Having problems with your Vacuums ?

How do you take the Shark G1477R apart? - Vacuums


Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do you take the Shark G1477R apart? - Vacuums


... Vacuums

TAKE APART A SHARK 3601 - Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum


My shark 3601 died on me. A replacement is on its way but I still wanted to take a peek inside. After trying to get it open for about two hours, I figured it out. You have to remove the small screws by where the handle goes in. Then you can work your ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

How do I take it apart? - Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum


Go to this link and download the nanualhttp://www.sharkcl ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

How do i take apart my shark euro-pro v1510 hand held vacuum cleaner


... Vacuums

How do i take apart my shark v1510 vacuum cleaner


... Vacuums

Bissell Healthy Home Vacuum brush stopped working. The hose attachment works fine, just the brush on bottom. Without taking it completely apart, it shows no sign of blockage. Any suggestions? Or, will I have to take it apart?


You will have to remove the bottom plate to get at the brush. The drive belt either slipped off or broke, this will have to be replaced. ... Vacuums

Hose is there a repair manual for the hose on this kind of vacuum?? it got clogged pretty good and I thought by taking the hose apart there was a place to take the hose out.... I thought wrong and now I have a hundred piece everywhere and no vacuum..


... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Vacuum, Hoover Elite 350. Rag sucked up how to take apart


... Vacuums

The thermal motor protector on sears model 116.35912 Kenmore vacuum won't reset. The manual says to wait 30 minutes and the thermal protector will reset on it's own. It appears I would have to take the vacuum apart to get to the thermal protector. Is it worth the effort or should I trash the vacuum?


... Kenmore Vacuums

TAKE APART SHARK S3601


There are two screws under "SHARK" decal, and three under steam mode decal (button that controls three steam options) ... Shark Professional Steam Pocket Mop - Model S3601 new

Manual for taking apart vacuum head for model 1163493592C


... Kenmore Vacuums

The vacuum stopped working when i was vacuuming. The bag had a hole in it so all the dirt and stuff where clogging the filters. I cleaned them and put a new bag in but it will not turn back on. So I want to take it apart to see if there is more dirt on the inside,


... Fuller Brush FB-PT2 Vacuum

Hi, I vacuumed a small rubber bouncy ball up into the vacuum by mistake. The suction is not as strong now, and I'm not sure what to do. Where I can easily take the hose apart (eg. at the handle places) I cannot find the ball. What do you suggeest?


... Vacuums

How to take apart vacuum wand of 11621614010 - Kenmore Vacuums


... Kenmore Vacuums

Take handle apart sebo vacuum - Sebo Automatic X1 Bagged Upright Vacuum


... Sebo Automatic X1 Bagged Upright Vacuum

Taking apart hoover core vacuum - Vacuums


... Vacuums

The retractable cord is stuck all the way out and will not go back in. Is there a simple way to fix this "disaster"??? without taking vacuum apart that is. And this is not my exact vacuum but I figure the cord problem would go for all of them. Ours is a ORANGE HEPA 360 Kenmore Whisper Belt 12 amp with PowerMate Model # 116.29219800


... Kenmore 27915 Bagged Canister Vacuum

I have a Hoover Turbo EmPower 4600 and the roller will not turn when we turn on the vacuum. The vacuum is fairly new, and hasn't seen too much use, but now the roller won't turn, so it's not picking anything up. There also doesn't appear to be a belt or any way to take this apart. Can you help me? Thank you!


The beater belt is broken. There are 4 phillips head screws on the outside (2 on top of the base on either side of the upright, and 2 on the front edge on the underside of the base near front edge). and 4 phillips head screws on the inside (holding ... Hoover Vacuums

My hoover vacuum runs for about 10-15 minutes then the saftey feature shuts it off(overheat?). i have taking it apart a cleaned it with no results, added new bag also. after an hour it cools down and works again. do i just need a new vacuum?


Do you have suction through the tools? Does it look like it picks up when it runs? The machine could be clogged and that would cause the problem, but unfortunately the sensor that shuts the machine off could be bad if the machine isnt clogged. Its no ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I have a Dirt Devil Upright Vacuum Model 088525B. I need to replace the power cord. How do I take the vacuum apart?


... Dirt Devil Vacuums

I have a Eureka Pet Pal and it seems to have lost suction on the main part of the vacuum. It looks like it sucked something up before it happened so I'm fairly sure that the tube is clogged but I don't know how to take the vacuum apart so that I can clear it out. Is there anyone out there than can help me figure it out?


... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430


Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I


You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

How to take apart a miele s5210 vacuum - Miele Vacuums


Found this:\015\012http://www.asciimation.co.nz/bb/2009/12/29/tearing-apart-my-miele-s5210-vacuum-cleaner ... Miele Vacuums

How to take apart vacuum to change the belt on a F 10051 01 Fantom vacuum


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0881 seconds