Having problems with your Vacuums ?

I have a kirby G7D ultamite, I recently replaced the switch, it worked for two weeks then it hasnt turned on since. Also I checked the cord, it has power going to it. Please respond asap thank you.


Answers :

The switch has probably come lose, have you checked the motor to make sure it is good? Usually the cord will short out right by the motor assembly try to wiggle it while plugged in and see what it does, its most likely the cord I recondition kirbys and never have I had a problem with the actual vacuum only the cord.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a kirby G7D ultamite, I recently replaced the switch, it worked for two weeks then it hasnt turned on since. Also I checked the cord, it has power going to it. Please respond asap thank you.


The switch has probably come lose, have you checked the motor to make sure it is good? Usually the cord will short out right by the motor assembly try to wiggle it while plugged in and see what it does, its most likely the cord I recondition kirbys a ... Vacuums

Cord rewind The power cord is jammed and won't go in or out. I can't find a way to get the cover off to have a look at it. Any suggestions please? Power cord jammed won't go in or out. Can comeone tell me how to undo the casing to get to the power cord?


Which model do you have.. ... Vacuums

My dyson DC05 has been playing up for a while. The motorhead would start fine with green light on and after a few minutes would stop and light would go green. then the power would go on and off - seemed to only work when I had the handle a certain way. Now no power at all. is there a way that I can check if its the power in the handle section as thats the only way you can turn this machine on? Thanks in advance


As the wires that control the motorhead run all the way down the hose it is a break in the wires you will need to buy the hose assy sorry its not thesort of thing you strip down and repair  ... Dyson DC05 Bagless Canister Cyclonic Vacuum

Electrolux Centralux I have a Electrolux Centralux. When I plug the hose in at one of the wall outlets the motor will not start. If I go to the motor and slap the unit it will start.....then...it will not stop unless I unplug the power cord to the motor. If I plug the power cord back in, the unit will not restart until I slap the motor unit again. The unit has only been used 20 - 30 times. Any suggestions?? Thanks, Bruce


I dont know if you had your unit looked at yet but it sounds like the Power module is going. I repair the machines so I know some of the work. ... Electrolux Centralux Vacuum

Wont charge new roomba for xmas. lights on charging unit both flashing but no power in roomba. it worked yesterday when i got it out of the box and did a full clean. i feft it on charge over night ready for the clean today but when i got up no power atall please can you offer a solution. i have held down pock and start - no joy. i have checked the battery connections - no joy please help many thanks caroline


Did you try plugging in 560 driectly to charger then run it? ... iRobot Roomba 560 Robotic Vacuum

Our Winsdor Sensor XP12 does not show any power or lights, I did check the handle connection, it was fine. The power cord has been repaired with duct tape 3-4 x where someone has sucked up the cord, this may be the cause yet it ran fine last time it was used! so I am at a loss, please help if possible.08/31/2010 Steve


Any time the cord has been damaged badly enough to require taping, the possibility or intermittent "opens" exist. This means the wires are in contact much of the time, but will losed contact periodically. Even if it worked fine seconds ago, jigglin ... Windsor SR12 Sensor Bagged Upright Vacuum

Hoover Vacuum My Hoover cannister model s3614 "runabout powermax" suddenly lost power to the agitator roller in the rug brush. Where the wire cord enters the power brush, the covering has rubbed off exposing the wires which are not bare but still have their own covering. For a while the power came and went as I manipulated the wires but finally died. Is this something I can fix myself or is it going to be an expensive professional repair? (Warrantee has elapsed.) Thanks.


Our Hoover upright vacuum cleaner makes a very loud noise when it is running. What causes this? ... Hoover S3614 Vacuum

Cord rewind The power cord is jammed and won't go in or out. I can't find a way to get the cover off to have a look at it. Any suggestions please?


A bit late for the original questioner, but perhaps this will help someone else.\015\012\015\012There are many models of the Hoover Telios. This solution applies to the T5603 at least, but perhaps not to all models... sorry, I don't know about ... Hoover S3330 / S3332 Straight Suction Telios Bagged Canister Vacuum

I plugged it in, pushed the power button and it came on for about 5 seconds. Then, it shut off by itself. I checked the outlet and it was working fine. I then cleaned the brushes and tried again, but no power... Nothing. Could it be the cord??? Any other ideas? Thanks for your help!


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My electrolux guardian power nozzle took up a corner of a bed sheet and stopped working. I removed the sheet and pushed the sweeper reset and then discovered i had no lights on on the grip/handle. I checked the outlets an they're ok. what to do? please help. thanks, Duane


There is a reset button/switch on top or bottom side in most of the vacuums.Check out if there is one in your model.If no then its a internal problem.When the bed sheet stuck up in the unit.At that time the short happened in the unit and it stopped ... Electrolux Guardian Bagged Canister Vacuum

I have a Kenmore canister serial number DB12027279, model 116-2234590. The problem is that the power cord plug gets very hot. Please advise what to do. Thank you.


Just a suggestion, as the debris enters the machine, it has to pass the motor. The motor has vents around it. Enough "debris" gets in that motor, the motor starves for power, which inturns make the media, the cord, work harder.\015\012\01 ... Vacuums

I am trying to replace the power cord for my 82 year old father-in-law's Oreck XL 2600HH. He already took it apart. I need to know where the semi U shaped spring steel piece is supposed to go inside the Helping Hand Handle? Any drawings or schematics available? Thank you for your time. Arthur


That justs lies on the inner handle whenb you put the spring back. There should be two holds where each end of the spring sits in. ... Oreck XL Ultra Bagged Upright Vacuum

Smell/suction I have a Eureka Altima Model 2991 Type AVZ. I have suction when I use the power paw and attachments. I have all hoses clear. My brush is spinning and belt is not broken (I opened it up and checked), but I have no suction when I turn it on to vacuum my living room carpet. I also have a burning smell to go with it after about 30 seconds. I've never had a problem with this vacuum cleaner before.


Ours started smelling too, and it seems that the plastic end on the roller brush was melting. In process of finding rollerbrush for it now ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

Salton WD-1044 Instant Water Dispenser - This unit just quit working. - We checked the temperature sensors and power switch - Tested ok... Please advise what else could be wrong and/or how to repair. Thank you and have a nice day


... Vacuums

I have a bissell power steamer That is not spraying soap, only water. I have checked all the filters and belts that I know of I also tried to reprime the pump as indicated in the trouble shooting section. Is there anything else I can try? Thanks


If it spraying water, then the pump is ok. The valve at the bottom of the soap bottle may be bad. Also when you turn the smart mix vavle, does it turn easily or hard, if hard, try spraying some furniture polish around the knob and turn it to work i ... Vacuums

Does the trivac 1100 have a fuse? My machine has suddenly stopped.I have checked the fuses in the plugs and also made sure that power is at the wall socket. I can see what loks like a fuse holder in the top of the machine near to the on/off switch but it is very tight so I want to be sure that it is a fuse before unscewing it. Thank you Jim


... Philips Vacuums

Heritage 2 - black wire pulled out from motor assembly, comes from power switch. Where does it go? Need wiring pictorial and schematic/wiring diagram. Can anyone please help? Many thanks, Malcolm


... Kirby Heritage II Vacuum

Power cord can not find replacement power cord for power brush attachment on kenmore canister vacuum, model #2491290 power brush attachment model # 5491290. i can not even find those model #'s anywhere online, not even partsdirect.com. any help would be great. thanks, david


Call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est ... Vacuums

Got a Filter Queen Majestic Limited Edition, the one with the high and low power switch, an I have to change the power cord. How can I open the main unit to reach that power cord? Thanks,


First remove the top cap under your handle. \012Then, remove the three screws under the handle. \012remove the rubber cover on the switch\012undo the clamps on the side of the unit\012lift off the chrome cover with the cord on ... Filter Queen Majestic Canister Vacuum

No power to sensor SR 12. I also have cleaned rollers and filters and bags. I have reset the handle. When I hit the power the check brush and full bag lights flash once. That is the only power that is getting through.The unit was in storage for a bit and got wet but its been drying off for a couple months. Is there something I can check or replace. Its a great Vac.


... Windsor SR12 Sensor Bagged Upright Vacuum

I have cd mix 2, i lost the power cord, and i used a different 12v cord. The mixer played for a while then the power went off. I checked the fuse at the power supply it has continuity.


May be you unintentionally provided more voltage or current to the appliance and it has got damaged because i feel that if it played at first and then stopped then it might have got damaged due to overvoltage or excess of current .I would highly reco ... Vacuums

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u


Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

Replacing Power Cord Kenmore Progressive Upright


That actually sounds correct, if it's the model I'm thinking of. As long as you're talking about connecting to the wires that are held in by the wire nuts you should be good to go. \015\012\015\012-R ... Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum

Using my unit (owned about 6 years - great service so far) it suddenly quit ... no wind down or 'prelude' like whine - growl - etc. -- it just quit running ... suggestions? clear filters? done check power? how check power cord? done help ...


I agree with you having great service because mine only lasted two years. It sounds like the motor just worn out. If you don't smell any burnt electrical then replace the bushing for the motor. Good Luck ... Dirt Devil Reaction Twin Cyclone Upright Vacuum

The mechanism that rolls back in the power cord seems to be working slower and sometimes not at all. Was wondering if the mechanism in question has an adjustment to increase the tension on it so the power cord goes in faster like it used to. Thanks Rafael


It easy to adjust the roll back of vacuums the problem is hard to dismantle the unit to remove all the things to see the adjustment roll,all vacuums is need to remove all screw to open the unit even to replace the small parts like switch,and sometime ... Kenmore Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0681 seconds