Having problems with your Vacuums ?

Trying to replace the belt on my Kirby. I have the plate off but I cannot get the roller brush out..husband and I both tried.


Answers :

Turn it up where you can see the roller push it in and slide it to the back are the frunt it should come out
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Trying to replace the belt on my Kirby. I have the plate off but I cannot get the roller brush out..husband and I both tried.


Turn it up where you can see the roller push it in and slide it to the back are the frunt it should come out ... Vacuums

I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?


If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the


Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus


... Bissell 6595 Lift Off Bagless Upright Vacuum

How do I get the beater brush off of the vacumm to replace the belt? The vacumm is a Shark roadstar . I can get the belt on the one end but I cannot get the brush up to put it on that end. Judy It is a Shark Roadstar EURO-PRO Model No. UV208C


... Vacuums

My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou


Try this link belowhttp://www.ereplacementparts.com/hoover-u6630900-windtunnel-selfpropelled-bagless- ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Trying to replace belt on hoover convertible bagless upright u8188900. belt replace # 38528-049. i have opened vacuum and put belt back on, but it will not get tight enough around the motor gear and the brush spool to be able to activate. am i missing something? mike


... Hoover Vacuums

Generation 4 Apparently, my belt came off while vacumming. I had a lot of hari entwind on the roller, so cleaned off the hair.... but now I can't seem to get the belt to stay "in place". Is it supposed to move around on the brush? or be held in place? It seems to me when I try to get the hook to grab ahold of the belt, it is going tohe wrong way to grab it. Please HELP!


First off get a new belt, I am sure this one has stretched. Then put the belt around the brush roll, put it in the center, put the bottom plate back on. Then turn the big knob on the front and turn it until it locks, you will know if it grabbed the ... Vacuums

I am trying to replace the belt on my bissell. The directions state "remove the screw that holds the red retainer in place, set red retainer arm and screw aside. I see the red retainer but can not get it out I also can not remove the black brush arm that holds the brush in place. I have tried and can not remove it.


Hi, Did you release the handle first before you flipped it over?Have you removed the screw and it still won't come out, or is it stuck even after the screw is out?Are you having trouble getting to it?Please r ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

The brush is not moving on the vaccume. I'm pretty sure that the belt is busted. I cannot see how to get the shroud off, so that I can get to the roller and belt. It all looks and feels like one piece, even when I start removing screws. It is a bag-less vac. The model number is - v1310rs. Thank you.


I know on my Eureka I had to remove a couple of screws on the bottom and then get a flat blade screwdriver and wedge it on each side of the base kinda next where the end of the roller would be and it snaps up and off. Really weird I thought but that' ... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?


First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]


Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a dyson root cyclone. i dismantled it to replace the belt, it is not the belt which is on the roller brush, it is the belt which is from the motor, it was easy to take out as it was broken, i will get new one tomorrow now im wondering how do i fit it in.


The belt that fits on the motor is the same belt that drives the roller brush, all you need do to gain access is remove the sole plate, normally attached with 3 quarter turn connectors, use large flat screwdriver to turn them ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I am using a Kirby Hertigae II shampoo attachment and the belt broke, I am trying to replace the belt, but cannot remove the bottom brush that the belt hooks onto.


Try using a pair of pliers on each side to remove the screws you only need to remove 1 ... Kirby Heritage II Vacuum

I have a Miele S1721 Powerhouse upright vacuum. When the belt broke I took it into the shop (because when i tried to replace the belt, the tension was so tight I couldn't get it back together!!). When I got it home I DISCOVERED THAT THE HEIGHT ADJUSTMENT DIDN'T WORK anymore. It seems like it's set really hight, because it no longer contacts and brushes the carpet. So it's now useless. I went back to the shop and the tech denied that there was anything wrong. (I didn't have the vac with me). No


Hi\015\012The Miele uprights (S170 and upwards) with the Powerhouse title are ALL Panasonic uprights which have been at one time sold in the UK. Therefore the upright may use TWO drive belts which need to be looked at: Take off the sole plate a ... Vacuums

I can't get the latch that connects to the brush head to engage. Thus the vacumn is extremely hard to push. It has suction, extreme suction. Rollers appear to be dragging. I've tried to remove and reinstall the head several times but cannot seem to get the latch to engage. Please advise.


It sounds like something has come out of it's socket. If the brushroll won't turn rapidly, your clutch is worn out ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Need to replace the main belt on my Bissel 1698-P. Can't figure out how to get the belt around the brush roller. Have the top off. Cleaned the water tubes, didn't let the water come down.


Remove belt access door at left front of unit.\015\012\015\012Unplug the unit. Remove the two solution tanks.Remove spray tips from guides.Remove the brush and cog belt by removing the screw from the orange retaining collar.\015\012Remove belt ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

I am trying to replace the cable and actuator on a Hoover windtunnel self propelled vacuum. but I cant get the top or hood off the get to them, I have removed all the screws I can see, roller, belts..what am I missing?? thanks so much for any help


Hi there SmartAlec from NelsonVacuums.com.au here. You will need to remove the knobs for carpet/hard floor selection and the carpet height to remove the cover they act as k ... Vacuums

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

We have the Kirby G six 2001 Limited edition vacuum and we cannot get the belt to hook on to the roller brush.


... Kirby G6 Bagged Upright Vacuum

I replaced a torn belt and now cannot get brush back in place


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=555430\015\012Generic problem for all Vacuums\015\012I replaced a torn belt\015\012Posted by brendais on Apr 29, ... Vacuums

My Hoover Dust Manager roller brush is not turning It may be the belt but I dont know how to get to it to replace i Can you help Michelle


... Hoover Vacuums

I cannot remove the roller brush for shark vacuum


Remove the rubber "bumper" material from the outer edge. Small slits are exposed where the roller is attached to the rest of the vacuum. u can figure the rest out. I wedged my finger in between the roller edge and lower plate. Use whatever you want. ... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0930 seconds