Having problems with your Vacuums ?

Switching new belt for old on older model 3550 Bissell vacuum. Where does belt go and does it go around sweeper bar?

Answers :

If it has a belt it goes around the sweeper part and connects to the motor.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Switching new belt for old on older model 3550 Bissell vacuum. Where does belt go and does it go around sweeper bar?

If it has a belt it goes around the sweeper part and connects to the motor. ... Vacuums

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc

... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

SHARK CORDLESS SWEEPER 3 SPEED CONTROL FLOOR, CARPET, TURBO BATTERY EURO-PRO 8.4V - 1.3 Ah SB617U 3305 BELT Turned on and almost immediately turned off At least four years old - not used all the time - not used in six months Checked belt - seems O.K. Do I need a new battery, if so, where do I get one? Or should I just get a new sweeper? Cost?

... Vacuums

Replaces the belt on dirt devil dynamite pluse model put everything back together started it and it burt the new belt up that fast. I put it around the beater brush and the metal bar I thought it should go around, yet it seemed like there should be something else there to put the belt on. What do you suggest? Do you have picture I could go by?

The metal bar you put it around if the bar itself does not spin it is going to burn the belt up. Every thing that the belt is supposed to go around has to turn or the belt will rub on the piece not moving and brake. ... Vacuums

I have two old identical 5842's that I use in the garage and around the house. The belt broke on one so I bought a bag of 2 genuine Eurika "U" belts, which is the correct belt for this vacuum. They were obviously smaller than the original belt because they were not stretched out. When I put the new belt on it lasted about 20 minutes and then came off. I put it back on and ran the vacuum with the cover off to see what was wrong. Everything looked fine except the belt rides to the outside edge of

Not 100% sure this is the remedy for that particular problem, but I would take the time to clean both of the brushes that the belts operate, one on each machine.\015\012Remove the brushes and clean as best you can. At the end of each brush there sho ... Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.

You need a new belt. ... Vacuums

Bought a new sweeper and brush ( beater bar ) does not turn. The large belt is fine and turns. The small thin belt is also fine but does not turn the brush. It is either the wrong belt or is there something that could be missing to put tension on it ?? Thank You [email protected]

Jim, To put tension on the brush, tilt machine forward when upright, move carpet selector knob to carpet. then turn vac on. Brush will only spin when vac is tilted back to operate. brush stops when upright and on to use hand tools so the er is no dan ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?

I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

The belt on my bissell 3065 power partner vacuum came off. i looped it around the post located under the roller but it just fell off again. how can i get it to stay on? this vac is 10 years old.

... Bissell 3065 Power Partner Vacuum

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?

Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

Bissell pet hair eraser vac, beater brush stops spinning when on carpet of any length, belt is new, hose is securley attached and it will only spin like a carpet sweeper while on carpet?

... Bissell 3920 Bagless Upright Vacuum

Shark/cordless /sweeper - over four years old. Started - but seemed like it was caught and shut off almost immediately. Not used year around - tried to start after absence. I have removed some hair and perhaps dental floss. Checked belt - it seems O.K. Do I need a new battery or is it just worn out.

Check the brush,is there any dirt got stuck in between brush rolls.If there is then it needs to be cleaned.Your cordless sweeper will automatically shut off if an obstruction is caught in the brush roll. the other thing to checks is dust contai ... Vacuums

The roller will not move around...does that mean I need a new belt for my bissell 6582

Yes that is what that means. It is really simple to do. Here is a link to the belts you need and the manual which has instructions:Bissell Power ... Bissell 6594 PowerForce Bagless Upright Vacuum

I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel

The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t

The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

How do I replace the belt on a Bissel Powerlifter rug shampooer? I have removed the door that is marked "access belts". The problem is that I don't see how to get the belt around the lower roller. There is no problem getting the belt around the upper prong. Please advise.

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

When replacing the beater bar on the Oreck XL upright with a new bar, what way do the words "new" and "old" on the ends of the bar face?

Hello,I don't really understand your question, but I believe you are trying to replace the beater bar of your Oreck XL.... Follow the below instructions on how to replace your vacuum's beater bar:Turn your upright vacuum clean ... Vacuums

Changing a belt on a Hoover Vacuum Cleaner, Model U4264-930. can not get the old belt off.. U4264-930can not remover old belt on sweeper

... Hoover Vacuums

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]

Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o

Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Vacuum started smoking and smelled. Yikes! I new it was the belt. Got a new belt replaced it.... with less than a minute it burned up another. The rotor/ pin that the belt goes around that should be spinning right? What do i do to get it to spin?

... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

My belt broke...I bought a new belt..but I do not know how to put the new on on. I took out the brush roller and put the belt around it but I have no idea how to get it to go on the part that makes it move.

Hello,\015\012Here is a link to my free online guide...\015\012\015\012http://reviews ... Kirby Ultimate G Bagged Upright Vacuum

I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile

... Eureka Smartvac 4870 Bagged Upright Vacuum

Beater bar does not turn. Belt is not broken but is so slack that it won't turn the bar. Do I need a new belt or is there a way to adjust the tension?

No, once the belt is stretched and worn there is nothing you can do, you have to replace them. Here is the belts you need for your model: ... Hoover U6476-900 WindTunnel Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0955 seconds