaning ...pushing the switch....no water...motor runs....


Check to see that there is no clog in the sprayers. Take the tank off and there are two red sprayers. pop them off with a screwdriver and use needle nose pliers to take the retainers off. The sprayers will pull off and use a paper clip to push throug ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My carpet cleaner is not spraying out water or solution. motor is working, heater is working but nothing coming out when i press the button


Check if bottom of solution tank and/or lines are gummed up. Clean and blow out lines and inspect check ball assembly.\015\012Hope this helps. Could use more info.\015\012Bob ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0624 seconds