Having problems with your Vacuums ?

I need the electronic board drawing for Electrolux Induction plate Model :LIBERO DZ/L 2 CE - as one IC need to be changed but it is broken and can not see its value

\015 Model LIBERO DZ/L 2 CE\015

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need the electronic board drawing for Electrolux Induction plate Model :LIBERO DZ/L 2 CE - as one IC need to be changed but it is broken and can not see its value

... Vacuums

I have a Broan Nutone central vacuum. The power head seems to stall unless you lift up on the handle. I think I may need to change the belt but cannot find a place to purchase one to see if this is the problem Model number BN180 type 1

You are correct, you need a new belt. You can find belts for the Broan BN180 at www.vacbelts.com. ... Vacuums

I need to change the motor in a vax 6131 but i don't know how to get into it to get the change it? I also need to get into the motor assembly housing to change a part but can't see how it comes apart!!

On the handle there is one small pozidrive screw, remove and orange panel comes away revealing powercable securing bar. Remove 2 screws and this reveals a 10mm headed bolt. Under label on top of handle there is another small pozzi screw, undo t ... Vacuums

We had to take the machine apart just to see that the belt had broken after only 5 use's . We can not see how we are ever going to put the new belt back on. do you have instructions on how to take the belt off and how to put a new one on? Please send me one.

I have a Panasonic MC-V5746 upright vacuum. According to the booklet, \015\012MAKE SURE UNIT IS UNPLUGGED.\015\0121. Place carpet-bare floor selector in "carpet" position.\015\0122. Remove lower plate (there are two screws in the m ... Vacuums


You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums

I need to change out the short hose on the underside of my older Dyson DC 07 Animal (Light Purple). It is the one less than a foot long on the underside which is attached on one end to the main body of the vacuum(I was able to remove this one) and the top of the upper soleplate. The latter one seems to be glued or otherwise permanently attached.Any assistance you could give me on this would be greatly appreciated....Thanks

Hello Cynthia,\015\012\015\012It's not glued, but it can be a little difficult to remove. You need to twist and pull at the same time and it should pull off. If it's being stubborn, squirt a little bit of WD40 / penetrating fluid where th ... Vacuums

I need please a belt for the brushes the larger one but may be better to replace the smaller one as well. I can see how to replace the small one very easily but not sure how to get the new one onto the end of the big sprocket. Please can you help I have the vac disassembled ok just waiting to get the belt to reassemble it. thank you Colin White SEBO AUTOMATIX X1

As you know, there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pul ... Sebo Automatic X1 Bagged Upright Vacuum

Changing belt how do you change the belt on the power steamer there is nothing on bissells webiste i need to change the one on the sie not the rollers

Take the water and solution tank out of the machine. turn it over an on the left hand side you will see a red clip with a screw in it. take out that screw. flip the unit back over and take off the belt access cover by sticking a straight screw dri ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Dyson DC07 The plastic pre filter catch snapped on my Dyson. I have a replacement already, but can't figure out how to remove the bottom of the broken one. It looks easy enough to slide/snap the new one in but accessing the old one isn't easy. What do I need to do to get it out?

Turn your dyson over so you can get to the bottom undo the screw and then you can see the bottom of the clip a gentle tap with with a screw driver blade will knock it out and the other one slips in ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I was changing a light bulb with one of those metal extension rods that unscrew and screw back in the replacement bulbs. It evidently didn't seat correctly and pulled off the bulb and created a quick "poof" type electrical short. I have switched out that bad bulb with a new one and can't get either the fan or lights to work. There doesn't appear to be a reset switch. I also swirched out the wall switch to see if that would make a difference and it does not. Any thoughts or ideas would be appreci

If you have not already done so, I would check at the fuse or circuit breaker panel to see if you have blown a fuse or tripped a breaker. ... Vacuums

Changing fan I changed the broken fan in my eureka 1934A. Put the cover back on and reattached the belt and when I went to start it, it wouldn't work. I took the cover back off to see what was going on and it looked like the motor was running in reverse of what it had been. Is this possible?

My solution is one that only works if the vacuum is a spare... To get mad at it and throw it in the garbage... \015\012\015\012My thought though on what the problem actually was... Seeing as where the vacuum came from and what the problem ... Eureka 1934 Bagged Upright Vacuum

I was vacuuming and noticed that the bag needed changing. the red light with the ! inside the triangle also came on. When the bag was changed, the vacuum would not restart. The red light came on. Tried the reset button but nothing happened. Tried unplugging and re-plugging in and nothing happened. Replaced all the filters and still it wouldh't start. So I brought it downstairs and tried one more time to get it to start. it worked! Is there something wrong with the vacuum cleaner? Was it overheat

It was overheated that is why it worked downstairs after cooling off. ... Miele S548 Bagged Canister Vacuum

I have a Howard Miller Westminster Chime Mantle Clock. It has always worked fine. It stopped working and my husband took the battery out to change it and when the new battery is in it will not work. It is Model 613-=103 movt 354201J dial 272142J. The part you put the battery in almost looks too big for one double A but I can't see how two would fit. I am afraid the battery is just not in right. Can you help me with how many batteries go in this clock or if it is one what the problem could be.

... Vacuums

I cannot charge my two year old electrolux pronto. I purchased a brand new hand held vacuum for it, but even the new one does not charge. When I plug in the cord nothing happens. If I turn on either the long handle or the portable unit within the long unit, the blue charging light comes on for a few seconds, then out. This tells me that the circuit is intact without a broken wire somewhere. I took it all apart carefully and could see nothing broken or out of place. On re-constructing it, it

It must be the charging transformer. We have already ruled out the vacuum unit. Unfortunately the transformer is not a serviceable part, and will need to be replaced. ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne

Hi i was given a dunhill lighter as a presant the flint needs changing but i cant see how you change it could you advise thanks

... Vacuums

I think i need to change the belt on my vacuum, there seems to be a loss of suction when pushing the vacuum. Where can I get one and how do I change it?

How do I fix a broken belt on my vacum ... Eureka 4700A Maxima Bagless Upright Vacuum

Is this free? i have a bissell carpet cleaner and i cannot get the soap and water to come out. it will **** up the dirty water however. i just found the belt is broken but i can see no way of how to put a new one in. is a broken belt the reason no soap is coming out?

If it is the flat belt that broke, that is the pump belt, the pump can't work without it. To replace the belts, turn the unit over, remove the red holder, has one screw, pull it out, then the brush roll will come loose. You can replace the belts th ... Bissell Powersteamer 1694 Upright Vacuum

I bought new belts to replace the old ones (one had broken and the water would not feed) My cousin took it apart and now I need to put the new belts on and get it back together - do you have instructions or a diagram?

There are different variations with Bissell. They have the ProHeat series and a Power Turbo series. Below is a link with instructions and diagrams for the Belt Access Door. If this doesn't solve your problem or isn't the correct model, please post ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help

Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

I broke the handle part of the shark steamer #53101. I don't have the book to try to tell you the parts I need. Can you send me a picture or a copy of the steamer. It is purple. The above number may not be the correct one. It is broken in the center part. It has a little small circular piece that joins the two pieces which are broken. The beginning of the handle at the bottom of the steamer and the next session which has the steam release. The top of the handle is okay . It the middle and bottom

Hi,Ann there are very few parts for these...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Panasonic mc-e4113 Upright vacuum. The belt that drives the brush in front is broken I have found a spare for this but there seems to be a pulley missing on the main drive shaft that the belt needs to fit on. I can't believe that there wouldn't be one? Can anyone tell me if this is the case and if so where I can get one from. Many thanks Sean

... Panasonic Vacuums

Power head on my Electrolux Epic stopped working. Do I need a new one or could there be a part that needs replacing. Can I open it to see?

Have you tried pushing the reset button? I'd try that first. If that doesn't work it could be that the belt is broken. The motors don't go out very often on those. ... Electrolux Epic 6500 Vacuum

Foot latch is broken. need to replace with new one. how does one access to remove the foot pedal latch. By foot latch, I mean the foot lever that releases the upright to lower the handle and begin vacuuming.

It is accessed from the bottom underneath by the rear wheel. However, If there are and cracks on the pedal release socket area then the base will need replacement. parts are little cost but the unit needs to be completely disassembled. ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

Change belt How do I change the belt Eureka whirlwind 4480. As I look under the house I think I see one screw on each side down in about 3/4 inch. Are those the screws to remove and are there only two you have to remove?

... Eureka WhirlWind 4381 Upright Vacuum

Need to see a picture of a eureka ez kleen upright bagless just recieved one free and I don't know what kind of filter as here isn't one in it would appreciate any help

Here is a set ..\015\012\015\012 ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0994 seconds