Having problems with your Vacuums ?

Believe the fuse is blown in my fantom fm760 vacuum. put the wrong kind of headlight in and when i turned it on it blew the breaker as well. took apart and the fuse is part of the powercord.


Answers :

Unfortunately Fantom has been out of business since about 2001, so parts are very difficult to obtain. Your best bet would be to try to find the parts online or possibly at a vacuum store, but I would be very doubtful that you will be able to find the parts.
\015\012
\015\012Good luck,
\015\012
\015\012-R
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Believe the fuse is blown in my fantom fm760 vacuum. put the wrong kind of headlight in and when i turned it on it blew the breaker as well. took apart and the fuse is part of the powercord.


Unfortunately Fantom has been out of business since about 2001, so parts are very difficult to obtain. Your best bet would be to try to find the parts online or possibly at a vacuum store, but I would be very doubtful that you will be able to find th ... Vacuums

I was trying to repair my wife's kitchenaid mixer and took part of it apart, including the back part, where the electrical connections are. The original problem was the plastic gear was damaged -- I finally had the good sense to find the solution for that problem on the internet and replaced the damaged part. But now the mixer just won't turn on. I don't think I damaged anything in the electrical section, but I suspect I either blew a fuse or somehow disconnected something.


Do you have a model number? Is the voltage getting to the motor from the switch? ... Vacuums

We just were vacuuming and it stopped as if we blew a fuse. I checked the breaker and it is on and plugged something else in the outlet with no problem but the vacuum won't turn on. Any suggestions?


You said you checked the main breaker but did you change the fuse in the plug ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Henry hoover Hi all, I bought a spares/ repairs Henry on ebay having been told there was no cable rewind and believing that since I had a spare one in the shed it would be an easy fix. However, poor Henry had his cable replaced to find when plugged in, he tries to start but nothing happens. The motor turns once and just cuts out. If you turn it on and off again it happens again. One whir and turn of the motor, then nothing. It blew the fuses out in the kitchen first time too, so could it be a re


Hi it can be the connector at the end of the Henry cable inside the cable rewind unit happened to us! ... Numatic Henry Bagged Canister Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Kenmore 23613 The vacuum when turned on has a burnt smell. My husband has taken the vacuum apart, still can't seem to get to the belt. The belt in the rug part is not the problem, it is something in the canister part. Can you tell me what you think might be our problem? Thanks!


If it smells like burnt plastic it is something wrong with the motor part, but if it is a wet dog,burnt hair gross kinda smell it cool change the bag and buy deoderizer tablet to put under bag kinda like a airfreshener. if it dont work like it used ... Kenmore 22085 Bagged Canister Vacuum

My Hoover Windtunnel blew the circuit breaker today, and did so again after I reset the breaker and turned off the only other appliance on that circuit. Any advice? Thanks from GrGrandma in Fremont


There could be a problem with the vac, the only way to know is to use an ammeter and test the current draw of the unit. If the vac is ok, the breaker could be failing. Plug the vac into another receptacle on a different breaker and see if it still tr ... Vacuums

Apparetnly the fuse blew out. i was wondering where i can get one? the fuse number is 250u. is there a place or a website i can get the part. the microwave won't work or come on. i live in the sacramento area in CA.


Sorry to read about your problem, I hope this helps you out.Radio ShackI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Vacuums

HI, my motorized brush barely turns.It makes a hot rubber smell. I took apart and noticed the spindle the belt turns on discolored from heat. Cleaned it, but still no turning of the brush.The vac is a hoover wind tunnel. As it moved accidentally touched the belt/ spindle and burned my hand a little. Very hot in area. Bright spark from motor noted. Was careful not to touch that part!


That means that the belt is stretched and it is slipping on the motor shaft, that is why it is hot and smells like burning rubber. You need to replace the belt. Here is the correct belt you need: ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I had plugged it in to use it, turned it on and instantly it made a pop sound, smelled of electrical, and would not turn on after. i even waited for a while let the smell go away and tried a different plug in the house and still no operation of any kind. Is there an internal fuse that i could check on this? where is it located?


Sorry there is no fuse in the vacuum. It sounds like there is a short somewhere when they manufactured it. There is no way to fix yourself you will need to take to a repair shop\015\012\015\012Good luck ... Vacuums

I have a Hoover Windtunnel model U5462. Plugged in, turned on, it popped and then no power at all. Not circuit breaker in house. Does the unit have a fuse or something similar?


Does it have a headlight and does it work? if so then unplug the vacuum and turn the brushroller by hand a few times.then plug it back in,if it works then your motor might be bad.you can try to spray a little wd40 into the switch then.work the swi ... Vacuums

Vacuum is not turning on. Is there some kind of a reset switch or a fuse that could have gone out?


There is no reset switch. First try a different electrical outlet. If that doesn't work, you may have to replace the power switch. Call the Dyson Helpline, they'll register your vacuum cleaner and direct you to your nearest repair dealer.\015\0 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My Delonghi D895 Deep Fryer was accidentally turned on without oil in it. It immediately blew the thermal safety device. I would like to repair it myself. Where can I get this part? Thanks


... DeLonghi Vacuums

I took apart the power end that goes into the canister to try and get a kleenex out. in doing so i revealed the brass? rings inside also the prong part was taken out. i thought i had everything back in the way it came out but now it will not turn on. is there a reset but or something? thank you


... Panasonic MC-V9644 Bagged Canister Vacuum

My Air Vac is 20-21 years old. Recently it stopped running. I found the fuse by the motor was blown and replaced it. It blew immedicately when I turned it on. I think I need to repace the motor. Do you agree and can I buy a motor from you.?


If the fuse does keep blowing yes you do need to replace the motor. I am sorry we do not sell parts though. Try the link below to get the motor.\015\012\015\012 ... M&S Systems Vacuums

No power Our dyson DC07 was working fine, then we pushed the button to turn it on. It started to run then shut off and now it is like the power is no longer there. I have checked outlets and they all work. Is there a fuse of some kind in this unit?? If so, how would I get to it?


The motor will have a thermal cut out,however chech your plug fuse and the cable as it enters into the off on switch. its known to snap here within insulation..... ... Dyson DC07 Bagless Upright Cyclonic Vacuum

We have a dc04 and the belt keeps breaking as soon as we turn it on. Have u any ideas as we have took it apart and we think cleaned all parts


If the brush roller is sticky that will put a strain on the belt check it can turn freely and also the brush bearings are free ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My epic 8000 electrolux will not power on. the red light is onat the top handle ( it does not power up) but the bottom part of the floor adapter does not light up at all nor turn on ? is there a fuse ?


If there is light on handle but the electrolux is not starting then the handle switch needs to be checked and its connections.\015\012The vacuum cleaner is operated by the controls on the handle. The handle has different switches which change h ... Electrolux Epic 3500 Vacuum

Fan housing my sweeper was making noises when you turned the brush so i tore it apart and found that the fan and the casing that covers the fan is broken. I can't find parts cause i don't even know what i am looking for. i believe i have a discontinued vacuum as well


Http://www.hoover.com/ will help you find a local repair shop and they can get almost anything Hoover as long as it isn't a crank model. ... Hoover U5254-900 Vacuum

My Bissell Quicksteamer Model 1960-R won't spray cleaning solution. I have cleaned it and taken apart the whole thing. I can't find any problems. The holes are not cloged where the water comes out as I disconnected it and blew through it to be sure. The lines show water trying to go through. It is as if it doesn't have enough power to pump the water out when I squeeze the trigger. I am thinking it is the pump thing but can't find a replacement part for it.


... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

Windtunnel Hello: I was reading thru another readers problem of power to vacuum but won't turn on. Same problem for me. All hoses are free of clogs and I have the vacuum basically taken apart as far as I can. You state a THERMO by the motor may be open. What does this part look like? Thank you. Craig


The thermo is a small square piece with two wires coming out of it. Did you check the switch? The switch has a high failure rate. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover tempo upright is clogged. I can only vac for a few minutes, then I have to unplug it and turn it over and clean out the under part under the roller. It is totally stuffed with dirt and dust and carpet fibers. I have a new bag in. It is like it is clogged up inbetween the bag and the roller. Also gets clogged when using the hose. It is maybe a year old. How can I take it apart and unclog it?


Disconnect the hose and head and wands. Drop a quarter thru the hose, the handle sometimes clogs. peer thru the wands and inspect the elbow on the head for blockage as well ... Vacuums

Kenmore canister model numer 26212690 12.0 amps with powermate. How do you remove the bottom part to check the belt. The blade won't turn and the switich is on rug not wood floor. There are two arrows that say to seperate use screwdriver at arrow. Have seperated at the arrows but the back will not come apart.


Hi There,\015\012\015\012There are actually two screws that need to be removed before you can separate the bottom from the top housing. The screws are actually located either underneath of the headlight cover, or on the bottom of the ma ... Kenmore Vacuums

Hoover U6637-960 the self propel is not not working. When lowering the handle it acts like it would like to work but the roller will not turn. appears to be something to do with the self propel part of the handle . took the screws aout but can not get it apart. Is there another belt of something in there?


This vac has 2 belts. If both self propel and roller not spinning then most likely it is the wide flat belt broken or off. 4 screws on the bottom should gain you access to the belt area. another issue for this model series is a worn pulley on the rol ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Vax 6131 water pump had stopped working on taking apart it had over heated and plastic casing had melted in one place,obtained new pump from buy spares which matched old part fitted and reasembled but pump does not run ,is there any internal fuses ? Or any thing else to replace


... VAX Appliances Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0800 seconds