Having problems with your Vacuums ?

Replacing belt on a kenmore canister rug beater attachement

Answers :

Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replacing belt on a kenmore canister rug beater attachement

... Vacuums

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each

Should be a pry off dot on the underside revealing a screw ... Vacuums

My beater bar on my Kenmore 116.25615506 canister vacuum keeps turning on and off when I vacuum rugs. The suction continues, but the beater bar seems to be shorting or whatever. I checked the belts and they look like new. Any suggestions? The rest of the vacuum works fine!

... Kenmore 25512/ 25513 Progressive Canister Vacuum

Replace belt on cartpet attachment (kenmore)

On the newer models remove 2 screws on the bottom of the powerhead,also you need to pry the cover of in the back and sides.\015\012they slip over a little ledge and hook to hold in place ... Kenmore 22812 Bagged Canister Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu

This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

Kenmore canister vacuum how to replace belt - Kenmore 22313 Bagged Canister Vacuum

... Kenmore 22313 Bagged Canister Vacuum

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.

Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums

Kenmore 23613 The vacuum when turned on has a burnt smell. My husband has taken the vacuum apart, still can't seem to get to the belt. The belt in the rug part is not the problem, it is something in the canister part. Can you tell me what you think might be our problem? Thanks!

If it smells like burnt plastic it is something wrong with the motor part, but if it is a wet dog,burnt hair gross kinda smell it cool change the bag and buy deoderizer tablet to put under bag kinda like a airfreshener. if it dont work like it used ... Kenmore 22085 Bagged Canister Vacuum

I have a Kenmore canister model 116.25812 that makes a very loud beating noise when the powermate is turned on. I replaced the belt, but still has the sound. Also replaced the bag and both filters. Suction is great, but is very loud when the brushes turn.

... Vacuums

Need tp replace belt on Kenmore CB-3 - Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Rainbow Series E is leaking. Not sure if water is leaking from the water bin (doesn't appear to be cracked/broken). If not the bin, where else might water be leaking from and what are repair options? Have replaced belt on carpet attachment, cleaned the opening where hoses attach to the canister, etc

You need to clean the separator. ... Rainbow E series Canister Wet/Dry Vacuum

Power cord can not find replacement power cord for power brush attachment on kenmore canister vacuum, model #2491290 power brush attachment model # 5491290. i can not even find those model #'s anywhere online, not even partsdirect.com. any help would be great. thanks, david

Call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est ... Vacuums

Belt repair how do i replace the belt on kenmore canister progressive

If im right on the top where you change the settings for your carpet there should be 2 screws take th e whole top cover off theres a plastic cover for the belt take that off and the rest should be self explanitory ... Kenmore 25812 / 25813 Progressive Bagged Canister Vacuum

Sears progression kenmore canister va. Model 11623612300 on the wand, the plastic piece broke off, there is one long wand with two piece to it well the plastic piece, not on the bottom, where it hooks into the beater bar thing, but the other plastic in the middle. Can this be replaces?

Hi.The part is probably available as replacement.Please click here ... Kenmore Vacuums

I have a kenmore vacuum cleaner model # 116.23612. When the hose is attached to the canister it runs, but if you remove the head to just use the hose the unit stops working. Is the motor dead or is there some type of reset or fuse. Could you please tell me how to test this. If so could you please send me instructions on how to replace the motor. Thank you in advance for your help, Tony

... Kenmore Vacuums

We have a kenmore canister vacuum, the part that is attached to the wand that picks up the dirt doesn't work, when it's on the carpet the light does not go on. Do we need to buy a new vacuum or is there a replacement for this part.

Hard to say without the correct model number.\015\012\015\012However, you could check these things first:\015\012\015\0121- Is the belt that runs the brushes on the end pieces broken? If it is, is needs to be replaced.\015\0122- Is there ... Kenmore Vacuums

How do I replace the belt? - Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

How do I replace belt on hoover s1147 twist & vac? I know it goes on the middle of the beater bar but I cant see where to attach the other end to.

... Hoover S1147 Twist Vac Handheld Vacuum

Wiring the switch for a kenmore vacuum cleaner I need to know where teh different colored wires go. It had a short in it so I replaced the plug but think I wired it incorrectly. Its a Whispertone 300 model 116.28612790 The canister works but the beater bar doesn't.( it worked before a rewired the switch. Thanks

... Kenmore 23313 Whispertone Bagged Canister Vacuum

Kenmore canister model numer 26212690 12.0 amps with powermate. How do you remove the bottom part to check the belt. The blade won't turn and the switich is on rug not wood floor. There are two arrows that say to seperate use screwdriver at arrow. Have seperated at the arrows but the back will not come apart.

Hi There,\015\012\015\012There are actually two screws that need to be removed before you can separate the bottom from the top housing. The screws are actually located either underneath of the headlight cover, or on the bottom of the ma ... Kenmore Vacuums

How do I replace belt on kenmore canister vacuum

On most models the head light cover comes off and there is two screws.first look for a little red button its a reset ... Kenmore Vacuums

We have a Kenmore canister vacuum cleaner. the carpet cleaning attachment, I think is called the power mate has a beater that is intermittently working now

Contrary to your advice, the nozzel cannot be connected directly to the powerhead--the female openings are set closer together in the nozzel than the male plugs in the powerhead. ... Kenmore 23812 Progressive PowerMate Bagged Canister Vacuum

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced

There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

Kenmore Quick Clean Advanced Allegen - The plastic screws (for the cover that houses the belt and beater bar) are broken. Is there a replacement cover?

Go to Sears.com, click on parts, put in your model number, a parts list is available, also a picture diagram of it. You can purchase what you need from this site. ... Vacuums

I need to replace the vaacum belt and don't have a manual. Kenmore Canister

I need a manual for kenmore vacuum clearner #116 23812300 ... Kenmore 25512/ 25513 Progressive Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0929 seconds