Having problems with your Vacuums ?

I don't know how to fit the belt


Answers :

Fit the belt ON WHAT ????
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Oreck vaccum when i put a new belt on, the belt rubs the side of the wall of the vacuum gets real hot and busts. is there any type of washer fitting that goes on the vacuum to hold the belt in place? i dont know i need help thank you. you can reach me at [email protected]


The belt must not be running true to the pulley. You may need a brush roll, but also check the motor to make sure it isn't moving inward after the belt is put on. ... Oreck XL Ultra Bagged Upright Vacuum

Need to replace 2 belts on the Panasonic MC-UG302 upright hoover and I dont know how to do it. Is it possible to get a brief discription/diagram of fitting belts from somewhere. Tks


... Panasonic Vacuums

Hello, my names Travis. I was contacting you in concern of my Kenmore Quick Clean 12AMP Vacum Cleaner. My girlfriend took the bottom off the vacum and removed the belt because the vacum wasnt picking up. I know have a new belt i just dont know where to put it on the vacum to reinstall it


Look for grooves on the motor shaft and on the brush shaft. ... Kenmore Quick Clean 30012 Vacuum

Missing belt I have a Dirt Devil, Touchup, upright vacuum cleaner (model 084015). I need to know what belt fits this model.


Thanks for the info **** now stick it up your ***! ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

My belt broke. I have a replacement. I dont know how to install the replacement belt.


There's a plastic cover over the agitator. (the part that should spin, with tough bristles)Unscrew it. Pull out the agitator. Put the new belt over the 'spinner' (the part that's connected to the motor) and the special pafrt of the agitator. Sn ... Vacuums

Moter belt my moter belt broke and i dont know how to replace it


You can find the manual for your vacuum by clicking on this link: http://www.bissell.com/images/UserGuides/1697_207.pdf ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Belt I have a bissell pro heat model number7901-1 and i dont know how to put the belt back on. The old one broke and i cant find my book.


First take off the cover on the left side of the top cover, then turn it over, remove the screw holding the red lock and pull the cap and brush roll out, remove the cap, remove the cogged belt, then you can put the new pump belt thru that slot, put o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My hoover belt keeps burning when i replace it. i dont have the manual so i dont know what im doing wrong.


Probably when you close it back together, there is a piece rubbing against that you do not see right away but could maybe hear it. ... Hoover Vacuums

Belt broke I have a bissell powersteamer and a belt broke and came out the bottom of it. I dont know how to put one back on it


There should be an access panel on the top side of the cleaner. Pry this open with a screw driver and this should get you access to the area where the belt can be changed. ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

DONT KNOW HOW TO CHANGE MY BELT


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=698891\015\012Generic problem for all Vacuums\015\012DONT KNOW HOW TO CHANGE MY BELT\015\012Posted by m ... Vacuums

Smoking after fitting belt on dc07


... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have acquired a second hand amway CMS2000 it needs a new belt by the lookds of it but i dont know what this vac can really do is it a carpet cleaner as well and what are the products and how do i clean with it.


... Vacuums

My Hoover Dust Manager roller brush is not turning It may be the belt but I dont know how to get to it to replace i Can you help Michelle


... Hoover Vacuums

D.d vaccum i have a dirt devil dynamite...i bought a new for it i put it on and not even 1 minute of using it the belt broke again!!!!i dont know whats going on do i have 2 put it on a certain way does it need grease or what!


Did you check the brush roll, if the ends aren't turning freely, then it needs to be replaced also. ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

I dont know where my Vacuum belt is located? - Eureka 4700A Maxima Bagless Upright Vacuum


The link below is the manual it will give you step by step instructions on page 19 how to replace belt and brushbar ..http://dl.owneriq.net/b/b7517422-db37- ... Eureka 4700A Maxima Bagless Upright Vacuum

I have a dc07 green and silver dyson and i dont know how to put the belt on


Go to www,dysonmedic.com then scroll to the bottom of the page and click on "DC07 belt and brushroll replacement guide". You will find an excellent illustrated step-by-step guide ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The Hoover steam vac dual v does not spin its brushes and I dont know how to dismantel it to view the belt .


There is no belt on the steam vac - it operates on air flow. Remove the brush and insert a flat screwdriver into the square hole. If it does not turn, the turbine has seized up and must be replaced. Remember that the brush will not turn unless the lo ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Dont know how to change the belt on a 1697 bissel powersteamer pro


There is a great video on the Bissell site. 1 min watching it shows you how.Basically you unplug it, take out the tanks, turn it upside down, remove the 2 red clips that hold the brush assembly, and lift the assy out, then replace belts. ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Dont know how to change belt on bissell pro heat carpet steamer cleaner


See thishttp://cache.vendaria.com/vpop/VpopV6.html?ct=13&ctname=CT630X556D630X390&fw=630&fh=556&logo=49&fv=10&ap=vnd_bissell_deap_cleaner_how_to&purl=MAIN_bissell_how_to_replace_upright_deep_cleaner_belts&i ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I LOST MY INSTRUCTIONS DISK TO MY KIRBY G SERIES AND I DONT KNOW HOW TO DO ANYTHING WITH IT. I JUST REPLACED MY BELT BUT IT DOESN'T SEEM TO BE WORKING AS WELL AS IT SHOULD.


We have a video, online and printed manuals HERE. ... Kirby Generation 3 Bagged Upright Vacuum

I have a hitachi 1300 upright hoover and dont know how to change sdrive belt


... Hitachi Vacuums

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I need to change the belt on my Bissell Pro heat. I dont know how to get to it!


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I don't know how to fit the belt


Fit the belt ON WHAT ???? ... Vacuums

I dont know how to change the belt on my hoover turbopower 4000


... Hoover U5264-930 TurboPower Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0700 seconds