Having problems with your Vacuums ?

I have a dirt devil dynamite vacumm and am unable to get a new belt on, as I am not strong enough to stretch it far enough. Can you help me? Thank you

\015 I stated the problem above\015

Answers :

If you put the belt on the motor shaft first then put the brushbar through the belt then pull into position,here's the manual with instructions.
http://dirtdevil.com/file/244/
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a dirt devil dynamite vacumm and am unable to get a new belt on, as I am not strong enough to stretch it far enough. Can you help me? Thank you


If you put the belt on the motor shaft first then put the brushbar through the belt then pull into position,here's the manual with instructions.http://dirtdevil.com/file/244 ... Vacuums

Small belt driving the brush...stretched out with hair accumulated in groove beneath belt. Is there a clutch or other means of tightening the belt. Went to store found belt...same size, therefore previously assumed stretched condition does not appear to be valid. I'm missing something. Any help?


You do not by a belt by size, buy it by model only. A new Hoover belt will generally be very snug when installed. As heat builds from use it stretches and becomes worn sometimes as much as 30% oversize. Good that you have cleaned out the hair. Check ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

LOUD noise Turned on vacuum one day and it made a reallly loud noise like the belt had broken. So we replaced the belt correctly, and turned it on and the noise is still there it is also rattling violently. HELP PLEASE not exact same model but close enough


The armiter or fan is broken and if you get it replased it should work like new ... Hoover U5227-930 Elite Upright Vacuum

My dyson dc14 is making a very loud noise along with a strong burning smell and the brush is melting by the belt hope ypou can help me thankyou.


Your clutch is shot. It's an expensive repair. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a power drive baggless vacuum cleaner...it runs well, but suddenly it seems to have lost most of the suction coming through the hose and floor area. When I remove the dirt container, the suction below it seems strong. I have had it to repair twice--they have tuned it up and replaced all filters and belt. It still does not pick up well when I vacuum or use the hose. Can you help ?


There is something stopping it up,you will have to dissasemble the unit to find the blockage,this is the most likely problem. ... Hoover U6660-900 WindTunnel Bagless Upright Vacuum

My dyson dc 14 is not picking up as well as it should,but, suction still very strong when using hose with attachments, have checked belt and have checked for blockages. can any one help please?


Hi its Darran at Dyson.I would check that the brush bar is turning when you have the cleaner in the vacuuming position. To check this, make sure the brush control dial (on the cleaner head) is in the centre position and when you release ... Dyson DC14 Bagless Upright Cyclonic Vacuum

Lost suction I've only used this vacuum a few times, it's practically brand new. Now, one I turn it on, it sounds fine, and the hose feels as if it's getting some suction, but it's not strong enough to actually **** things up from the carpet into the canister. I have completely emptied the canister and bought a new filter. Nothing seems to help.


TOSS IT and forget it! I have never used a hand vac that worked that was worth the effort of turning it on .... I suggest they are all junk ... I found very few vacuum cleaners ... actually **** especially anything made by dirt devil ... I do have a ... Dirt Devil Vibe AllPurpose Hand Vacuum Bagless Vacuum

IS THERE A TOOL TO PUT A BELT ON A HOOVER WINDTUNNEL V6634-900. I CAN'T STRETCH IT ENOUGH.


Thake the roller brush out and that will make it easier to put the belt on the motor axle first and after stretch and put back the roller brush. ... Vacuums

The smaller belt remains slack. the tensioner does not pull it far enough to engage. rotor brush does not spin.


The belt has been stretched, normal wear. buy a new belt, they are inexpensive, best place to getis from shop that repairs hoovers, put it in your self ... Hoover U5780900 Bagless Upright Cyclonic Vacuum

My Bissell 9200 is not sucking the water into the dirty water resevoir. 1. The gasket on the clear-view seems fine. 2. The suction power just doesn't seem powerful enough (feeling with my hand). 3. The brushes turn fine and belt is fine (not sure if that even matters for this issue). Any help appreciated. Thanks, - Matt


Disassemble all lines and check to see if all O rings are installed. If cracked missing or stretched out of shape no suction will be provided ... Bissell 9200 Upright Vacuum

PROBLEM I HAVE CLEANED PART OF MY CARPET, BUT WHAT SUCKS UP THE DIRT OR WATER AS CARPET WAS WET, I HAVE WATCHED A VIDEO, BUT DIDN'T GO FAR ENOUGH TO EXPLAIN THIS, AND WHAT DOES THE BELT DO THAT IS LOOSE FITTING IN BETWEEN EACH SIDE OF BRUSH. KINDEST REGARDS


A Shop vac is my usual solution to my crappy Kirby shampooer.. ... Kirby Heritage II Vacuum

How do I change the belt on a Hoover Steamvac Model # F5905-900. The brushes are not rotating strong enough. They rotate while they are off the carpet but once you lower them to the carpet they stop rotating.


... Hoover F5905-900 Vacuum

Belt type Ok, thank you for the help! I did have the top off, but did not know the taking the motor loose trick, thank you for that! Now I have a couple of more questions, and thank you so much for all of the help! I got a belt from sears, & the sales guy sold me an off brand belt. It looks just like the belt that broke, although do you have to force the motor back down into place? I think it may be the wrong belt? I have looked on the Hoover website & they do not even have parts listed fo


The belt number is 91001028. The belt will be snug but not real tight, so the belt you got may not be the right one. Most repair shops for vacuums should have this belt in stock. ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Belts I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do t


It is the flat belt that gets stretched and should be replaced at least every 6 months. The V belt wears down so it won't it right in the brush roll V. Maybe the belt tensioner wheel has a problem, sometimes they get hook up and won't engage the V ... Vacuums

I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do they re


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=675093\015\012Generic problem for all Vacuums\015\012I have a Hoover self-propelled\015\012Posted by kl ... Vacuums

Dyson Vaccum suction not strong enough


Look for an obstruction in the air passages at the bottom and where the air enters the canister. Make sure the HEPA filter is not plugged (take it out for a test). Hope this helps! ... Vacuums

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v


I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

The roller turns strong and the belt is new,but the dirt accu-mulates and doesnt get sucked up! there no observable clogs and the filter side vent blows strong.......ive removed beater,belt and am assuming there may be a problem inside the motor housing as all else appears normal..i was an aviation mech in the military and the above is my assessment........


Are you sure you have the belt on correctly?\015\012If it is not, the beater brush will push the dirt, etc, in front of itself and not back to the suction port. ... Hoover Tempo Widepath Upright Vacuum - Blue

Help!!!! i have an older model of the dirt devil bagless quick vac. and it has been working great, just last week i was vaccuming my bedroom and i accidentally sucked up a string belt that goes with one of my capris. and today i emtpied out the dirt cup but it seems the the string belt that was sucked up is not within my reach and whenever i start the vaccum i get this distinctive noise that i've never heard before. help.


It's likely wrapped around the brush\015\012pull out the roller and un tangle it ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

I have two old identical 5842's that I use in the garage and around the house. The belt broke on one so I bought a bag of 2 genuine Eurika "U" belts, which is the correct belt for this vacuum. They were obviously smaller than the original belt because they were not stretched out. When I put the new belt on it lasted about 20 minutes and then came off. I put it back on and ran the vacuum with the cover off to see what was wrong. Everything looked fine except the belt rides to the outside edge of


Not 100% sure this is the remedy for that particular problem, but I would take the time to clean both of the brushes that the belts operate, one on each machine.\015\012Remove the brushes and clean as best you can. At the end of each brush there sho ... Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum

I have an old Hoover vacuum model # U5035-930. The belt broke and I tried replacing the belt myself. I couldn't stretch the belt to attach it to the motor pully. It was belt # 38525-027 M6. Which I got from the previous owner. I took it to a vacuum repair place and he replaced it with belt # 38528-027 J4. I cannot find this belt anywhere.


... Vacuums

The belt on my Kirby G3 wore out, and I bought replacement belts from two different sources--one an official Kirby supplier and one a store brand. Neither belt is long enough to catch the belt lifter when it is rotated and to reach the drive shaft.


Kirby has only had 1 belt from day one. sometimes you do need to push the belt up to catch the belt lifter ... Kirby Generation 3 Bagged Upright Vacuum

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?


Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Belt drive Not only do I need a PN for the drive belt on the Panasonic MC-V7395 Vacuum Cleaner, I've noticed that there are problems with the belt breaking. Can someone also explain the proper way to install the belt over and around the motor spindles and any other information that may help. Thank you.


Http://www.partstore.com/Model/Matsushita/Panasonic/MCV7395.aspx?SearchTerm=True ... Panasonic MC-V7395 Vacuum

The belt keeps coming off. There is a little U shaped metal piece that came off when the belt first came off. Where does it go? When we first got the vacuum, we sucked something up and the belt came off and that little metal piece fell out. The belt now periodically comes off when we bump something. Please help us!!!!!!!!!!!!


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0917 seconds