Having problems with your Vacuums ?

My Bissell proheat 2x will not stop spaying when the trigger is depressed, This happens only after the power is turned on and continues until the tank is drained or the power is cut.

\015 All fittings are clean and free of debri. The hand tool will spray independently but the floor sprayer continues to squirt\015

Answers :

I assume you mean that once the trigger is depressed it won't go back to it's original position. Like it's stuck on. I would look in that area for a broken or missing spring. I would also trace the control from the trigger to the valve that it opens and see that there isn't any build up keeping the valve open.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bissell proheat 2x will not stop spaying when the trigger is depressed, This happens only after the power is turned on and continues until the tank is drained or the power is cut.

I assume you mean that once the trigger is depressed it won't go back to it's original position. Like it's stuck on. I would look in that area for a broken or missing spring. I would also trace the control from the trigger to the valve that it ope ... Vacuums

I have a Hoover Platinum carpet cleaner, and it has stopped dispensing cleaning agent and water. This model has a separate tank for water and separate tank for shampoo dispensing. It also has a power hand unit that dispenses shampoo. All along the hand unit has continued to dispense shampoo. Symptom #1, the water tank seemed to be taking on shampoo, as it was getting sudsy. Symptom #2 - On wash mode, nothing would come out, on Rinse mode, sudsy water would come out. Later, symptom #3 - not

Somewhere on the outlet is a control tap thats driven by a rubber band and something is up with this control ,best advice here is put it in the boot of the car and take iot to a hoover dealer ,they will do it seconds for you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos

It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

My Discovery 4210 Roomba will run normally for about 20 minutes on a smooth, wooden floor. It then begins the following sequence: run forward a few inches, turn in a tight counter-clockwise circle a few revolutions, stop, power off a few seconds, power up, repeat cycle from forward run. The sequence can be repeated seemingly endlessly if I don't turn off the power manually. I've replaced the motor, and led revolution sensor system on the left drive wheel. I've blown the dust out of everywhere. A

This robot vacuum has a electronic micro processor that controls the unit and tells it how to operate and where to go based on programmed parameters. It's quite a technical marvel. I have dropped a link here for contacting the company tech support li ... iRobot Roomba 560 Robotic Vacuum

Stops Immediately. We have a Beam Serenity model 2100 installed in the home and when the hose is inserted into the wall it turns on for a few seconds and then shuts off on it's own. Turning the handle's power switch off/on restarts the unit only to have it once again stop after a few more seconds. The canaster is clean. What could be causing this stopping issue? Thanks.

The Relay Control Board in the 2100 is bad. Replace and it should work just fine. ... Beam Industries 2900 Serenity Plus Central System Vacuum

CUTTING OFF Our Dco7 cuts off after a few minutes of use. If we wait a few minutes and power it back on it will turn on but turn off again by itself.

Ok What is probably causing the problem is an internal error inside the vacuum. What I recomend you to do is take it back where you bought it and tell them what ever is wrong with it.PLEASE RATE MY ANSWER AS SOON AS POSSIBLE! ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My bissell power trak just stopped working i turned it off and a few hours later i turned it on again and it will not work. I switched over to an outlet i know works and it still didn't work I checked the outlet after and there's still power there. Is there an internal fuse?

... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum

When the power head is turned on it goes from green light to red light and stops. The belt is fine and there is no obstructions in the brush to stop it from turning.

This will happen only when the brush or motor does not turn the right speed \015\012make sure to pull the end caps off the brush and clean any hairs or fibers from it\015\012the motor you can try and turn it by hand with out the belt on a ... Fantom Vacums Lighting Canister Vacuum

Roller I recently removed my roller to cut all the hair off it and when I replaced it everything snapped right in but when I turned the power on the power worked but the roller wouldn't turn

Hi.\015\012\015\012Did you put the drive belt back on the roller ? ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

How do I fix Bissell Quicksteamer leaking from water tank through wheels? After I place the filled Clean/Solution tank on the Lower body of the QuickSteamer, water pours out from the body of the machine through the wheels even before I turn the power switch on. I checked the tank and there are no holes in the plastic tank.

I have the same problem... seems to be because of a bad, or worn, rubber gasket. ... Bissell Vacuums

Miele Blue moon vacuum motor surging on and off and power light flashing. After many surges of the motor (on->off->on-> off etc), the motor no longer attempting to start as ferquently ie. now off for many seconds and may turn on for 1 second.. sometimes stops turming on and just power light flashes. There is also no voltage at the plug for the hose for the power head. I noticed that the vacuum first started having probs when hair was caught in the power head and the ovetrheating light went on

... Miele Blue Moon Bagged Canister Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums

It won't turn on. I have partially disassembled it and have continuity between the power cord (wide blade) and one of the connectors where the switch assembly snaps in. Also, switch is working fine. There is continuity across it, then no continuity across its connectors when the switch is pressed. Not sure what to try next.

\015\012Please provide the make and model. Thanks. ... Vacuums

Shark s3325 stopped working while steaming; thinking the unit had ran out of water I allowed unit to cool before refilling, however unit over flowed with only 700ml water added. When I plugged unit back into outlet it would not turn on (red light was not on) but I hear a click upon plugging in unit, when turning unit power button on and when turning on the handle switch. Please advise how to resolve this problem.

... Euro-Pro S3325 Handheld Steam Vacuum

My dyson DC05 has been playing up for a while. The motorhead would start fine with green light on and after a few minutes would stop and light would go green. then the power would go on and off - seemed to only work when I had the handle a certain way. Now no power at all. is there a way that I can check if its the power in the handle section as thats the only way you can turn this machine on? Thanks in advance

As the wires that control the motorhead run all the way down the hose it is a break in the wires you will need to buy the hose assy sorry its not thesort of thing you strip down and repair  ... Dyson DC05 Bagless Canister Cyclonic Vacuum

I have a miele S712 (2 yrs old worked fine yesterday) - I had been doing some diy work inside and had the vac on just to reduce some of the dust in the air - after a while the vacuum fizzled out. I guessed it had overheated and took it outside to cool down - when I tried to turn it back on pressing the power button gives it power and it starts to **** but it won't STAY on, soon as you release the power button it stops, and the orange bag indicator is showing full. As I have a compressor I took

You have got dust in the micro switch and it is not latching on, if you look at this and clean it, that will solve your problem, however blowing the motir has probably wrecked the motor bearings. ... Miele Vacuums

The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn

The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums

I have a tank style vacuum. When I vacuum with the power head it dims and slows down when I push the power head back and forth, but it powers back up louder when I stop pushing it If i remove the powerhead from the hose the vacuum works fine.

Most likely the belt. Thats the cheapest so try it first ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Intemitant power it mostly starts when you first turn it on, but then seems to lose power very quickly until it stops completely.need to know how to strip it down to have a look if there is a lose connection.thankyou

Hello,\015\012DO NOT TURN ON THE KIRBY ANYMORE UNTIL YOU GET THIS FIXED!!! (not even to show someone what it sounds like)\015\012\015\012Your carbon brushes are worn out and will cause damage to the armature if you run ... Kirby Ultimate G Bagged Upright Vacuum

My purple Dyson Animal (without the ball) isn't working correctly. When I turn it on, the red power light, as well as the medium pile buttons flashes. When I first turn it on, the brush rotates for 3 to 5 seconds, then once I start moving the vacuum, it stops and that's when the lights start flashing. I've checked the filters, they are dry and installed correctly. What could be the problem?

I need help repairing my Dyson. I cannot push the buttons down to select Short pile/Medium pile or bare floor. The buttons will not push down at all. It will not allow me to select anything. I have very short pile carpet so it does not pick up that w ... Dyson DC28 Animal Bagless Upright Vacuum

Dyson 28-animal- Power brush stopped working and power light and carpet level buttons all are blinking. Per the instructions vacuum needs reset by turning it off for 30 seconds. However after doing so it does not reset and work. Help!

... Dyson DC28 Animal Bagless Upright Vacuum

I own a Sanyo 35s 3.5 Rice cooker that has stopped cooking and heating. Power is going to the unit power light comes on. We have checked to make sure that the unit was turned off before unplugging as per the instuctions. Unit was new in Feb 2010 and well taken care of. Anything we are missing here?

If you have been washing or scratching the inner pot with something sharp or harsh like a metal spoon or hard sponge it could cause that and even electric shocks. try changing the pot ... Vacuums

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it

The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

Power problem I have my Progressive with direct drive for 3 weeks. I was using it today then stopped. When I went to turn it on again nothing no power at all

With out checking it, it is hard to say, I think there is a reset, did you push it? But you do have a years warranty on this, that it into Sears for repair. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Power problem I have a Generation III and lately the power button doesn't always work when it is pressed. You have to click it a couple of times and then it will turn on and sometimes it will even stop while I'm in the middle of using it. Thanks for your help

I would replace the power switch. Here are the instructions for the repair...\015\012http://rev ... Kirby Generation 3 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1034 seconds