Having problems with your Vacuums ?

Need a picture of belt on hoover windtunnel

\015 Trying to change old belt .. cant figure out ho0w new one works\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need a picture of belt on hoover windtunnel

... Vacuums

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v

I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Ihave a Hoover Windtunnel self-propel model U6445-920. The belt from the drive motor to the big wheel will not run in the center of the wheel. The belt runs about 1/3 off the wheel. I have tried several new belts and still the same problem. What do I need to do to repair this problem.

The large wheel may be worn off center. If the belt stays on and is not thrown, you can run the vac. if there is wobble in the wheel causing a genuine belt to slide off replace the wheel mechanism. ... Vacuums

Need help with Hoover S3765-040 WindTunnel Electronic Bagless Canister Vacuum. The belt that rotates the brush keeps slipping off. what to do?

The belt could be stretched and that could be causing the slip. Or you could have the wrong belt if you've replaced it recently ... Vacuums

The belt needs replacing - Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Here is the manual to your Hoover U6630www.thinkvacuums.com/pdf/uprights/Hoover_U6630.pdfit goes into detail on how to change the belt and which belt to purchase. Ask for a flat belt Hoover part No. 38528035 when you're going to pur ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I need to change the small belt - Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Just remove the cover on the bottom of the vacuum by loosening the screws holding it on. Once they are off, you'll be able to slide out the rotating brush, and you'll see the belt there. Look inside the vacuum also, as when they break, they can sprin ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I need to replace belt #38528-033 on a Hoover WindTunnel vacuum model #U5463-960. I've had the vacuum for a long time and have misplaced all operational and instructional info that came with it. Any help would be appreciated. Thank you.

Replace the belt on a hoover washing machine ... Vacuums

Hoover self propelled bagged windtunnel upright model #U6435-900...how do you remove the green plastic shell cover to get to the part that secures the v belt...we need to secure the bolt and cannot get the area. Brushes and transmission wheel not rotating? thanks

Greetings from GoVacuum,\015\012\015\012Here's a great video repair tutorial that we've put together to try and help you with the repair on your Hoover WindTunnel. I hope that this helps you with your repair. If you found this solution ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Replacing a hoover windtunnel vacuum belt U8147-900

This has no belts, there are 4 small brush rolls, if the ends are bad and not turning then you will need to replace them. The newer ones have metal instead of plastic so are better. Should be able to buy the brush rolls at a local shop or from ... Hoover U8147-900 WindTunnel V2 Bagless Upright Cyclonic Vacuum

Hoover WindTunnel, month-old belt, now too large to turn brush

I suspect you have been bitten by the Chinese bug.\015\012\015\012A very large percentage of replacement parts for all manner of appliances and vehicles are now being conterfeited in China who we should know by now has no respect for the intell ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Were can I order a belt for a HOOVER MODEL U4423 ? The belt number needed is # 49258AG

Go here > http://hoover.com/search/?q=49258ag&x=17&y=8 for your belt ... Hoover Vacuums

How do I replace a hoover windtunnel belt - Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Here is a link to the manual and to the belts you need.\015\012\015\012\011\011\011\011\011\011U6439-900 Manual \015\012\011\011\011\011\0 ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Belt for Hoover Windtunnel Dirt Finder Model # U6485900

... Hoover Vacuums

I have a Hoover TurboPOWER 7300 Windtunnel V2-belt change

1. Remove the 4 screws holding the bottom plate.\015\0122. remove roller and old belt\015\0123. install new belt on motor spindle first and then on roller.\015\0124. pull roller, stretching belt, set into roller cavity.\015\01 ... Hoover U5444-900 5100 Wind Tunnel 15 Inch Wide Hepa Filter Bagged Black VacuumVacuum

V-belt flapping on Hoover Self-Propelled WindTunnel Bagged Vacuum

... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

Hoover WindTunnel Self-Propelled V Belt

I had this same problem with the V belt on my Hoover Vaccuum.\012\012There are three (3) basic things that will cause the brush roll not to spin.\012\0121. When handle is upright, brush roll is OFF.\0122. When switch is set for HARD surfa ... Hoover U6441-940 WindTunnel Bagged Upright Vacuum

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?

I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Drive belt keeps breaking on hoover windtunnel vacuum. Drive belt won't turn the agitator. Belt is new. Small belt is new. Agitator is new.

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Belts I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do t

It is the flat belt that gets stretched and should be replaced at least every 6 months. The V belt wears down so it won't it right in the brush roll V. Maybe the belt tensioner wheel has a problem, sometimes they get hook up and won't engage the V ... Vacuums

Hoover windtunnel u6476-910. Brush does not roll. Flat belt and other belt are good. The other thicker belt (called V belt?) does not have tension with the brush roll. How do I make sure it is engaged? Is there a fix? Settings are in "Carpet", "Roll-on", etc. Cleand all hair and bags/filters already.

These machines had a defective switch and a bulletin was sent out to all service depots. If you contact any Hoover Warranty Depot, they will replace the switch, wiring harness and tool receiver under a no-charge warranty. It doesn't matter how old it ... Vacuums

New Hoover Windtunnel belt slips off

... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Need instructions on how to replace the belt on a hoover dirt finder model u5321-930

You can download the manual from the link below:\015\012\015\012http://www.hoover.com/Media/ModelPDF/U5468900.pdf\015\012\015\012Please update the question & let us know if the information given was useful to you - Good Luck! ... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

Hoover Windtunnel Hello! I had to change the flat belt on my vaccum and now the belt won't stay on. I can replace it, use the vaccum, then the next time the belt comes off. Is there something I did not do right? Thanks for your help! Jennfer

Your belt may be twisted inside-out. Be sure the printed marks on the belt face away from the pulleys and shaft. The printing should face you. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0946 seconds