Having problems with your Vacuums ?

My Bissell Powerwash Deluxe will not dispence the water, i have cleaned all the pipes and checked the belts, all fine, any other ideas!!!

Answers :

This video is a good place to start , if thid does'nt work you need to check the heater tank for blockages
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bissell Powerwash Deluxe will not dispence the water, i have cleaned all the pipes and checked the belts, all fine, any other ideas!!!

This video is a good place to start , if thid does'nt work you need to check the heater tank for blockages ... Vacuums

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John

It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum

My Bissell ProHeat Pro-Clean upright cleaner won't spray either water or solution onto the floor, however it does spray when using the attachments on the hose. The belt is fine, I've actually tried all of the troubleshooting steps indicated in the User Manual. I'm not even certain where it is supposed to be spraying out from! Any ideas where/what to check for?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o

Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell Pro-Heat 7901-1 no cleaning solution is pumped out. The flow indicator is spinning and the belt is spinning the beater bar. Have cleaned the flow indicator, checked vavles in the solution tank and water tank and they are working properly. Also checked the trigger to make sure it works okay. Any ideas?? Moody Fan

Bissell Pro Heat shampooer - Fill the soap dispenser with extremely hot water and shampoo with only water for a few minutes. There is often dried soap in the lines. Make sure that all filters are clean. Press the soap container and the water conta ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and

The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The brush rollers on my hoover mach 5 won't turn. I've cleaned everything and checked the belts and everything checks out fine. I had the vacuum for about a year.

I had the same problem. The problem is the small v-belt for the roller brush (Hoover part# 38528034). Although it looks in good shape, it's been stretched too large for the idler to keep good tension. The tension on that belt varies with the ... Hoover Vacuums

Bad smell after using my windtunnel for a couple of minutes i noticed an odd smell. i turned it over and checked, the belts are fine but i cleaned out the hair anyway. after doing that the self propel seems to struggle and it is hard to push. when i look through the window on the top i can see the brush spinning freely but then when i push it, it slows down dramatically and then picks up again. the suction is fine. what do you recommend?

It may be the roller bearings? ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.

... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

Just bought this Hoover Fusion vaccum used, cleaned it up, checked belt and filter, turned it on and is extremely loud, almost like a scream. Any idea what could be causing this and how to fix?

Loud noises from this model are caused by dirt build up on the suction fan mounted directly to the motor. Under the dirt cup there is a filter screen that should have a foam filter insert, when not used or cleaned properly allows dirt to get into the ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

My bissell won't spray. I've checked the hose and belt, those look fine. Any other ideas?

It could be blocked within the machine, there is a pump located in side - they get bunged up or clean the spray bar where it comes out at the front ... Vacuums

Oreck XL21 just will not work at all any more. Beater is clean - belt is fine. Fresh bag - inflates. Took the thing apart - checked for blockages at intake, bag entry, and the tube. It just doesn't vacuum anything. No suction at all for anything stronger than air. I'd say it doesn't ****, but that would be ironic. Are these known for just "quitting" after a while? We take it in for maintenance as recommended to replace filters, etc. Is there some miracle trick to make it work or sho

Did you make sure the brush turns freely? Even though it is clean, if it does not turn freely with the belt, it will not beat the carpet and pull debris up into the unit.\015\012\015\012Another (drastic?) thing to try would be to take the unit ... Vacuums

I have a Bissell PROheat 2X shampoo carpet cleaner and the brushes stop working. i have changed the motor and checked the belts. everything is fine. any ideas?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?

Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

With cleaning carpets with the Stowaway when the head gets a blockage it makes a high pitched whining sound and requires unblocking - then works fine. Now when vacuuming the head always makes the same sound when the head is against the carpet. you can also see that the rollers are slow or stopped. We have pulled the Stowaway virtually completely apart and checked for blockages as well as washed the filter and no difference. Any ideas?

... Dyson "Stowaway" Canister Vacuum Vacuum

I have a Eureka Altima vaccuum and it no longer suctions like it use to and also has a burning smell. I have cleaned all filters, brush, hoses, and filters. There are no blockages. I have also checked the belt and it's still good. Any other ideas as to what may be the problem?

This bagless model gets buildup of really fine dirt in the motor and starts to clog up the fan airducts. You will need to take the motor out and clean it. ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I plugged it in, pushed the power button and it came on for about 5 seconds. Then, it shut off by itself. I checked the outlet and it was working fine. I then cleaned the brushes and tried again, but no power... Nothing. Could it be the cord??? Any other ideas? Thanks for your help!

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Bissell pet hair eraser model #3920. It's been working great until last night. I went to use it and the brush won't spin. It also smells like it's burning. I checked the belt and it looks fine, and the brush spins by hand easily. It's not clogged anywhere that I can see. Anyone have any other ideas? This vacuum is only 8 months old.

- Remove the access panel, which is on the bottom of the machine. There are 4 tabs to lift on the access panel to remove. Start with tab 1 then 2-4 tabs.- Check the brush, and belt for any damage. Clean off any debris on the brush. ... Bissell 3920 Bagless Upright Vacuum

Loud noise I ran over a string and then shut it off quickly. It now makes a horrible grinding sound. Did I ruin the motor? Sounds like something came undone. I checked the belt and that is fine. Ideas?

I think you damaged the belt. I ran over a sock once and it made a grinding noise but still worked for several months after the incident. Finally, the belt broke off. I had it replaced and now it doesn't make that sound. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Bissell 7920 ProHeat and only used it 4 times and the brush on the bottom has stopped spinning and when attempting to spray solution the flow indicator doesn't spin and nothing comes out. I have looked at all of the belts and they seem fine. I have also removed and cleaned the heating unit. Still nothing. Any other ideas?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Beater bar won't work. Have done all checks in manual. Bar is clean, belt seems to be connected properly and in good shape. Any ideas? John Rike [email protected]

Hi, I would have to say, that if the roller-brush Is clean and the belt is on and in good shape, that the problem will be in the vacs motor assembly itself. If the motor comes on, the beater bar will engage and pick up debris.If it is coming on and n ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Dirt Devil Vision and when I put a clean canister back in place the suction at the bottom of the filter clogs up and very rarely go into the canister. Also where the air blows out of the motor, I will get particals that will blow out. I have checked where the belt is and also the suction tube. Do you have any ideas how to fix this problem?

Yes your intake hose is clogged thats the clear hose you can see it on the bottom from the back.disconnect the upper hose from your intake hose and try to push a coat hanger through with the end of the coat hangers end bent till its rounded so you do ... Dirt Devil M086700 Vision Bagless Upright Vacuum

My vax won't **** dirt up but suction feels strong when I put my hand on the end of the pipe. I've checked it's empty,cleaned the parts including the filter and there aren't any blockages. What else could it be? What can I do to fix it? It's a model 121 (orange) and about 17 years old (worked fine until this week) Thanks in advance!

... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Hi, I have a Hoover windtunnel t series vacuum. It was working fine until the last couple of times I used it. It just does **** uo the dirt. It **** a little, but not as strong as it used to be. Already checked for clogs (didn't find) and cleaned it and still doesn't work. Any ideas? Thanks!

This model, along with some similar ones, has been recalled. Stop using immediately. See the following site for information.\015\012\015\012 ... Hoover UH70205 WindTunnel TSeries Rewind Plus Bagless Upright Vacuum

Have ultra vision and have changed filter and foam filter, checked all hoses but still will not pick up. Belt is fine and brush is clean and spinning properly. dirt stays at top of filter instead of falling into canister.

My kids get mine stuck all the time :(Take the vacuum outside then:Remove the hose at the bottom and see if there is any obstructions. Also shake the hose to make sure there is nothing in there as well or take it out side and make s ... Dirt Devil Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0729 seconds